Drum Bung Removal with Screwdrivers
HTML-код
- Опубликовано: 16 сен 2024
- Made this for a customer and upon further youtube searching I could not find a similar video. So if you need to remove a bung and do not have the proper tool or an ill fitting tool this might be helpful for you.
3 years ago and still helping thank you.
Thank you! This is how instructional videos should be presented, straight to the point and actually works! Nowadays most instructional videos are filled with too much blah-blahs only to end up not being helpful at all.
This absolute legend just saved me the $20 on a wrench I'd use exactly twice!
Nice! I thought it was something "right under my nose" in a way. Got 30 liters of ethanol I need for the lab but of course nobody bothered finding those tools to unlock them with. But I do have screwdrivers and non-tools that are similar. Good to see it demonstrated to avoid some potential messy mishaps.
Nice tips. Couldn't have open the drum without ur video. I dont have the proper wrench.
4 years ago and still helping.... I must say u made it look like the threads were all buttered up
Thank you, i wanted to see what is the correct tool, and the DIY way. Short and fantastic.
I work in a sheet metal fabrication shop, and use 50 gallon drums of spray glue. I use a Stanley Wonder Bar to remove the bung. Any pry bar about an 1-1/2" to 1-3/4" wide should do as it only needs to contact one of the inside tabs. The other edge will brace against the bung. Just stick in the bent end, twist, and the bung spins out easy, peasy, no 2 handed coordination required.
Awesome!!! I was struggling for a hot minute!😅
Me too
Thank you !
This video was just what I was looking for.
Thanks for that - I couldn't have managed without it today.
Dude an actual fucking life saver
Fantastic. Thank you. You’ve just solved a potentially expensive problem
Thanks bbro im from Indonesia
what a beast this was mad helpful thank you big dawg
Worked like a charm!!! Those people who gave you thumbs down can suck it!!!
Thank you saved me so much time.
Thank you so much for sharing your experience. ❤
Thanks for your video.
It was really helpful
thank you, i knew someone would have a "better" solution.
Dude just became my hero
Awesome and direct to the point!!
Concise. Perfect 👌🏾
Not all hero’s wear capes 👍🏼
Now I can get into my bung hole - thanks!!
Can you do the other small cap too? I have no idea how to open it except for with a pipe wrench, I always end up stripping it. :(
Thank you. I was stuck with one of them, wondering how to open it
Genius! Huge life saver! Great solution.
Thanks 😊 philip
Thank you, exactly what I needed.
Very helpful. Didn't work out for me, but still helpful.
Thanks for the help! I really needed it! Great method!
Thank you 🎉
This just totally saved my A%* - thank you!!
Thank you! This was very helpful!!
So helpful. Thank you.
You. Are. A. Legend.
Thank you!
That's the bung plug. How do you remover the actual bung on the lid?
If you are referring to the bung cover, if metal, i usually grab one of the tabs with pliers. I like to pinch the tab horizontally and then put away from the bung, then up, then across. I find it easiest to use channel locks to make sure the doesn't sliver off. If that happens then you will need to use larger needle nose pliers to just brute force rip it of.
now i know where the term bung-hole is from :D
Uh huh huh huh huh huh...
Worked GREAT, thank you!
Thanks so much
Muito boa ideia
Ty
brilliant
Thanks boss
Great tip
So... what if I have no screw driver???
Thank you
Hell ya this video saved my ass 😂👍🏼
What about the small vent cap? How do you remove it?
Apologies for the late reply. Depending on how tight the bung has been torqued you will require different tools. If it has been torqued to hazmat shipping specs you will need a legitimate bung opening tool. If it is just a general tight I have used large sized channel locks to loosen that bung. Normal pliers will not be large enough. If you go this route make sure the thickness of the channel locks is close to the opening size of the bung.
Thank you!!!
Genius
Wow thank you so much!
Thank you! Did not want to invest in the tool!
My man.
You have served RUclips well. Or me at least
I love you thank you
Helpful 😛
God’s work
If you have heavy duty gloves you may want to wear them I got a minor cut nevertheless be prepared!
omg thank you!
Baaaammmnn!!
Thank you 😂
Bung bandit.
Thanks to you!! I made it hahahahah 😆
🫡