How to Replace Outside Door Handle 08-12 Jeep Liberty

Buy Now!
New Exterior Door Handle from 1AAuto.com 1aau.to/ia/1ADHE00544
Door handles, especially the driver side, withstand daily abuse. It’s no wonder one might wear out or even break off eventually. TRQ door handles are precision engineered to fit your vehicle perfectly. This video shows you how to install a new TRQ door handle on your 2008-12 Jeep Liberty.
• Check here for more videos on the 2008-12 Jeep Liberty: • Jeep Liberty 2008-2012...
This process should be similar on the following vehicles:
2008 Jeep Liberty
2009 Jeep Liberty
2010 Jeep Liberty
2011 Jeep Liberty
2012 Jeep Liberty
Tools you will need:
• Phillips Head Screwdriver 1aau.to/okU/1AXAA00013
• Pocket Screwdriver
• 10mm Socket 1aau.to/oiW/1AXAA00017
• 8mm Socket 1aau.to/oiW/1AXAA00017
• Trim Tool Set 1aau.to/odt/1AXXX00006
• Complete Torx Bit Set 1aau.to/obM/1AXAA00008
• T27 Torx Driver
• Ratchet 1aau.to/omD/1AXAA00016
• Drill
• Painter's Tape
• Magnet - Extendable
Subscribe: / @trq
Check out our playlist:
Jeep Liberty 2008-2012 2nd Gen KK: • Jeep Liberty 2008-2012...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*

[@cowza10]

Really can't thank you enough! My mom's passenger door handle got stuck in and this video helped me remove it and uncompressed the button. Was able to lube up the spring and make the handle like new again! Thank you for taking the time to make this video and very easy and simple to follow! ♥️

[@yoannybatista4202]

Thank you very much! They wanted almost $300 at the shop to replace the power door lock actuator for my 2001 nitro. I bought the part online and did the job myself in a couple of hours. The process of taking things apart in this video helped me a lot.

[@chuckmayoification]

Very helpful video, thanks for posting it! The book shows the latch mechanism remaining attached to the carrier plate during removal, but I hadn't been able to find a video showing how that looks until I found yours. Cheers!

[@TRQ]

+@chuckmayoification Thanks for watching our video! 1aau.to/m/Shop-TRQ

[@brett8074]

Bro, i did one of these yesterday and instead of leaving the window regulator on the panel i went and took it off 😂😂. It was trial and error, the wire cables for window tracks came off of the roller piece of the regulator, but after almost 2 hours i was able to figure out how to tie those cable wires back up to the regulator and put everything back together, it was tricky as hell.. my aim was to get the lock out, to decode it, everything went successfully, but im glad i learned something new, even if it was the hard way, i just wish I had watched this video first.

[@haithamali152]

thank you so much

[@brohdaw]

I was fixing the window regulator and I don’t know if I put it back together wrong or if the handle is also broken but I must have put the child safety on also. The door will now not open and the outside handle will not work. I see a silver paddle-like mechanism and a curved metal bar with red “guided” plastic around it that seem to have no purpose like I missed something. I don’t know. Or like I said, it could also be broken. But I did switch the child safety and it had done the same thing but after a few tries I could get it open. (Btw after installing a used regulator from a salvage yard that broke again after three times. Either from the rust or the car remaining open or I didn’t plant the window in correctly as you said - wish I had seen your video first. 1 I thought I had better be careful with the glass and 2 I don’t have much strength, that plastic is pretty strong. This has been PITA!!!!). Anyway mine is a 2010 Jeep Liberty, seems different than what you have here in the video but somewhat similar too but I didn’t see you really attack anything. This video is 2 years old so I’m not sure I can get any answers/help.

[@cakins08]

Would it be possible to just drill some access holes to those nuts holding the handle on?

[@patriciaanderson5799]

Good to no how to do it ur self save u money

[@mazebaza3670]

does this work for a dodge nitro 2011

[@randykowerko8848]

do a rear door on a 14 liberty

[@mafoamikaele4324]

I can’t seem to get the glass lock knob of the glass window on my dodge nitro

[@oldpolak5203]

What a crappy design

[@AndreBarnett]

So much agreement