Excellent informative videos. You’re my ‘go to choice’ for ALL my 2011 fiesta s needs. Concise explanations & great lighting & angles. Makes all the difference for us DIY’rs. Thank you!
Thank you for this video. I’ve been trying to get my check engine light checked out but every time I’d get there it would shut off. I finally was able to catch it last night and got the P0054 code.
Excellent. Thank you. Could not find where the connector was just looking at it from above. Under the heat shield. Needed to make sure the replacement had the right connector.
Great video! Only thing I would add is rather than fart around with the claw end, thread the cable through the box end and get it from the engine compartment
Great video. I’m having a P0420 code on my son’s 2015 Fiesta. It only has 61,000 miles on it. Can’t believe the cat converter is bad already hoping it’s just the o2 sensors.
The symptom for this problem is that the engine light comes on, on the dash, next to speedometer. You can detect the code for the problem with an obd2 scanner. I can also use the OBD2 scanner to turn off the engine code light and see whether it comes back on.
I've been trying to diagnose or fix P0053 (H02S11) heater resistance out of limits on my 2011 Ford Fiesta without any luck. I replaced the upstream sensor with a new one from Amazon but I still receive the same error. I checked all fuses and wiring in the car and they all seem fine. I verified that the voltage produced by the sensor falls in the .1 to .9 voltage range. I also checked the heater resistance of both sensors old and new using a multi-meter. The resistance on both is 4.5 ohms. Does anyone know what the resistance value should be? I don't have that information. Is there anything else I can look for? I am at a loss and super frustrated at this point.
I deleted the code with my scan tool before I started it. But it should clear a little bit after starting it. Once the o2 sensors starts seeing the correct readings.
My 2013 ford fiesta se keeps getting a wrench light and says engine malfunction service now but it doesn't give a code because when turn off the car it clears but the light has came on more frequently now while I'm driving and car just stops driving anyone have an idea of what it is?
Excellent informative videos. You’re my ‘go to choice’ for ALL my 2011 fiesta s needs. Concise explanations & great lighting & angles. Makes all the difference for us DIY’rs. Thank you!
Thank you for this video. I’ve been trying to get my check engine light checked out but every time I’d get there it would shut off. I finally was able to catch it last night and got the P0054 code.
Excellent. Thank you. Could not find where the connector was just looking at it from above. Under the heat shield. Needed to make sure the replacement had the right connector.
Great video! Only thing I would add is rather than fart around with the claw end, thread the cable through the box end and get it from the engine compartment
Thanks this is exactly what I needed to see
Great video. I’m having a P0420 code on my son’s 2015 Fiesta. It only has 61,000 miles on it. Can’t believe the cat converter is bad already hoping it’s just the o2 sensors.
Thank you very much for the video, already did the replacement and my car got much better, it have other codes but I'm going to look on them.
The symptom for this problem is that the engine light comes on, on the dash, next to speedometer. You can detect the code for the problem with an obd2 scanner. I can also use the OBD2 scanner to turn off the engine code light and see whether it comes back on.
massively useful, thank you for sharing this
Great video! Thanks for sharing 👍🏽
Just did this today to my car.
I've been trying to diagnose or fix P0053 (H02S11) heater resistance out of limits on my 2011 Ford Fiesta without any luck. I replaced the upstream sensor with a new one from Amazon but I still receive the same error. I checked all fuses and wiring in the car and they all seem fine. I verified that the voltage produced by the sensor falls in the .1 to .9 voltage range. I also checked the heater resistance of both sensors old and new using a multi-meter. The resistance on both is 4.5 ohms. Does anyone know what the resistance value should be? I don't have that information. Is there anything else I can look for? I am at a loss and super frustrated at this point.
Thank you for great video, need a favor from jedi master to point where is the MAP sensor?
you the man💪🏽
How long did it take for the permanent code to clear after the repair? You can only clear the pending and confirmed codes with a scan tool.
I deleted the code with my scan tool before I started it. But it should clear a little bit after starting it. Once the o2 sensors starts seeing the correct readings.
My 2013 ford fiesta se keeps getting a wrench light and says engine malfunction service now but it doesn't give a code because when turn off the car it clears but the light has came on more frequently now while I'm driving and car just stops driving anyone have an idea of what it is?
Have you had it scanned for codes to see what it’s throwing?
THANK YOU
Perfect
Thank u!
Gracias!!