Chainsaw Clutch replacement

Поделиться
HTML-код
  • Опубликовано: 24 дек 2024

Комментарии • 39

  • @cottydry
    @cottydry Год назад +1

    Beating on that clutch looks like it could break some expensive clutch parts or maybe even damage the bearing or seal. Maybe I'm paranoid but I think I'll order the special 3 prong service tool and use an impact. Do you know if manufacturers use Lok Tite on these parts? Do you think it would have been easier with a little heat surrounding the shaft? Thanks for the video.

  • @-DAMPOKHTAK-
    @-DAMPOKHTAK- 8 месяцев назад +1

    بسیار عالی، ممنون از راهنمایی شما. 🙏🙏🙏

  • @wullierennie3190
    @wullierennie3190 4 года назад +1

    Have u any videos on how to replace a clutch on a ht131 pole saw

    • @dmgladden
      @dmgladden  4 года назад

      No I don't have one sorry

  • @rubybrady7051
    @rubybrady7051 3 года назад

    Is it common for clutch spring to break as mine broke after an hours work of new saw

  • @kingpnk
    @kingpnk 2 года назад

    What is the brand of this chainsaw ??

  • @83rdo389
    @83rdo389 3 года назад

    My rope got stuck in the cylinder and I didn’t double knot it. Any ideas how I can get it off?

    • @Darisumer5394
      @Darisumer5394 3 года назад

      Me 2 bro my rope got stuck in the cylinder

    • @83rdo389
      @83rdo389 3 года назад

      @@Darisumer5394 I figured out to just push down or hammer down the cylinder to loosen the rope

  • @wisdom1867
    @wisdom1867 3 года назад

    Why do clutch has to be changed?..I see the old one good condition...Just wanted to know...

    • @dmgladden
      @dmgladden  3 года назад

      When using it was very easy to stop the chain in the tree

  • @gangster_mkd_
    @gangster_mkd_ 3 года назад +1

    Good job man
    Thank you 👍👍

  • @PopaAlexandru.
    @PopaAlexandru. 4 года назад +2

    With an angle grinder wrench it would work faster and better.

    • @dmgladden
      @dmgladden  4 года назад

      Never tried that

    • @johnphilipjones1330
      @johnphilipjones1330 3 года назад +3

      @@dmgladden You must try this method it works so much better than a hammer & cold chisel.

    • @cottydry
      @cottydry Год назад

      Angle grinder wrenches are 2 prong. This clutch design needs a 3 prong tool.

    • @PopaAlexandru.
      @PopaAlexandru. Год назад

      ​@@cottydry Theoretically, it requires a key with 3 claws, practically it works well with 2. And above all, it is preferable to use a key than to hit a brittle cast steel with a hammer. Repairing this clutch if it breaks costs $1, but the Echo costs more (for example).

  • @tomtam558
    @tomtam558 3 года назад

    Hi. Can you make a diy chainsaw trencher

    • @dmgladden
      @dmgladden  3 года назад

      Whats one of them?

    • @tomtam558
      @tomtam558 3 года назад

      @@dmgladden stoked that you replied! Terra trencher or geo ripper.

    • @dmgladden
      @dmgladden  3 года назад

      @@tomtam558 Hi Tom I try to always reply, now your just adding to my ignorance what is that I don't understand a word lol sorry

    • @tomtam558
      @tomtam558 3 года назад

      @@dmgladden lol! Those are brands of hand chainsaws that can dig a ditch.

    • @dmgladden
      @dmgladden  3 года назад

      @@tomtam558 so what would be a "Diy trencher" ?

  • @tristanallen2640
    @tristanallen2640 4 года назад

    is that a universal clutch?

    • @dmgladden
      @dmgladden  4 года назад

      All I know is it's the same as was in mine

  • @whitefox9
    @whitefox9 2 года назад

    Its not coming off so easy as you were insinuating at first
    Maybe you should have used the cold chisel like you said and not pin punches

  • @SekadarPendapat
    @SekadarPendapat 4 года назад +1

    Better use impact wrench

  • @michaelwade7850
    @michaelwade7850 4 года назад

    i know not to throw the chain saw then it stop run due the clutch cheers

    • @dmgladden
      @dmgladden  4 года назад

      Hi again Michael hope your all keeping well and safe, glad you liked the video

  • @rodneylongdike8219
    @rodneylongdike8219 4 года назад

    How do you how do you

    • @rodneylongdike8219
      @rodneylongdike8219 4 года назад

      How do you change stud bolts tighten the bar down on chainsaw

    • @dmgladden
      @dmgladden  4 года назад

      @@rodneylongdike8219 with a box spanner

  • @dailystruggle2762
    @dailystruggle2762 2 года назад

    Im sorry for the loss of your wife..

    • @dmgladden
      @dmgladden  2 года назад

      Where do you get this information

  • @SekadarPendapat
    @SekadarPendapat 4 года назад

    Cheap chinese chainsaw but worthy

    • @94SexyStang
      @94SexyStang 4 года назад

      pfft......JUNK. I would never put my life behind that thing....crappy thin plastic, and a chain spinning 10,000RPM, what could POSSIBLY go wrong???

    • @ahmedm6041
      @ahmedm6041 3 года назад

      Or better yet get a Japanese Makita chainsaw!