Pete I love watching you restore this old tractors. My uncle owns and old allis Chambers c that I would like to get working one day it has sat for a really long time.
Hey Pete, I enjoy your videos, especially the ones about rebuilding the Farmall MD engine. You are an excellent communicator and explain things well. When I cut off a bolt, a nut will never screw on the bolt. What I do is to take the bolt I have cut off to a bench grinder. Hold the bolt at a 45 to 60-degrees angle to horizontal and grind all around the end of the bolt. A nut will always start. Give it a try
I have to admit I have found myself looking at my RUclips a few times the last couple of days for the updated videos , what can I say I really enjoy this series of videos along the rest of the channels content mostly cause you can learn and have a take away from each video. Keep up the good work!
I’m a retired accountant without any mechanical knowledge. I am in awe of your skill & knowledge you have with these motors. Love watching.& getting the explanations. Thank you.
Thank Pete for the lesson on the timing. I'm restoring a co op E3 IV been trying to find the right way for the lash. I was told if you found TDC compression you could adjust 1,2,3,5 and do one complete Revolution then do 4,6,7,8. I tried it and it didn’t work I’m going to try it the way you explained it. Thanks again!!
You have reached a milestone in the restoration on your MD tractor. We are happy you now have most of the engine painted so it won't be too long before we can hear the engine purrrr. Pete, you sure are a great teacher on engine restoration.
Pete you remind me of one of my auto mechanic instructors when you have those gloves on. He told us to treat all engine parts like we were doing surgery. Nice job and I enjoy your explanations when dealing with each component.
I love what you are doing with this engine. I especially liked that you chose to use the original o-rings for the injectors. It reminds me to keep everything during disassembly. You never know if you need them or use them for reference because it's a genuine part.
Hey Pete I also live in New York and am a hour away. And I know that you live in New York because I have gone past your farm a couple of times and remembered it in the videos.
That's a good move, Pete, putting a die on the bolt before cutting it. For those that might not have a die, a standard nut will suffice. Also to keep the stud from turning, a double nut one those threads tightened up and held in the vice will be a good step as well. This is the same technique that you used later in the vid.
Doing a heck of a job! I use the same method for installing valve cover gaskets, seems to work like a charm! Is the valve lash setting specified cold or hot in the manual? I know on a gas M the valve lash is .017" hot. I usually set them to about .019" cold for initial start up.
Well, it may be frustrating to you, but I am enjoying the journey. Setbacks, they happen, but all I can say is that that engine looks really nice! Please keep going, I am eager to see it fire up for the first time after the total rebuild!
Looks awesome Pete been following this built and enjoy your channel a ton!!! you mite pick up a crows foot wrench to adapt your torque wrench if this is a problem you have frequently for those pesky tougher spots when torqued bolts are a issue. Great job pete!!!!
Easy way to clean treads after a bolt was cut off. file or grind from the bolt head side. it will remove most of the burs. The slight taper will also assist with setting the bolt.
Pete I love watching you restore this old tractors. My uncle owns and old allis Chambers c that I would like to get working one day it has sat for a really long time.
Awesome to see Jay Lenno working on his own equipment!! Your doing an awesome job fellow New York farmer!!
Great video series. Try a few drips of oil on the o ring when installing. It keeps the ring from binding and tearing and makes it go easier.
Looking Awesome Pete, can't wait to see it All put back together 7 to Hear that 1st Start up!!
Hey Pete,
I enjoy your videos, especially the ones about rebuilding the Farmall MD engine. You are an excellent communicator and explain things well.
When I cut off a bolt, a nut will never screw on the bolt. What I do is to take the bolt I have cut off to a bench grinder. Hold the bolt at a 45 to 60-degrees angle to horizontal and grind all around the end of the bolt. A nut will always start. Give it a try
I have to admit I have found myself looking at my RUclips a few times the last couple of days for the updated videos , what can I say I really enjoy this series of videos along the rest of the channels content mostly cause you can learn and have a take away from each video. Keep up the good work!
Looks great Pete!!!! I enjoyed watching your videos.
Nice job Pete, it's looking great! I am sure it will run as good as it looks.
I’m a retired accountant without any mechanical knowledge. I am in awe of your skill & knowledge you have with these motors. Love watching.& getting the explanations. Thank you.
I'm currently in the middle of restoring an old tractor so I love watching this series
You are doing an excellent job and giving excellent details. They need to use these videos for class instructions.👍👍👍
My husband is enjoying all your videos. He's impressed with what you do accomplish with working on these tractors. Be well.
Thank Pete for the lesson on the timing. I'm restoring a co op E3 IV been trying to find the right way for the lash. I was told if you found TDC compression you could adjust 1,2,3,5 and do one complete Revolution then do 4,6,7,8. I tried it and it didn’t work I’m going to try it the way you explained it. Thanks again!!
I love your videos. My family were small farmers and worked like you until the laws just got to strict .I love the tractors !!
Excellent series Pete. You deserve a lot of credit for taking time to shoot and edit these videos. Thanks.
You have reached a milestone in the restoration on your MD tractor. We are happy you now have most of the engine painted so it won't be too long before we can hear the engine purrrr. Pete, you sure are a great teacher on engine restoration.
I love watching your videos. It helps me relax when I watch you work on tractors and mess with the animals.
A pleasure to watch you Pete from Paul in NH
I can almost smell the fresh paint getting hot during her first fire up. Love those smells on fresh motors!
Pete you remind me of one of my auto mechanic instructors when you have those gloves on. He told us to treat all engine parts like we were doing surgery.
Nice job and I enjoy your explanations when dealing with each component.
can't wait to hear it's first start after the rebuild.
yep another great video nice attention to detail on painting. i can tell how much you love your old tractors.
My son and I have learnt so much watching your videos, thank you
I love what you are doing with this engine. I especially liked that you chose to use the original o-rings for the injectors. It reminds me to keep everything during disassembly. You never know if you need them or use them for reference because it's a genuine part.
I love watching everything go back together! Always enjoy you’re videos!!
Me too!
When the paint goes on, it's downhill from there.👍👍❤🚜
Can't wait!!! Can't wait!!!! You are so close!! I am so excited and happy for you.
This whole series of videos has been so enjoyable to watch. Can’t wait to see it come to an end and see it running again.
Nice job Pete! It’s gonna be awesome to hear that tractor start!
That’s a lot of progress Pete, thanks for explaining this so clearly and in such detail.
Go for it Pete. I’m excited to see it when it’s completed.
Congrats!!!!! Nice job closing that one up. Long time coming.
Just received your book. Can’t wait to dive in this evening. Thanks again.
Love the job you are doing on the engine.
Pete is very crafty.
The tractor is looking great. I think I have watched every episode in this series. You doing a great job. Can't wait to see it back together.
Thanks Evan! The Case 630 is up next!
Love these videos. Looks awesome. Can’t wait for the next one. 🚜
This has been a great series. Thanks for the experience.
Your attention to details is amazing.
A great mechanic told me one time to use vaseline on the other side so it could be removed without damaging the gasket. Love your y tube channel
hey pete will be great to hear the MD when you get her fired up !!
Super impressive work as always Pete!
Super exciting to see the progress. I'm about to start working on my Farmall M to do a restoration to.
You are getting it together buddy thanks for sharing I’m putting my seal of approval on the job can’t wait to hear it run
Hey Pete I also live in New York and am a hour away. And I know that you live in New York because I have gone past your farm a couple of times and remembered it in the videos.
Nice to see you are making some headway
Make a CD of this build it is very fascinating. If you ever sell or otherwise pass on this tractor to another, the CD of the build will be cherished.
Wow Pete! Good job! Thanks for sharing!
Looking good. Can't wait to hear her run.
Congratulations for getting to this point. It's been an interesting journey.
That’s a butie, love that I H. Red!
Great way to do it.
Love your video’s 🐔🚜👍
That's a good move, Pete, putting a die on the bolt before cutting it. For those that might not have a die, a standard nut will suffice. Also to keep the stud from turning, a double nut one those threads tightened up and held in the vice will be a good step as well. This is the same technique that you used later in the vid.
It's lookin good!, can't wait to see the finished project.!
Can't wait START UP!!! 😀😀😀🚜
waiting for the first start is so anticipating
Excellent video Pete :) also doing super well job on that motor yes and excellent seen progress it coming!
Just subscribed! Have been following The MD rebuild since the beginning!
Thank you Rudy!!
Pete it looks great...thank you for bringing us along
Hi Pete, really enjoying the MD restoration videos. Do you mind me asking what brand of ratchet spanners you use? Thanks and best wishes from England.
Great job Pete👍👍👍👍
Wow! She’s a real beauty!
Congratulations well done so far.
Tom Weidner in Ohio, love your channel , watch every episode , just finished your book fantastic story God bless and keep up the good work.
Thanks Tom!
Great series. I love your tap and die
Like your videos and love your tractors
Doing a heck of a job! I use the same method for installing valve cover gaskets, seems to work like a charm! Is the valve lash setting specified cold or hot in the manual? I know on a gas M the valve lash is .017" hot. I usually set them to about .019" cold for initial start up.
Love your patience and attention to detail.
You got all of the cool tools! 😏😊
Looking pretty good at this point
Well, it may be frustrating to you, but I am enjoying the journey. Setbacks, they happen, but all I can say is that that engine looks really nice! Please keep going, I am eager to see it fire up for the first time after the total rebuild!
great job. Hope you get a chance to work on it some more. Farming comes first
Been watching all along, very good video
Good job Pete
Thanks Pete. You are a good man.
Awesome job, Pete!! That looks satisfying!
Congratulations on the new milestone!
Good morning.
Thanks for sharing. 🙌🙌🙏☝️👍
2 questions:what was the original reason for removing the pre-cups, and what do you use for paint (does it have hardener)?
TA DA! Can’t wait for the start.
Thanks Pete. Very nice work.
Looks nice. Makes you feel good to clean painting machines. Then the first time you have to hit the mud hole. :0)
oh ...so pretty. good job. good things come to those who wait
She’s looking great Pete!!
When torquing a nut or bolt without a torque wrench, you torque using wrist pounds.
Awesome getting so close!!!
Ain’t nothing finer then a good sharp bastard file!..
Thank you for sharing, much appreciated.
I love watching this project, it gave me an idea to start adding the 8n I’m doing to my channel
Use a crow foot wrench end on a extension oriented to 90 with your torque wrench to torque things you can’t get with a socket.
It looks great!
Looks GREAT Pete!!!!
Looks sensational 👍
Keep up the good work!
Looks awesome Pete been following this built and enjoy your channel a ton!!! you mite pick up a crows foot wrench to adapt your torque wrench if this is a problem you have frequently for those pesky tougher spots when torqued bolts are a issue. Great job pete!!!!
Nothing sexier then a fresh coat of engine paint
Looking good
Pete, When you are looking for something, why is it always in the last place you looked. Hardy hahaha har!
When you retire and turn the farm over to the kids, you can go into the tractor restoration business.
for a simpler life.
It is handy when your seal press will also work as an 11/16 socket in a pinch.
Ha ha!
Easy way to clean treads after a bolt was cut off. file or grind from the bolt head side. it will remove most of the burs. The slight taper will also assist with setting the bolt.