How to replace a kitchen tap part 3: fixing your new tap
HTML-код
- Опубликовано: 8 окт 2013
- Update: Our HomeFit service will no longer be available from the 9 July 2018. Any existing orders will be honoured until 14 December 2018.
Even though it’s no longer available, we still offer a great kitchen, bathroom and bedroom range. We’d love to help design your dream room too, so visit your local store and speak to a member of our team.
Watch our step-by-step video showing how to replace a kitchen tap, with expert advice and top tips to help you complete the job with confidence.
See the other part in this series:
Part 1: Preparing Your New Tap
• How to replace a kitch...
Part 2: Removing Your Old Tap
• How to replace a kitch...
Visit the official B&Q RUclips channel. Here you'll find the ideas and know-how you need to make your home improvement dream a reality: / bandq
Need a helping hand with your DIY project? We're always uploading new videos, so whatever your project, we're here to support you 24/7. Subscribe today so you don't miss out. ruclips.net/user/subscription_c...
For more advice go to www.diy.com/advice
To shop at B&Q go to www.diy.com
Join the B&Q Club for exclusive offers: www.diy.com/club
Like us on Facebook: / bandq
Follow us on Twitter: / bandq
Be inspired on Pinterest: / bandq
Find new ideas on Instagram: / bandq_uk - Хобби
Made up with myself by following these videos I have managed to fit my kitchen tap woo woo!!! So easy to follow thank youuu
Woohoo, that's wonderful! Well done, we're happy to have been able to help! :)
All three vids very clear and confidence building for an amateur like me
Thank you very much guys, I just replaces my tap and felt good, makes me feel confident and independent as woman :)
I'm about to try this...
@@sitnspin1819 how’d it go
@@Alex-jn1ez It went fine! I followed the instructions no bother :)
@@sitnspin1819 thats good my tap’s been leaking around the base and was replacing it soon this was a bit of relief
It makes you a few ££'s richer not paying a plumber. Who in my experience make it sound like rocket science and as difficult.
Beautifully explained 👏👏👏👏👏👏👏👏👏 saved me loads of dosh to spend on other B & Q stuff 👍👍👍
This makes it look so easy! Thank you, the steps are really simple and the instructions are very clear.
Great clear instructions and advice, thank you both
Best Quality tutorial. Thank you.
Great video. Love explanations behind every action
Great tutorial very well presented and explained, Saved me time and money
Thanks so much, we're glad you found it helpful! 😄
Really useful video. Thank you very much.
Great video tutorial from the good shop!
VERY WELL PRESENTED FROM START TO FINISH
OKAY
NO NEED TO SHOUT
This video was so helpful , its not easy to do under the sink , but i managed thank you guys 🙂
I agree wholeheartedly with Des.
Technically the service valve should have a flat faced 1/2" on the tap side, rather than 15mm compression end, to prevent damage to the rubber seal on the tap tails.
Concise and clear. Thank you!
Glad we could help 😊!
Thank you this was very helpful
Thank you I just removed and replaced my new mixer tap😀
Great! Thanks v much- your videos are so clear and helpful. Appreciate it xox
You're welcome! Glad you liked it 🥰
Top tip. Some box spanner sets fit all together to make an extra long spanner that is longer than the sink is deep. This allows you to put the bar through the spanner and get a bit move leverage to tighten the tap in place.
Great tip! 😊
Thanks you best trainer
Why does it take three videos?
Thanks very much, very helpful
You're welcome 😄
Important question here as I’m about to fit one of these. The illustration on the box and the vid here shows the tap on the right hand side. The standard position I guess for right handed people, but my wife is left handed. My question is, can the tap be on the front, so accessible to both hands?
Also, it says it operates 180, but testing it by blowing air into it works 360, my existing tap to be replaced lets water out 360. So no info out there, can it be fitted left, right or centre? Obviously I’m not a pro plumber 😬
Should you use thread tape at the joins?
Cheers gonna use this soon
Great video to follow. Can you please let me know the name of the tool on 0:37-0:43? I need the tool to get my tap fixed firm. Thank you in advance.
It's a Box Spanner
Life saving
V helpful , cheers gents
What is the name of the metal piece he places on top of the rubber piece to ensure the tap stays in place 00:30
It is a horseshoe metal plate, designed to hold on the horseshoe rubber seal, part of a kitchen tap mounting kit.
What do I do if my flexible connections are leaking? I installed them a few months ago following these instructions and attaching my new tap using flexible pipes to the existing isolation valves, similar to the video. However 6 months on they are now leaking from the part I have connected. Should I tighten some more or undo and try valve tape? Then re attach. Any help would be greatly received! Thank you.
Hi there, you may find some useful information on this in the following video. I hope this helps! 😊
bit.ly/3098VVs
@@bandq hi, thank you. However this doesn't help, my flexible connections are leaking not the tap.
Amazing videos.. u guys shud get more likes!! 150K views and only 240likes