From the wood, don’t forget to grease the needle bearings there’s 6 or so in addition to the thrust bearings you greased, mine were completely dried out. FYI the setting for tightness of the roller drive belt is 1mm between the back of the chain idler and the other loop of the chain. It is adjusted by lowering the planing table to 90mm (gives access to both of the inside bolts that lock the roller drive mechanism )slackening off two 13mm bolts, once loose raise and place the belt that done, to tension, insert a screw driver between the bottom of the middle chain drive cog and the aluminium drive and levering downwards until a 1mm gap appears between the sprung idler and the chain then nipping up the bolts, it’s a bit of a phaf to access the bolts as the inside table is in the way. Chain is like a push bike chain and has a removable link, but you managed:)
Heed my advice and get whatever part you can now, not later. Think of it this way, even if you sell this unit before you get to use them, you can price it up a bit to recoup by selling replacement parts with it. So it's a win win. I've found myself in the unpleasant situation where i either had to use old parts (in better condition than i had) or had to order them made. Cheers!
hi, i just got the hms 260, which is either the same or very similar. i cant find a manual though, does anyone know how to adjust the top bed for "jointing". any info would be great. it either doesn't work or i dont know how it works. cheers.
great Video I have the same machine (didnt relaise I had it since 1985) and need to replace the belt and clean up the top deck and idea where to get the belt, and any hint about cleaning up the rusty top decks would be well appreciated
See the vertical springs? The nuts should be 10mm from the ends. i.e screwed on 10mm with 10mm of thread showing. In the Uk NMA are the distributors and have annotated photocopies parts diagrams with little pearls of wisdom like this
@@FromTheWood Obrigado de qualquer forma, já agora tenho mais uma questão eu tenho o modelo HMT-260, comprei já usada, mas não tem esse manipulo que está na engrenagem, ele serve para o quê?
Hi, please help me out, i Have the exact same problem with mine, can You Tell me from where You got the replacement parts? Can You please give me link from where I can buy them? Or the n-am of the shop?
I’m just about to change the rollers on my Scheppach very good timing for me. Can I ask where you had the drawing from. It would be a good idea for me to get on for the rollers before I start. Thanks for the video much appreciated.
I just fixed my machine that had seized rollers (rubber was fine). If you remove the folding side of the table, and take out the cutter head and rollers together, then remove each roller carriage they will come apart after WD-40 and some muscle. Sandpaper removed rust/grime, and I had wax too lubricate. Leaving this here as very little online about this machine. Thanks for the video, used it to see how chain went back on!
put some lubrication on the chain. Either some grease or, if you want a dryer lubricant, take the chain off and soak it in hot candle wax for 20 minutes then let cool and reinstall. This is the "old school" dry lubricant for bicycle chains.....or use a modern dry spray lubricant for modern "new school" bicycle chains ... I would just use a little grease worked into the chain and then wipe off the excess with a rag. Looks good !
Hello good afternoon. Excellent video especially for lay people. I'm an amateur. Carpentry lover. I now had the opportunity to buy such a machine. To make this intervention can you tell me where I can buy this parts kit? Best regards AMendes Hallo guten nachmittag Hervorragendes Video speziell für Laien. Ich bin ein Amateur. Zimmerei Liebhaber. Ich hatte jetzt die Möglichkeit, eine solche Maschine zu kaufen. Können Sie mir sagen, wo ich diesen Teilesatz kaufen kann, um diesen Eingriff durchzuführen? Grüße AMendes
I don’t suppose anyone knows of website where I can buy the whole roller feed gear assembly for a scheppach hms 260? It would be really helpful if anyone could point me in the right direction. Cheers
you can get nearly all the parts for replacement from the producer.............there are still some old guys in the company.....they know the machines HM 0, HM 1, HM 2, HMC 2600 and HMC 3200 from there first days........check it ............... www.scheppach.com/Ersatzteilbestellung.aspx#ersatzteillisten
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
Thanks so much for taking the trouble to post this. Really helped me.
From the wood, don’t forget to grease the needle bearings there’s 6 or so in addition to the thrust bearings you greased, mine were completely dried out. FYI the setting for tightness of the roller drive belt is 1mm between the back of the chain idler and the other loop of the chain.
It is adjusted by lowering the planing table to 90mm (gives access to both of the inside bolts that lock the roller drive mechanism )slackening off two 13mm bolts, once loose raise and place the belt that done, to tension, insert a screw driver between the bottom of the middle chain drive cog and the aluminium drive and levering downwards until a 1mm gap appears between the sprung idler and the chain then nipping up the bolts, it’s a bit of a phaf to access the bolts as the inside table is in the way.
Chain is like a push bike chain and has a removable link, but you managed:)
I have the same machine. It is fine for now, but your video could be usefull for me one day. Who knows. Thank you. I'll save this one.
Thank you
Heed my advice and get whatever part you can now, not later. Think of it this way, even if you sell this unit before you get to use them, you can price it up a bit to recoup by selling replacement parts with it. So it's a win win. I've found myself in the unpleasant situation where i either had to use old parts (in better condition than i had) or had to order them made. Cheers!
Excellent work, and it seems the shop manager approves too. @1:08
Truth. I had not even noticed. Thanks
That was clearly due for replacement. What a difference between the old and the new. Greetings
You can see at 3:08 the comparison between the old and the new pulley. The old wheel has its teeth all worn and crooked.
@@FromTheWood i know that was what i'm talking about. Sorry for my english i normaly speak dutch hahahaha
OK fine. No problem. I also can not be understood well.
I speak Portuguese and not English
@@FromTheWood ok are your from portugal? i'm from Belgium!
Yes I am from Portugal.
Good job!
what is the reference of the yellow strip? Thank's
magnificas recordações dessa menina que nunca nos deixou ficar mal, bom trabalho mestre
Where can I get that spare wheel?
hi, i just got the hms 260, which is either the same or very similar. i cant find a manual though, does anyone know how to adjust the top bed for "jointing". any info would be great. it either doesn't work or i dont know how it works. cheers.
Patient revived. Well done. 👍 👍 👍
Martin Wolf
great Video I have the same machine (didnt relaise I had it since 1985) and need to replace the belt and clean up the top deck and idea where to get the belt, and any hint about cleaning up the rusty top decks would be well appreciated
www.ebay.com/itm/Scheppach-Antriebsriemen-Flachriemen-Vorschub-HMC-HMT-260-05012111/163660650906?hash=item261aef599a:g:HBwAAOSwQd5czFRV
Any chance you could talk us through setting up the roller pressure ?
See the vertical springs? The nuts should be 10mm from the ends. i.e screwed on 10mm with 10mm of thread showing.
In the Uk NMA are the distributors and have annotated photocopies parts diagrams with little pearls of wisdom like this
@@Grahammon You sir, are a treasure, thank you
Boa tarde, Obrigado pelo vídeo de demonstração. onde consegui encontrar as peças para substituir?
Mandei vir pela internet, mas já não me lembro do site.
@@FromTheWood Obrigado de qualquer forma, já agora tenho mais uma questão eu tenho o modelo HMT-260, comprei já usada, mas não tem esse manipulo que está na engrenagem, ele serve para o quê?
Hi, please help me out, i Have the exact same problem with mine, can You Tell me from where You got the replacement parts? Can You please give me link from where I can buy them? Or the n-am of the shop?
I think on Amazon or eBay. I AM on vacations i have not the link
É sempre bom fazer um bela manutençao nas ferramentas de trabalho.
Hi , good job , where u bought all parts?
I’m just about to change the rollers on my Scheppach very good timing for me. Can I ask where you had the drawing from. It would be a good idea for me to get on for the rollers before I start. Thanks for the video much appreciated.
I do not remember. But researched: Scheppach manual thicnesser kombi h2
@@FromTheWood Thanks for replying.
I just fixed my machine that had seized rollers (rubber was fine). If you remove the folding side of the table, and take out the cutter head and rollers together, then remove each roller carriage they will come apart after WD-40 and some muscle. Sandpaper removed rust/grime, and I had wax too lubricate. Leaving this here as very little online about this machine. Thanks for the video, used it to see how chain went back on!
put some lubrication on the chain. Either some grease or, if you want a dryer lubricant, take the chain off and soak it in hot candle wax for 20 minutes then let cool and reinstall. This is the "old school" dry lubricant for bicycle chains.....or use a modern dry spray lubricant for modern "new school" bicycle chains ... I would just use a little grease worked into the chain and then wipe off the excess with a rag.
Looks good !
The chain has not stretched hey...? Do not replace it...?
Hello good afternoon.
Excellent video especially for lay people.
I'm an amateur. Carpentry lover.
I now had the opportunity to buy such a machine.
To make this intervention can you tell me where I can buy this parts kit?
Best regards
AMendes
Hallo guten nachmittag
Hervorragendes Video speziell für Laien.
Ich bin ein Amateur. Zimmerei Liebhaber.
Ich hatte jetzt die Möglichkeit, eine solche Maschine zu kaufen.
Können Sie mir sagen, wo ich diesen Teilesatz kaufen kann, um diesen Eingriff durchzuführen?
Grüße
AMendes
Boa manutenção patricio, eu desmonto, mas não sei se remonto....😁, parabens, saudades dos trabalhos em madeira, abraços
Very good
I don’t suppose anyone knows of website where I can buy the whole roller feed gear assembly for a scheppach hms 260? It would be really helpful if anyone could point me in the right direction.
Cheers
www.powertoolspares.com/scheppach/hm2.m/hm2/accessories.
Try these Blake they have 3 gears listed !
I noticed the bearing in the clutch wheel was noisy? Remove the key from keyway + circlip the bearing presses out carefully (6004) Ebay £3.50 👍
I haave jest realized that I don't have the belt to run the runner rollers from the motor.... lol thanks
My adventure with woodworking started with Stodoys.
you can get nearly all the parts for replacement from the producer.............there are still some old guys in the company.....they know the machines HM 0, HM 1, HM 2, HMC 2600 and HMC 3200 from there first days........check it ............... www.scheppach.com/Ersatzteilbestellung.aspx#ersatzteillisten