Hi, Naktal! You're very welcome. We'll continue this video series for sure. You can watch the previous parts for more basic information on PLC programming: Part 1: ruclips.net/video/P1qCp4wlyLg/видео.html Part 2: ruclips.net/video/CM6DntkoYyQ/видео.html Part 3: ruclips.net/video/51hELJPg4kU/видео.html Please don't hesitate to ask your questions.
Hey! Great to see you here again and happy it was helpful to you. We have some plans to subtitle the videos in other languages. We will consider the Russian as one of the priorities. Thank you for your comment and happy learning!
That was awesome! Great drawings and didactic! The video is straight and objective. Is always easier to learn when our teatcher knows how to teach and is real teacher!
You should add nc contact of contactor in picture with motor, just near the no contact. For better understanding how the lamps are charged. Thanks a lot for video
Very good content. I hope your channel will grow up fast. In 0:35 we can see the hardware config, is it possible to save the hardware config in PDF format or JPG ? I have TIA Portal but no way to save it, i had to take a screenshot and this will not take the full config.
Thank you very much! Please support us by sharing the videos with your friends. Unfortunately, I did not find such a facility in TIA Portal V15.1. There are some options to import the HW config to other projects. But PDFs or pictures, I don't think so!
From this link, you can find the recommended hardware for installing the TIA Portal V15 (in the middle of the page): sie.ag/37VWEXG I doubt you can install it on your computer. Although if you can, then most probably it won't run smoothly. I think your RAM is the most critical part of your hardware for installing (or using) TIA Portal V15 which according to our experience should be at least 8GB.
Why are you connect normal closed switch to the Reset of the flip-flop? So it will remains 1 until you press it, and it became 0. When the Reset = 1, the Q is 0?? I just don't understand...
Hello sir .. i need help . Im a student Making a PLC ladder diagram.. please help me .. its verry easy but i cannot answer. Im only first timer.. heres my problem. When you press Push Button (PB1) - X21 the output bulb (YO) will lit… When you release the PB1 the output bulb will off. Im done subscribing your channel.. Please help me
Hey! We have missed your comment! Sorry about that! If you use an SR FF same as what has been explained in the video then you should achieve the same result. I'm wondering if you want to do the same thing with a single PB?! (the program would be different a little bit in this case)
This video was very helpful thank you for your channel
Glad it was helpful, Mahdi! You're so welcome!
Thank you very much ... I hope for more videos on plc ... I need a tutorial video from the beginning.
Hi, Naktal! You're very welcome. We'll continue this video series for sure. You can watch the previous parts for more basic information on PLC programming:
Part 1: ruclips.net/video/P1qCp4wlyLg/видео.html
Part 2: ruclips.net/video/CM6DntkoYyQ/видео.html
Part 3: ruclips.net/video/51hELJPg4kU/видео.html
Please don't hesitate to ask your questions.
Thank you for the video!I watch with subtitles translated:)I have problems with English:)
Hey! Great to see you here again and happy it was helpful to you. We have some plans to subtitle the videos in other languages. We will consider the Russian as one of the priorities. Thank you for your comment and happy learning!
Sir your teaching is amazing Do make more video
Thank you for your comment! We try to do so.
Great information. Subscribed!
Thanks for your support!
Good teaching
Thanks a lot!
Hey bro, I love your videos. It helps me a lot. Keep it up, please!! Thank you.
You're very welcome! Please stay tuned for the upcoming videos.
Great video!!!
That was awesome! Great drawings and didactic! The video is straight and objective.
Is always easier to learn when our teatcher knows how to teach and is real teacher!
Would be great if y'all had a video for changing between VFD/third party equipment, GSD file loading etc
Sounds like a good idea! Thanks for your suggestion. I'll transfer it to the team.
Hi... I am going to say a BIG WOW... the best video that I've seen here... Would you do videos with Allen Bradley?
Thank you! It's amazing to hear that we could help. Yes, of course we will. Please stay tuned for more.
we need more videos!!
Hey! We'll publish a new video next week.
This video is very helpful. Pls can you make another video of how to wire of two PLC with interlocking . thanks and highly appreciated.
Sure! We will put it in the plan. Thanks for your suggestion.
exceptional
You should add nc contact of contactor in picture with motor, just near the no contact. For better understanding how the lamps are charged. Thanks a lot for video
Thanks for your support!
thank you dis lak
can you please do the plc ladder diagrams in bosch rexroth software ?
thank you man like
please make video on Communication protocol and how they connect to plc and other instruments..please
Hey! I'll transfer your suggestion to the team. Thank you!
my friend your all videos is very good. my friend can you explain marine main switch board circuit diagram with synchronization circuit diagram
hello. it is a good video for learning. it would be very easy if used İ0.1 NO instead of İ0.1 NC. because stop button is normally close.
Thanks 👍
Welcome, Alexandr! Let us know if you have any questions or suggestions.
tahnks ❤️
You're welcome! Thank you for watching!
Good job
Thanks a lot!
Hi sir thank you for good explanation
Can you help me to get this simulation software please?
Hi there! We have used the Siemens PLCSIM Software. If you mean the graphics in this video, these are not a part of the Simulation software.
Very good content. I hope your channel will grow up fast.
In 0:35 we can see the hardware config, is it possible to save the hardware config in PDF format or JPG ? I have TIA Portal but no way to save it, i had to take a screenshot and this will not take the full config.
Thank you very much! Please support us by sharing the videos with your friends.
Unfortunately, I did not find such a facility in TIA Portal V15.1. There are some options to import the HW config to other projects. But PDFs or pictures, I don't think so!
It's awesome video.. anyway sir what is the meaning of Q.0.1 ty for you answer 👌
Thank you!
"Q" is a sign for the Output coils in PLC programming; especially in Siemens PLC programming environment.
good job
Thank you!
Great !
Thank you!
nice channel. where can i get that software?
Hey! You can download the TIA Portal V15.1 from here: sie.ag/3h17ShN
What is the logiciel name that allow you to create this modele . ❤thank you
I need a full tutorial to make a test project
I have i3, with 4GB RAM on operating system of 64-BIT windows 10.i just want to ask, is it compatible to run V15. 1 TIA?
From this link, you can find the recommended hardware for installing the TIA Portal V15 (in the middle of the page): sie.ag/37VWEXG
I doubt you can install it on your computer. Although if you can, then most probably it won't run smoothly.
I think your RAM is the most critical part of your hardware for installing (or using) TIA Portal V15 which according to our experience should be at least 8GB.
@@Upmation thanks.
Why are you connect normal closed switch to the Reset of the flip-flop? So it will remains 1 until you press it, and it became 0. When the Reset = 1, the Q is 0?? I just don't understand...
👍따봉
Hello sir .. i need help . Im a student Making a PLC ladder diagram.. please help me .. its verry easy but i cannot answer. Im only first timer.. heres my problem.
When you press Push Button (PB1) - X21 the output bulb (YO) will lit… When you release the PB1 the output bulb will off.
Im done subscribing your channel..
Please help me
Hey! We have missed your comment! Sorry about that!
If you use an SR FF same as what has been explained in the video then you should achieve the same result.
I'm wondering if you want to do the same thing with a single PB?! (the program would be different a little bit in this case)
Can I install this software if I already install Nx 12 in pc
Yes, I think so.
Make more videos
❤️❤️❤️❤️
where we get software free?
TIA Portal has not a free version unfortunately.
why would anyone need a plc for such a simple task