The material he is using is alum wiring. Copper is better and will not burn up after welding with it a few times. Aluminum wiring gets hot and will burn up. Thats why they dont use it for electrical anymore
its the other way around, aluminum is a cooling material thats why thats widely used on transformer type welding machine specially to machine with higher rating 600A up to 1500A!
Top demais só que aqui no rio de janeiro não tem trafo desse tamanho fiz um máquina caseira ficou muito boa mas fiz retificada fico top o Sr tá de parabéns.
I'm watching from Russia. Well done master! Well done job! But, not everything is done correctly. 1. The winding wire is aluminum, and the bolts are copper. Copper and aluminum are incompatible galvanically. According to the Rules of electrical installations, direct contact of aluminum with copper is prohibited: it provokes strong oxidation at the junction, which increases the resistivity of the contact, the wiring gets very hot and burns. 2. An isolation must be made between the magnetic circuit (transformer core) and the mounting. It is necessary to make a paper gasket between the transformer core and the steel housing. It is even necessary to insulate the studs (which pass through the transformer iron) with a thin layer of insulation. This is done necessarily, because if this is not done, then the whole metal is galvanically connected and works as one. This creates unnecessary parasitic leads and losses of up to 10-15% occur in the transformer and it heats up much faster and stronger. Its efficiency is falling. 3. Well, the ratio is not the most optimal. And of course, if there is such a possibility, it is better to wind the welding transformer with a rectangular section tire. This is the best option. /I don't know English, I used Yandex translator, maybe not all the translation is normal/ . Смотрю из России. Молодец мастер! Хорошо проделанная работа! Но, не всё сделано правильно. 1. Провод обмотки алюминиевый, а болты медные. Медь и алюминий несовместимы гальванически. Согласно Правилам устройства электроустановок, прямое соприкосновение алюминия с медью запрещено: оно провоцирует сильное окисление в месте стыка, из-за чего растет удельное сопротивление контакта, проводка сильно нагревается и обгорает. 2. Обязательно должна быть сделана развязка между магнитопроводом (сердечником трансформатора) и креплением. Нужно делать прокладку из бумаги, между сердечником трансформатора и стальным корпусом. Нужно даже изолировать шпильки (которые проходят насквозь через трансформаторное железо) тонким слоем изоляции. Это делается обязательно, потому что, если этого не сделать, то весь металл гальванически связан и работает как одно целое. Этим создаются лишние паразитные наводки и у трансформатора происходят потери до 10-15% и он намного быстрее и сильнее греется. Падает его КПД. 3. Ну и соотношение подобрано не самое оптимальное. Ну и конечно, если есть такая возможность, сварочный трансформатор лучше мотать шиной прямоугольного сечения. Это самый оптимальный вариант. /Не знаю английский язык, пользовался Yandex-переводчиком, может не весь перевод нормальный/
Your a good technician ....we learn more within your channel
Excelente trabajo .... Felicidades ... una consulta ...la Bovina del primario para que tencion de trabajo es ??? Gracias ...
Bhai aapne current kaise nikala ?
انتة موهبة صناعية ممتازة👍
The material he is using is alum wiring. Copper is better and will not burn up after welding with it a few times. Aluminum wiring gets hot and will burn up. Thats why they dont use it for electrical anymore
its the other way around, aluminum is a cooling material thats why thats widely used on transformer type welding machine specially to machine with higher rating 600A up to 1500A!
Top demais só que aqui no rio de janeiro não tem trafo desse tamanho fiz um máquina caseira ficou muito boa mas fiz retificada fico top o Sr tá de parabéns.
,
इससे 8 no रोड चला सकते है
लोहा को कटिंग कर सकते है
One of the best videos with best work. Subscribed.
Very Impressive👍🤩
It will be immortal , if u dip it in transformer oil.
Yes, you are right. Thank you.
Bro how did you resulted the. Current 😅???
hello sir, where do you buy those insulated aluminum wire
You are really a talented person.
Thank u sir.
Very good video editing.
Thank you very much!
@@zenithcomputers3286 sir ur contact number please
Can u help me with the dcc wire u have used in welding near my place it is not available
Sir thickness of insulating sheet used in primary &secondary
Core no and stack length in inch ???
Core no-s9 and stack length 5.3 inch.
Boa tarde. Alguém pode me dizer onde eu encontro o material que feito esse carretel?
Great dane wow
Good notice!!!
How?
He should measure short circuit current of secondary coil to improve!!
Amount of current in the output while welding ???
This is pure 100 ampere transformer.
I think it's more than 100 amp use a clamp meter to measure the current i m sure it isn't 100 amps its almost 220 amps according to me
@@sciencefusion5352 esagerato !!! il nucleo in ferro del trasformatore non da kW 8.800 inoltre con 220 amp. il secondario in alluminio fonde 😁😁😁
Sar core kitne no ki h
s9 core h.
Bobin size
How to make tig welding machine at home
Ok I will try
Kor kitne no. H
hi
thankyou for video
are the wires aluminum or copper?
They are aluminum core bro.
Coil is Aluminium or Copper ?
Awesome 😎
Thanks 🤗
@@zenithcomputers3286 you are doing amazing job my frnd
I m also discovering new and awesome ideas for welding transformer from u 😎
Are you also selling
Es una exageración el calibre del secundario
Ya que en corto el trafo da 3 veces más el amperaje que nominalmente trabaja
Nice bro
Thanks
Sir welding mc service training solli kodupigala
Excellent
A man use hot blower for Secondary Winding it will help you to bendthe coil easly.
What a nice short.
00qq0qq
Qq
So nice sir g
What is the price
Indian Eight Thousand approximately
I'm watching from Russia.
Well done master! Well done job!
But, not everything is done correctly.
1. The winding wire is aluminum, and the bolts are copper. Copper and aluminum are incompatible galvanically. According to the Rules of electrical installations, direct contact of aluminum with copper is prohibited: it provokes strong oxidation at the junction, which increases the resistivity of the contact, the wiring gets very hot and burns.
2. An isolation must be made between the magnetic circuit (transformer core) and the mounting. It is necessary to make a paper gasket between the transformer core and the steel housing. It is even necessary to insulate the studs (which pass through the transformer iron) with a thin layer of insulation.
This is done necessarily, because if this is not done, then the whole metal is galvanically connected and works as one. This creates unnecessary parasitic leads and losses of up to 10-15% occur in the transformer and it heats up much faster and stronger. Its efficiency is falling.
3. Well, the ratio is not the most optimal.
And of course, if there is such a possibility, it is better to wind the welding transformer with a rectangular section tire. This is the best option.
/I don't know English, I used Yandex translator, maybe not all the translation is normal/
.
Смотрю из России.
Молодец мастер! Хорошо проделанная работа!
Но, не всё сделано правильно.
1. Провод обмотки алюминиевый, а болты медные. Медь и алюминий несовместимы гальванически. Согласно Правилам устройства электроустановок, прямое соприкосновение алюминия с медью запрещено: оно провоцирует сильное окисление в месте стыка, из-за чего растет удельное сопротивление контакта, проводка сильно нагревается и обгорает.
2. Обязательно должна быть сделана развязка между магнитопроводом (сердечником трансформатора) и креплением. Нужно делать прокладку из бумаги, между сердечником трансформатора и стальным корпусом. Нужно даже изолировать шпильки (которые проходят насквозь через трансформаторное железо) тонким слоем изоляции.
Это делается обязательно, потому что, если этого не сделать, то весь металл гальванически связан и работает как одно целое. Этим создаются лишние паразитные наводки и у трансформатора происходят потери до 10-15% и он намного быстрее и сильнее греется. Падает его КПД.
3. Ну и соотношение подобрано не самое оптимальное.
Ну и конечно, если есть такая возможность, сварочный трансформатор лучше мотать шиной прямоугольного сечения. Это самый оптимальный вариант.
/Не знаю английский язык, пользовался Yandex-переводчиком, может не весь перевод нормальный/
total cost of this project
Bhai total cost
OK, but first, you have to get an old transformer, for exemple, that you will turn..
this transformer for a long time 100 amps will not pull weak wires
Tig welding machine making sir
Mashallaj vnice
شكراً لك
Waist of time. And internet also , nothing is in this video for learning , because only he know what goin on their ,
Excelente
the music is unnecessary
👍👍👍
তুমার মোবাইল no dayo
Disgusting background music. 😡😡
What does that have to do with the project kid?!
😯
only the horible music, nothing to learn what is it for ? His only plan to get money from u Tube
What you want to know? Please type your questions.
Qñqm1p