Quansheng UV K5 Output Power Test - Stock vs Egzumer

Поделиться
HTML-код
  • Опубликовано: 11 дек 2024

Комментарии • 38

  • @ugsisr
    @ugsisr 8 месяцев назад +2

    On below 2 meter and above 70cm my Quansheng with Egzumer Ver 0.22 performs the same...Higher output on Medium then High... For Operation, I did find out a diamond Dual Band Antenna makes a big difference Thank You

  • @sihartgroves7549
    @sihartgroves7549 Год назад +7

    Excellent, if basic, information: It suggests that no UHF alignment tests were carried out prior to shipping - but, without a spectrum analyser, it’s impossible to be sure how much of the indicated power out was actually at the fundamental frequency and how much was contained in harmonics; If nothing else though, it does give a caution re 27MHz - because we know the actual output is only measured in microwatts at that frequency - and therefore the tuned/filtered PA output stage is trying to do something it was never designed for, and all that extra off-frequency wattage has to be dissipated somewhere…

    • @M-P-X
      @M-P-X Год назад

      A few microwatts on 27 Mhz, the rest of the 4 Watts are on the harmonics.

  • @MrBillUp
    @MrBillUp Год назад +7

    There is a video on RUclips where the owner of the UV-K5 did a test on the stock firmware straight out of the box, and got 6 watts High, 4.5Watts Medium and 3 Watts Low. He then flashed the EGZumer firmware and did the test again with very similar results. He then put the stock firmware back on and retested. The figures were awful. H 2.7 Watts, M 2 Watts and L 1.2 Watts. He came to the conclusion that the EGZumer firmware had bricked the power levels on his radio.

  • @Technician4444
    @Technician4444 11 месяцев назад +5

    I suspect if you were to take a dozen of these Radios, line them up and test for Power o/p you would get twelve different readings.
    In reality a Watt or two either way makes little difference anyway, and of course if you're working a local Repeater then no difference whatsoever.
    These are great little rigs, but they are what they are...just fun to play with.

  • @janhenkins
    @janhenkins 11 месяцев назад +1

    Hello Ben, I love your videos! In order to find the spurious emissions if you TX on the CB bands, you can use something like the TinySA with an attenuator (anything between 10w to 40w) in-line. It's not 100% accurate, but for the money it's a fantastic piece of kit. Combine that with a NanoVNA and you have a very complete set of measurement tools for just about everything in amateur radio. I am very surprised how badly the stock firmware has been calibrated on 70cm, quite shocking really. I have two of these handsets (and one more on the way), the "ugly" K5 and the "pretty" K6 (like yours seen here). It's great to experiment with all these third-party firmware versions, I'll have to give Egzumer a go after this. I like what I see, a 5w HT TX'ing at more than 5w is a rare thing indeed. Cheers! 73, Jan M7HNK

    • @m7frs272
      @m7frs272  11 месяцев назад

      Hi Jan, thanks for your comment. I recently purchased a TinySA and a nanoVNA and I've already done one video with the TinySA. Glad you're enjoying the channel 👍 Ben de M7FRS
      ruclips.net/video/BE2Y7V2tGMM/видео.htmlsi=ln_WMhUKYujjKgNj

  • @heinerrambold8889
    @heinerrambold8889 11 месяцев назад +2

    There should be a power output in the 100-500mW range instead of 2W, 3W or more. I have chinese shortwave trx that also behaves strangely with respect to output. Thanks Ben for the review!!!

  • @DonzLockz
    @DonzLockz Год назад

    Thanks for the tests. I have the power meter. I just need to get a dummy load to test mine now. 73 🍻🤠🇦🇺

  • @quentinbush
    @quentinbush 9 месяцев назад +1

    Thank you for posting this interesting video. I have a question, please tell me how you managed to Tx on 27Mhz when it's outside the radios frequencies? All I get is DISABLED and I am using the EGZumer firmware. Thank you.

    • @m7frs272
      @m7frs272  9 месяцев назад +1

      Hi, firstly I've only done this for experimental and demonstration purposes, and as I've mentioned in this and other videos the Quansheng won't really TX any significant power on the 27Mhz band without causing interference on the Airband frequencies. If you need to be able to unlock it for experimental purposes, you need to go into the hidden menu and select 'Unlock All' 10 times for it to work.

    • @quentinbush
      @quentinbush 9 месяцев назад +1

      Thank you.. Appreciating harmonics etc.

  • @la7dfa
    @la7dfa Год назад +7

    Its a bit disappointing to see low power being so high. It would be better if they used 6dB steps. So 5W, 1.25W and 0.3W.

    • @tvelektron
      @tvelektron 11 месяцев назад

      At least the "Low" setting is much to high i think, would like to have it below 1 Watt..

    • @la7dfa
      @la7dfa 11 месяцев назад

      @@tvelektron The new IJV Italian firmware can adjust the level.

  • @Grimberian72
    @Grimberian72 Год назад

    come on guys give him a sub! don't miss any updates/revisions

  • @falcon02012
    @falcon02012 Год назад

    Thank you for the test it is completely the opposite of what ptronix claim, i wonder what the output power on gmrs frequency.

  • @DM-fz3ly
    @DM-fz3ly 11 месяцев назад +1

    I wonder if the EGZUMER could be adjusted to have power like... High=5 Mid=2.5 Low=0.5 ??

  • @g4joe
    @g4joe Год назад

    Well done 👍

  • @dennishilton5365
    @dennishilton5365 Год назад

    Nice video, any chance you can post link for the meter and dummy load please.

  • @kennymurray3249
    @kennymurray3249 Год назад

    its possible to change the power output for the three levels in the service menu of some other firmwares. i lowered mine to make the tx runtime longer in a decent area and not overdrive anything. i set the lowest setting to less than 1 w.. 2.2w and 4.5w

  • @javhans5978
    @javhans5978 Год назад

    The firmware you flashed the version STOCK 0.26 is not the newest and it's know for a low power output. Try using the latest version for uvk6 V3.00.15.bin or better with the UV5R RT600_v4.00.06_publish.bin . You can compare too firmware_IJV_V2.5.bin with egzumer_v0.20.1.packed.bin for a better comparison ;)

  • @Rylisa24
    @Rylisa24 Год назад +2

    Can you make a video how to fix AM airband on Uv k6?

    • @cantcommentonyoutubevids1335
      @cantcommentonyoutubevids1335 Год назад +3

      AM fix is in menu No.56 just turn it on :) Its good

    • @Rylisa24
      @Rylisa24 Год назад

      @@cantcommentonyoutubevids1335 would you recommend to me to buy uv k6?

  • @mertklck
    @mertklck 9 месяцев назад +1

    Hello. Which software works more stable?

    • @m7frs272
      @m7frs272  9 месяцев назад

      My personal preference is the Egzumer firmware.

  • @w.w77
    @w.w77 10 месяцев назад

    How to I select duplex mode so I can accesssbmy local UHF cb radio repeater station? Thanks

    • @m7frs272
      @m7frs272  10 месяцев назад

      Hopefully my other videos may be of help with this: ruclips.net/video/kZ1i7YP05hQ/видео.htmlsi=21hr5BYo8yJQd5AV
      ruclips.net/video/-g7glWEVpdw/видео.htmlsi=FuYlKeA9fV-3KuP0

  • @johndextersantos9541
    @johndextersantos9541 3 месяца назад

    my radio is only transmitting on miliwats only, , not sure what happened but sometimes it will return back to full power then go back to miliwats . . two of my radios are like this and I'm not sure if it is a software issue.

    • @m7frs272
      @m7frs272  3 месяца назад

      I've not experienced that happening. You could try changing the firmware. What frequencies are you experiencing that on? How are you measuring the power output? Thanks for watching 👍
      Ben, de M7FRS

    • @johndextersantos9541
      @johndextersantos9541 3 месяца назад

      @@m7frs272 I use Diamond SX-200 to measure the power output. on VHF it does not even get past through half a watt. I am using the Nunu custom firmware.
      the bands available to us in our country are 145mhz, 325mhz and 430mhz
      Sometimes when i switch back and forth between UHF and VHF the power would suddenly go back to normal. But recently this trick stopped working for me and my radios are now permanently low power.
      Thanks for your videos, DW3HHT

  • @fpvkabo
    @fpvkabo 11 месяцев назад +2

    don't need to id yourself with dummy load and tx'ing?

    • @m7frs272
      @m7frs272  11 месяцев назад

      Very true 😉 Thanks for watching.

  • @johnemmons9087
    @johnemmons9087 11 месяцев назад

    A little disappointed on your assessment of 11 meters. Without proper testing you really shouldn’t speculate like that. Because all the cb hates just join in, and continue the ignorance.
    Other than that, keep up the other great work on this awesome radio!

    • @wonderingworld119
      @wonderingworld119 11 месяцев назад

      Not sure what you think was said, but what we know so far is that in 11 meters the power output in that band in in low milliwatts. But there is 4 watts going to somewhere. Others have shown that these missing watts are throwing up all over the place. And it isn't something you can fix in software unfortunately because the bandpass filters are just not there. The good news is that the chip can do it, so it is just a matter of time before they start making radios with this chip in it specifically for 11m. I think they are cheap enough that most of us would happily buy one for each band if it meant we were going to get the full 5w on the frequency we wanted to use.