Daikin .system 1 ..wall mount ..also error code E6. if on the Aircon , few seconds only compressor and fan running after that not run...will you give good advise.pls
Sir , why it is mentioned three phase on compressor. 380 - 415 Instead of DC. I see on the make compressors it will clearly mentioned dc and frequency range from 70 to 180.
M.Mujeeb don't be confuse in some condenser unit of VRV 3 ,one of the compressor installed is standard compressor,it's not driven by IPM board which is for inverter compressor only.
Hello sir bon. I also encountered that problem but there is no error. The magnetic contactor will engage but I can only hear the standard compressor jam or it's like humming sound. So I decided to replace the compressor . Hope my diagnose is correct
Nice sir because of your videos i learned a lot about trouble shooting thank you and god bless ,, i '' '' m in philippines
Thanks bro.
Help share ya.
Sir Bon do you pump down it or or need to recover the refrigerant while on emergency settings?
Thanks a lot bhon
Thanks
thanks sir Bon
💞
Good job my friend!
Thanks
Nice video sir.
Before you unjoint compressor you pump the freon indoor side or released?
Indoor side
Do you need to vaccuum the lines before powering on the unit after replacing the compressor?
Only CU.
Nice video uncle 👍🏽👍🏽👍🏽
Thanks
👍🇹🇷
In Australia it is illegal to release gas into the atmosphere, Which service port would you reclaim from after closing service valves?
What reading inverter compressor when faulty ??
Check other video got show
Great video. Can you make more videos using Bluetooth D checker?
Thanks
No problem
@@BonMj Bon do you recommend Bluetooth checker for commercial applications? People say you can’t command coils on or off through app.
@@epicone2449 Bluetooth checker is good but expensive.
@@epicone2449 yes ,cant on and off through app
How to set vaacum mode in vrv 3 and when set vaccum uses share plz
Daikin .system 1 ..wall mount ..also error code E6. if on the Aircon , few seconds only compressor and fan running after that not run...will you give good advise.pls
Check power supply voltage, may compressor or pcb faulty
nice sir
Thanks
@@BonMj Welcome Sir
Sir , why it is mentioned three phase on compressor. 380 - 415 Instead of DC. I see on the make compressors it will clearly mentioned dc and frequency range from 70 to 180.
This is 3phase compressor
M.Mujeeb don't be confuse in some condenser unit of VRV 3 ,one of the compressor installed is standard compressor,it's not driven by IPM board which is for inverter compressor only.
Bro vrv iv error code f4 -04problem all light blinking cheng EEV but problem is not solve ,how many problems....???please Reply Bon sir
Please check indoor EEV.
May indoor EEV not functioning well
My friend.. Mitsubishi vrv city multi error code 7117.what is tha problem pls tall me
Check control pcb to inverter pcb connection any loose.
Or one of the pcb faulty
Plz making a video with subtitles plz
How much HP LP setting please tell me
VRV 3
Normally LP=100 to 120, HP=380 to 400psi
@@BonMjvrv3 standard one compressors faulty conturul pcp this setting compressor change ges recover peping how much setting
@@expertair8641 single CU or multi CU
Single CU is set 19 times
Sir How to find out how many hp
By model
@@BonMjsir give me 1example plz
@@mdafsarkhan9278 RXQ10AYM =10HP
@@BonMj thanks sir
@@mdafsarkhan9278 welcome
Hello sir bon.
I also encountered that problem but there is no error.
The magnetic contactor will engage but I can only hear the standard compressor jam or it's like humming sound.
So I decided to replace the compressor . Hope my diagnose is correct
Idu all light blinking
Outdoor blinking F4-04 but sometimes cu still working