Add copper coil in series with the colant and with anf spray water on it to absorb heat power more the coolant temperature. Abd inmerse the coolant in a hea exchanger too
You may not care anymore, but a proper heat sink and fan is more effective at displacing the heat and will certainly achieve better results in THIS scenario. However, If this set up had a radiator for the coolant then that is a different story as it would most likely out perform the traditional heat sink set up in terms of power efficency/performance, but also would result in a higher energy consumption overall.
Es correcto usar un radiador para mejorar tu refrigeración, pero te recomiendo no colocar otro bloque en la parte fría de la celdas; no aprovechas todo el potencial de las celdas; coloca mejor un discipador de alumnio de tamaño mediano para congelarlo.
I'm running 6 Peltier tiles being liquid cooled using a 240mm pc radiator. After a few mins of use, the radiator can't keep up and the Peltier tiles lose effectiveness. Would this solve that problem? Wouldn't the coolant get warm like the water eventually? People pour a ton of money into their liquid cooled pc components. This would be a VERY easy, cheap solution.
I'm thinking about doing something similar to what you explained but I'm thinking of adding a small reservoir tank of water. Between the reservoir fighting to maintain ambient temps and the radiator, I'm hoping to eliminate that issue.
Coolant is only used to increase boiling point of water and prevent rusting but it does not lower your temperature. The heat from radiator needs to be moved away to an environment you don't care about. Like an aircon, you move the heat outside of your house with the use of fans or leave the radiator on the outside. Better is to have a control unit, that switches current to on and off when the cold side reaches lower and upper bounds.
I'd have handled the components while wearing latex or lint-free cotton gloves to avoid getting fingerprints (oily residue) on the pieces that will have the heatsink paste applied.
car coolant itself cant cool the hot side of peltier. you need radiator or heat exchanger to remove heat from hot fuild of coolant. thats how, car engine heat is removed through radiator and transfered to envoiment
I read for longer life you should cycle them on and off every 1 minute. He is ruining them on 20 Amps the maximum current for 4 is 12V 75 Amps or 15V 60 Amps So he is basically running them at 26.7% maximum capacity . it is recommended to run them at 75% or 85% capacity , I cant remember so stick with the lowest until you come across that information. But the higher the wattage the hotter the hot side becomes. Manufacturers claim they will last anywhere between 2 to 5 years but I gather 5 is the max in best case scenario .
As long as the hot side is managed to kept cool under 50-60°c with liquid cooling if u manage to keep them at temps like 32°c it will work more efficiently and will cool down more
Bro i want to know only one thing how much time we can keep it up continuously by using water coolent plz help me to tell can we use it continuously for 12 hours ??
Can we thought the water on surfaces of peltie module .. Because of when we hot temperature in 0 the cooling side more effective ❣️ try on... About your work. Is very impressive ❣️
Dear admin I have carried out this experiment and assembled the same circuit as in the video. Initially, I turned on the circuit at 08.30 WIB to test whether the circuit had a leak or not. However, it hasn't even been 1 day, at around 18.30 WIB when I checked, there was already a leak in the hot temperature flow or the hot temperature exhaust radiator water... I ask for your help with information on what I need to do to continue the experiment. Kiki From Indonesia.
First, you need to determine where the leak is coming from. You should check the areas where you have connected the pipes; you may need to use pipe clips there. If this is not the issue, then you will need to add 2 liters of water with the coolant. When the quantity of water and coolant exceeds 2 liters, this problem should not occur.
Car coolant or bike radiator coolant never works for too long without a radiator and fan, same with a car, it needs fan for removing heat and for bikes, i think while you're riding, air infront will remove heat.
@@THEKEPLERSTORE No problem. Its meant to make up for the fact that the two surfaces aren't perfectly flat. Although its not a great conducter of heat, its much better than air!
@@KillianTwew spot on. You can also get high grade thermal paste used for high end PC CPU's which will help with cooling the hot side of the peltier modules. Perhaps use a small loop consisting of a 240mm radiator and a reservoir from PC watercooling components to aid the cooling of the hot side :)
Hey, how's it possible to ask this idea, is there any negative or problems that can disable the belt during the time period if I make a refrigerator? avails
Bhai aapne 20 amp ki to power supply li hai. Or 4 Peltier 15 amp yani ki 60 amp liye hai to ye 20 amp power supply se jyada hai. Kya ye power supply work karega i m confused plz tell me help me
as a practical mene 20 amp use kia...lekin apko 60 amp is liye recommend kia apko10 Peltiers chalane hain aur long time k liye. so 60 amp is to much better.. aur supply heat bhi nh kregi 60 amp me..
are bhai cool side pr paste nhi lagana tha paste ka use samjho kya hota hai.. hr jagha use nhi hota.. agar ye het abzorb krta hai to cooling b abzorbe krega samjhe
Okay lets assume i wanna build this I go to the store and tell him WHAT gimee those tow playes where water go in and get out cold ?! Whats it cold man NAME PARTS
Super!
hello viewers its a practical video if you want to make this project so you must used 12v 60Amp power supply.
Hi is it possible to plug the peltier cooling system into a wall socket to power it?
@@cyrusboon2842 no sir. please don't do this.
Then how do I power the peltier cooling system?
@@cyrusboon2842 12 volt 60 amp power supply you can use it. if you have 6 amp x4 peltiers you can use 12v (20 - 24 amp) power supply
@@THEKEPLERSTORE these chips use 5 Amp x 12 volts for one chip is 60w so wouldn't 4 chips be 240 watt at 12v to power this ?
that's a very good answere to the heating problem. i like it
♦️♦️Bro please clarify my doubt, is it possible to connect 4 pieces of 12706 peltier module in 20 amps power supply?❓❓
Yes why not 12706 peltier means per peltier is 6 amp
Add copper coil in series with the colant and with anf spray water on it to absorb heat power more the coolant temperature. Abd inmerse the coolant in a hea exchanger too
great information thanks
After making this system i have a question ❓
How many hours coolant can hold heat .. .
Will coolant hot or not ?
Sir need to refill coolant time by time? It's get dry?
How good cooling performance is comparing to fan based solutions?
You may not care anymore, but a proper heat sink and fan is more effective at displacing the heat and will certainly achieve better results in THIS scenario. However, If this set up had a radiator for the coolant then that is a different story as it would most likely out perform the traditional heat sink set up in terms of power efficency/performance, but also would result in a higher energy consumption overall.
Now i got idea for creating DIY Desktop Fridge and Air Cooler which i really really wanted to do
Do Video upload too
Nice job 👍👍👍🙂🤝🤜🤛
excellent presentation
thanks for the good work
thanks brother
Bahi mai laptop ka power supply use kar sakta hu?
Es correcto usar un radiador para mejorar tu refrigeración, pero te recomiendo no colocar otro bloque en la parte fría de la celdas; no aprovechas todo el potencial de las celdas; coloca mejor un discipador de alumnio de tamaño mediano para congelarlo.
thanks for you guiding me
What do you use that on? Car? Or personal cooling? I’ve been thinking about making one for my car, since I have no ac and it’s a small 2 seater
yes, I was thinking about it. we should make it for car cooling. Thanks
I'm running 6 Peltier tiles being liquid cooled using a 240mm pc radiator. After a few mins of use, the radiator can't keep up and the Peltier tiles lose effectiveness. Would this solve that problem? Wouldn't the coolant get warm like the water eventually? People pour a ton of money into their liquid cooled pc components. This would be a VERY easy, cheap solution.
I'm thinking about doing something similar to what you explained but I'm thinking of adding a small reservoir tank of water. Between the reservoir fighting to maintain ambient temps and the radiator, I'm hoping to eliminate that issue.
Coolant is only used to increase boiling point of water and prevent rusting but it does not lower your temperature. The heat from radiator needs to be moved away to an environment you don't care about. Like an aircon, you move the heat outside of your house with the use of fans or leave the radiator on the outside. Better is to have a control unit, that switches current to on and off when the cold side reaches lower and upper bounds.
Good job
কত
OSM. NICE WORK 👌
Good job my friend 👍👍👍
Bohat alaaaa
are u dont have properly wire cutter?
Knowledgeable video
Great job brother, thank you for sharing.
May I get to know the converter model used here?
Isko bike ka oill cooling fit hogaa kya
Maximun cool?
amazing good Idea
bro, may i know the wattage of your power supply?
12v 60amps smps used...must be better result.garranty
Very good
so the heat part of the peltier was -6.6 C?
A radiator from a car would be a good addition, you can buy them for like $30 for a small car
yeah you saying right..i will do it
great idea
@@THEKEPLERSTORE Thank you, and good luck. Car recyclers (or auto wreckers) will likely be cheaper than new parts
@@FletcherHillier where shud we put the radiator
Did you supply voltage for motor pump with different suppliers?
yes
Can i use laptop power supply?
no because mostly laptop supply 20vdc
Makes perfect sense,
Waw soo nice
Hi sir, may I know what's the temperature of coolant keep running after 1 hours ? By the way, u so wise👍👍👍👍👍
same temperature
@@THEKEPLERSTORE if the coolant stays the same temp then there's no need for a radiator or fans correct?
I'd have handled the components while wearing latex or lint-free cotton gloves to avoid getting fingerprints (oily residue) on the pieces that will have the heatsink paste applied.
yes...that is great information
🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣
car coolant itself cant cool the hot side of peltier. you need radiator or heat exchanger to remove heat from hot fuild of coolant. thats how, car engine heat is removed through radiator and transfered to envoiment
Maybe pipe the fluid into a closed bottle buried in the ground or lake or as you say, to a radiator with a fan to dissipate heat.
Nice video sir... Much appreciated.. :)
How long will the peltier last
Sir im connected one peltier at 3amp but not going to low temp why .... What is requirment of amp
what is your Peltier amp ?
@@THEKEPLERSTORE 6amp
@@kryptexgaming5813 ok so you should connect 12v 10 amp power supply
Hi if you put a radiator on both ends Will it work as an ac?
yes why not
Impressive 👍🏻
thanks
How many minutes can the peltier be working continuously with damage??
I read for longer life you should cycle them on and off every 1 minute.
He is ruining them on 20 Amps the maximum current for 4 is 12V 75 Amps or 15V 60 Amps
So he is basically running them at 26.7% maximum capacity .
it is recommended to run them at 75% or 85% capacity , I cant remember so stick with the lowest until you come across that information.
But the higher the wattage the hotter the hot side becomes.
Manufacturers claim they will last anywhere between 2 to 5 years but I gather 5 is the max in best case scenario .
200k hours minimum
As long as the hot side is managed to kept cool under 50-60°c with liquid cooling if u manage to keep them at temps like 32°c it will work more efficiently and will cool down more
Where are you getting these parts?
.
.
Wear this part
AliExpress is a good place to start
online store. like a Amazon
Power consumption??
Why used water or coolant? I have a TEC peltier but don't have a hole for water
You need to have a way to cool down the coolant otherwise you are just using hot coolant over and over
What are the materials in the video?
Peltier's
coolant
aluminum water blocks
power supply
water pump
Bro i want to know only one thing how much time we can keep it up continuously by using water coolent plz help me to tell can we use it continuously for 12 hours ??
Sounds like something is on flowering stage
Nice
how much power this device consume?
12v 24amp
Can we thought the water on surfaces of peltie module ..
Because of when we hot temperature in 0 the cooling side more effective ❣️ try on...
About your work. Is very impressive ❣️
thanks sir
Dear admin
I have carried out this experiment and assembled the same circuit as in the video.
Initially, I turned on the circuit at 08.30 WIB to test whether the circuit had a leak or not.
However, it hasn't even been 1 day, at around 18.30 WIB when I checked, there was already a leak in the hot temperature flow or the hot temperature exhaust radiator water...
I ask for your help with information on what I need to do to continue the experiment.
Kiki From Indonesia.
First, you need to determine where the leak is coming from. You should check the areas where you have connected the pipes; you may need to use pipe clips there. If this is not the issue, then you will need to add 2 liters of water with the coolant. When the quantity of water and coolant exceeds 2 liters, this problem should not occur.
If want 10 peltier in one smps.which amp i can use?
first you tell me your SMPS Amps ? which you have
if you use tech1-12706 peltiers 10 pcs then you should use minimum 12v 60Amp power supply.
@@THEKEPLERSTORE thanks.😊
@@THEKEPLERSTORE i want to buy new
Looks good
So does car coolant help? How long can it work? how much temperature does warm side reach?
yes .....28c
Hi
I've used this but using bike radiator coolant oil. But still it's hot how to troubleshoot that ?
kindly use car coolant.
@@THEKEPLERSTORE what's the difference between bike and car coolant bro
Car coolant or bike radiator coolant never works for too long without a radiator and fan, same with a car, it needs fan for removing heat and for bikes, i think while you're riding, air infront will remove heat.
Sir cable tie not work on water block hot side use another matterial
Great idea! However, maybe less thermal paste... its not meant to be your main source of heat conduction.
thanks! i thought both are responsible for heat conduction
@@THEKEPLERSTORE No problem.
Its meant to make up for the fact that the two surfaces aren't perfectly flat. Although its not a great conducter of heat, its much better than air!
@@KillianTwew spot on. You can also get high grade thermal paste used for high end PC CPU's which will help with cooling the hot side of the peltier modules. Perhaps use a small loop consisting of a 240mm radiator and a reservoir from PC watercooling components to aid the cooling of the hot side :)
Good , but you should first show the temperature of the coolant before peltier ON and after that ,peltier ON reading.
yes noted next time will do it
I can see it used for a raspberry pi4 cluster 8 node with independent cooling blocks for CPU and GPU and memory
yes you can use
Do you need to put ice at a moment in car cooler cause otherwise it will warm no ? Very interesting video thanks for sharing
where we can buy these stuff
online store.. like a Amazon
Simply circulating a coolant wont cool, how r u dissipating the heat from the hot coolant??
what is name of this parts of color .???
coolant
Good idea :)
Hey, how's it possible to ask this idea, is there any negative or problems that can disable the belt during the time period if I make a refrigerator? avails
first tell me which belt you are talking about ?
if you wanna make a refrigerator so should add radiator in this project
Instead of coolant use mineral oil or paraffin oil which has a lower viscosity allowing for more heat to dissipate through convection.
okay it's a great idea thanks
Wow
What are those white bacteria?
heat sink paste
Please provide links for theas item
www.amazon.com/BXQINLENX-Aluminum-Graphics-Radiator-Heatsink/dp/B011QG23J2
www.amazon.com/Diymore-TEC1-12715-Heatsink-Thermoelectric-Cooling/dp/B01JRUNE6U/ref=sr_1_1?dchild=1&keywords=PELTIER+15+AMP&qid=1619860435&sr=8-1
lidigz.en.made-in-china.com/product/CsRmIEklYHcU/China-4L-Green-Color-Anti-Rust-Radiator-Coolant.html
I don't see any reason to use coolant instead of just water? Coolant just has glycol added so it won't freeze in the winter
i was thinking the same. A much bigger tank would dissipate the heat as eventually the small water tank is going to heat up.
Car ke liye pailter ka use kare
You are using 15Amps peltier module, 4 time is 60A. You should use a power supply more than 60A.
yes already I have mentioned on my comments list
Bhai aapne 20 amp ki to power supply li hai. Or 4 Peltier 15 amp yani ki 60 amp liye hai to ye 20 amp power supply se jyada hai. Kya ye power supply work karega i m confused plz tell me help me
as a practical mene 20 amp use kia...lekin apko 60 amp is liye recommend kia apko10 Peltiers chalane hain aur long time k liye. so 60 amp is to much better.. aur supply heat bhi nh kregi 60 amp me..
Radiator and blower needed, reservoir only is insufficient.
Nice:)
এই জিনিস গুলো কোথায় পাওয়া যাবে
Without a radiator it will not run for longer time..
ভাই কেলটাআর এর দাম কত?
Good job brah
thanks
How much time it takes to freeze 100ml of water
it will take 2 hours to freeze 100ml of water
@@THEKEPLERSTORE well then it will make no sense if i use it in a 75litre swamp cooler
C shape water black
It is can make air coller
YES
are bhai cool side pr paste nhi lagana tha paste ka use samjho kya hota hai.. hr jagha use nhi hota.. agar ye het abzorb krta hai to cooling b abzorbe krega samjhe
hmmm great idea
Beneran ga itu?
Where is fan for cooling
no need any cooling fan about this project
Component/ parts name plz I want buy
Okay lets assume i wanna build this
I go to the store and tell him WHAT
gimee those tow playes where water go in and get out cold ?!
Whats it cold man
NAME PARTS
you can easily buy its parts on amazon i have already mentioned the link in description.
You forgot to tell us temprture of coolant 😔
I WILL MENTION ON NEXT VIDEO
আমি এইটি নিতে চাই
Car ke liye ac banay peltiar ka upyog se
ok
Mere paas Maruti 800 hai usme ye material use kar ke ac ka jugaad batao 😇
@@kkcmini hahaha good question...you can use this project just add mini radiator.
Pal taiyar model chahie
I assume you know that car coolant is toxic
Kya banaye kis Kya fayda hoga kuchh To bataya Nahin to kya kya samjhenge log
Car coolant can't cool the car engine...
It just avoid coolant passage from rust ... And easy flow🖕
Kuchh To samajh hi mein Nahin aaya ki kya banaye tum yaar Tumhara project bakwas 🤮
وڈسپ۔نمبر
Nice
thanks bro