Sorry Oliver, I think I hit the thumbs down by mistake! Great video! You have removed the mystery for me. I LIKE the video. I have a bent shaft to replace. Thx!!!
Great video- I'm having to take a look at my 403 after a E45 error. I have water intrusion into the prop gear half and my circuit board side looked good and dry. What is the part number of the KIT you bought?
Sorry to hear you are having trouble. I just ordered the parts I needed off the website for Pylon II: www.torqeedo.com/us/en-us/products/spare-parts/outboards/ultralight/403/pylon-403/pylon-ii The Gearbox UL (Item number 030-00003) was the main part I needed.
@@eltonwadlow I took my pylon apart but haven't followed up with ordering parts yet, I know my prop shaft had a slight wobble, but the front bearing is also bad I think, and I haven't looked into how to replace that front end component. All my electronics look clean yet, so that part is still good. I might just spring for a new pylon in time.($750).
I ordered the parts I needed off the main website: www.torqeedo.com/us/en-us/products/spare-parts/outboards/ultralight/403/pylon-403/pylon-ii The Gearbox UL (Item number 030-00003) was the main part I needed.
hi Ryan, do you have replace the oring whenever you open the torqeedo or can it be use again. the reason i asked is i want to check the inside of my torqeedo if there is water seeping inside. i had water before getting inside the motor and i had it repaired by torqeedo. thanks
@@allanyoung9987 You will need two: O-RING 70 x 1.5 mm, Item number: 009-00021. www.torqeedo.com/us/en-us/products/spare-parts/outboards/ultralight/403/pylon-403/pylon-ii/o-ring-70x1.5mm/009-00021.html
Good Job and You did it. Thanks the shot.
Sorry Oliver, I think I hit the thumbs down by mistake! Great video! You have removed the mystery for me. I LIKE the video. I have a bent shaft to replace. Thx!!!
glad it helped!
Great info thanks
Glad it could help
Great video- I'm having to take a look at my 403 after a E45 error. I have water intrusion into the prop gear half and my circuit board side looked good and dry. What is the part number of the KIT you bought?
Sorry to hear you are having trouble. I just ordered the parts I needed off the website for Pylon II: www.torqeedo.com/us/en-us/products/spare-parts/outboards/ultralight/403/pylon-403/pylon-ii
The Gearbox UL (Item number 030-00003) was the main part I needed.
I’m having the exact same issue.. what’d you find out if you don’t mind me asking?
@@eltonwadlow I took my pylon apart but haven't followed up with ordering parts yet, I know my prop shaft had a slight wobble, but the front bearing is also bad I think, and I haven't looked into how to replace that front end component. All my electronics look clean yet, so that part is still good. I might just spring for a new pylon in time.($750).
Where does the water from the Toqeedo motor go in? Is it the O-ring part? Or is it the propeller part?
A failure at either location could allow water to get in and damage the motor unit
We’re can I buy the new gear box?
I ordered the parts I needed off the main website: www.torqeedo.com/us/en-us/products/spare-parts/outboards/ultralight/403/pylon-403/pylon-ii
The Gearbox UL (Item number 030-00003) was the main part I needed.
hi Ryan, do you have replace the oring whenever you open the torqeedo or can it be use again. the reason i asked is i want to check the inside of my torqeedo if there is water seeping inside. i had water before getting inside the motor and i had it repaired by torqeedo. thanks
I suspect it could be reused, but I would replace it since it is a low cost but critical part
@@drwillingham Thanks buddy!
@@drwillingham Btw, do you know the part number of the o-ring and where do you order your parts? Thanks for the tremendous help.
@@allanyoung9987 You will need two: O-RING 70 x 1.5 mm, Item number: 009-00021. www.torqeedo.com/us/en-us/products/spare-parts/outboards/ultralight/403/pylon-403/pylon-ii/o-ring-70x1.5mm/009-00021.html
Bro I would have put some silicone grease in the Orings... good job showing us❤
Why not just replace the seal?
The drive shaft was broken and needed to be replaced
@@drwillingham I mean instead of the whole housing? Just replace the seal in the housing?
@@andypag1071 oh, yes probably, but the only parts I could find at the time included the whole kit