Thx for the video. Changed out my water pump today with your help. Hardest part was loosening the fan. Had to use a fan removal tool that I rented from the auto part store and I didn’t have a giant wrench. Thanks again. Great detail
I replaced my water pump with a Navistar pump from Diesel O-Rings. I upgraded the thermostat housing and outlet with billet aluminum items from Riff Raff Diesel. Both are great sources for 7.3 parts.
Before I took the fan off I would slide a piece of card board down behind the fan shroud so I didn't gouge the radiator. For me I would need a couple guide bolts when Installing the water pump. Also I've had leaks at the thermostat housing ,after replacing with a billot aluminum housing that cured the leaks. I'm sure everyone has there own procedures but I think you did a great job of explaining what you was doing. Thanks
All that you're replacing the original clamps. I've used those time and time again on European cars. Is there something about the Ford ones that they corrode or something? With the right little tool to undo those they're much faster and more reliable then the hose-eater clamps you were using.
I’ve had them fail several times. Especially ones that are 25 years old and have been removed and replaced several times. Also, up here in the Midwest we get lots of rust to where they rot off… so, going with a new clamp assures that won’t be a problem.
I have a 1997 7.3l. I drained the system last night and got about 5-6 gallons out of it. It drained for about an hour and stopped dripping. When I took off the old water pump about 2 more gallons came out from the engine. Did I do something wrong? Also, if you refill with cap off does that help burp the system?
Sounds like you might’ve just had an air bubble stuck in there that held some antifreeze back. And yes, if you refill the system and then start it up and let it run a while with the cap off it helps get the air out of the system. Then drive around the block a few times going up and down some hills and bring it back home and shut it off and let it sit for about an hour or two to cool down on level and top it back off again. And then drive it for a week and see if it needs anymore.
Cut them old hoses right off and replace them with the new water pump and save yourself the trouble of finding out you should have replaced them all at the same time.
great video. very helpful, but, man, you're totally misusing the word cavitated. Cavitation is basically bubbling in a fluid going through a pump. The rough flow can wear away at the surfaces around it.
@@badsanta518 Cavitation has multiple definitions, including the formation of vapor bubbles in liquids, the wearing away of solid surfaces, and the formation of cavities in organs or tissues: Vapor bubbles in liquids Cavitation is the process of forming vapor bubbles in a liquid at low pressure regions. This can happen when a liquid is accelerated to high velocities, such as in water turbines, centrifugal pumps, and marine propellers. Cavitation can also occur when a high-intensity ultrasonic wave causes gas pockets to expand and collapse, generating high stresses in the liquid. This is known as ultrasonic cavitation. Cavitation can cause structural damage to propellers and pumps, and can sound like a pump is full of gravel, marbles, or rocks. Wearing away of solid surfaces Cavitation can also cause solid surfaces, such as concrete or metal, to pit and wear away as the vacuums in the surrounding liquid collapse. Cavities in organs or tissues Cavitation can also refer to the formation of cavities in organs or tissues, especially during disease. In embryology, cavitation is the formation of the blastocoel, a fluid-filled cavity that defines the blastula or blastocyst.
@@badsanta518 would you rather I waste my time explaining the definition to you in my own words rather than sending the correct definition? Also, erosion is a process or action. It’s not the result. “Eroded” is the result of erosion. You’re batting 1000 tonight. And once again, I used the word “cavitated” or “cavitation” correctly.
Thx for the video. Changed out my water pump today with your help. Hardest part was loosening the fan. Had to use a fan removal tool that I rented from the auto part store and I didn’t have a giant wrench. Thanks again. Great detail
This is hands down the best informative how to video I have seen. Great job and Thanks!!
Your comment is exactly what makes me want to keep making videos. Thank you!
@@thehowardsgarage2480 I just changed my water pump on my 7.3 PSD today. It was easy thanks to you and your video. 🙏🏾
This was an exceptional video. Thank You, sir!
I replaced my water pump with a Navistar pump from Diesel O-Rings. I upgraded the thermostat housing and outlet with billet aluminum items from Riff Raff Diesel. Both are great sources for 7.3 parts.
Both are top notch! Great to do the oil cooler o rings at that same time too.
Before I took the fan off I would slide a piece of card board down behind the fan shroud so I didn't gouge the radiator.
For me I would need a couple guide bolts when Installing the water pump.
Also I've had leaks at the thermostat housing ,after replacing with a billot aluminum housing that cured the leaks.
I'm sure everyone has there own procedures but I think you did a great job of explaining what you was doing.
Thanks
Thank you very much for watching and those are some great tips!
Looking to replace mine this is a good video to start with. Thanks
The best water pump replacement video I have ever seen. Thanks!!!!
All that you're replacing the original clamps. I've used those time and time again on European cars. Is there something about the Ford ones that they corrode or something? With the right little tool to undo those they're much faster and more reliable then the hose-eater clamps you were using.
I’ve had them fail several times. Especially ones that are 25 years old and have been removed and replaced several times. Also, up here in the Midwest we get lots of rust to where they rot off… so, going with a new clamp assures that won’t be a problem.
You've got a new subscriber today bud, thanks
@@gustavopalencia748 thank you sir, I hope you find the information I provide useful
First I want to say thank you very much. What brand coolant, mixed, concentrated, and any additive? Thanks
I have a 1997 7.3l. I drained the system last night and got about 5-6 gallons out of it. It drained for about an hour and stopped dripping. When I took off the old water pump about 2 more gallons came out from the engine. Did I do something wrong? Also, if you refill with cap off does that help burp the system?
Sounds like you might’ve just had an air bubble stuck in there that held some antifreeze back. And yes, if you refill the system and then start it up and let it run a while with the cap off it helps get the air out of the system. Then drive around the block a few times going up and down some hills and bring it back home and shut it off and let it sit for about an hour or two to cool down on level and top it back off again. And then drive it for a week and see if it needs anymore.
Cut them old hoses right off and replace them with the new water pump and save yourself the trouble of finding out you should have replaced them all at the same time.
great video. very helpful, but, man, you're totally misusing the word cavitated. Cavitation is basically bubbling in a fluid going through a pump. The rough flow can wear away at the surfaces around it.
@@badsanta518 Cavitation has multiple definitions, including the formation of vapor bubbles in liquids, the wearing away of solid surfaces, and the formation of cavities in organs or tissues:
Vapor bubbles in liquids
Cavitation is the process of forming vapor bubbles in a liquid at low pressure regions. This can happen when a liquid is accelerated to high velocities, such as in water turbines, centrifugal pumps, and marine propellers. Cavitation can also occur when a high-intensity ultrasonic wave causes gas pockets to expand and collapse, generating high stresses in the liquid. This is known as ultrasonic cavitation. Cavitation can cause structural damage to propellers and pumps, and can sound like a pump is full of gravel, marbles, or rocks.
Wearing away of solid surfaces
Cavitation can also cause solid surfaces, such as concrete or metal, to pit and wear away as the vacuums in the surrounding liquid collapse.
Cavities in organs or tissues
Cavitation can also refer to the formation of cavities in organs or tissues, especially during disease. In embryology, cavitation is the formation of the blastocoel, a fluid-filled cavity that defines the blastula or blastocyst.
@@badsanta518 no offense, and I greatly appreciate you watching the video. But, the word “cavitation” is 100% used correctly in my video.
@@thehowardsgarage2480 yes. you'll see in all those definitions you copied and pasted, cavitation is the action. erosion is the result.
@@badsanta518 would you rather I waste my time explaining the definition to you in my own words rather than sending the correct definition? Also, erosion is a process or action. It’s not the result. “Eroded” is the result of erosion. You’re batting 1000 tonight. And once again, I used the word “cavitated” or “cavitation” correctly.
@@thehowardsgarage2480 your teachers let you down,. eroded is a past tense verb.