Hey, great video as always, could you make a full video on wall settings you use, also which infill, travel speed settings and retraction too please ^^ edit : btw you said in description you enabled zhop, but on all metal hotend and direct drive, it's recommended to disable it (I use micro swiss direct drive on ender 3 v2 neo with brissfang v5 duct, x limit switch moved further to work it, also y limit switch further away too)
Hey, I sure can. Regarding Z-Hop, I do recommend that it's enabled, especially if you're printing above 100mms, without it you can knock down the supports. If you're using the V2 neo with Microswiss direct drive then it could be too heavy to use z hop effectively, the S1 sprite extruder is light weight and has dual Z motors, I found no issues using it.
@@ZeltroixI don't have my desktop turned on to see exactly what settings I've put for z hop in fact, but I believe I must have disabled, I should try to enable it again to see how it goes, I have a second z motor, I've modded a synchronous belt like yours but used bigger gt2 pulley I found on printable (the zip file contains A LOT of different gt2 sizes) to have z axis well aligned but also the 640mm timing belt tightened + all upgrade you have too ^^ (also have anti backlash nuts), but yeah, I'm finishing an 11hrs print and I'll try messing around the settings again if you're willing to share yours too :) ! (I can print at 120mm/s without problem with the microsswiss direct drive and brassfang v5 duct and original extruder motor, anyway, I'll switch to a pancake nema 17 motor to ease the weight, I'll soon go with klipper ^^) I didn't like the creality sprite design because of not so much mods for better cooling even if it's light, usually, the better ducts are the brissfang and the hero me gen 7 with 5050 fans, I'll switch to the light and new microswiss ng extruder with the new gear ratio like the creality sprite, some people modded ducts for it ^^. Btw I switched to V slot metal wheels like you, it solved many of my issues I had with the low quality rubber ones. In the end I think I'll switch to the microswiss ng extruder + linear rail for x and y axis
Gonna try this out on my next print. Thanks for the video!
Hey, great video as always, could you make a full video on wall settings you use, also which infill, travel speed settings and retraction too please ^^
edit : btw you said in description you enabled zhop, but on all metal hotend and direct drive, it's recommended to disable it (I use micro swiss direct drive on ender 3 v2 neo with brissfang v5 duct, x limit switch moved further to work it, also y limit switch further away too)
Hey, I sure can.
Regarding Z-Hop, I do recommend that it's enabled, especially if you're printing above 100mms, without it you can knock down the supports. If you're using the V2 neo with Microswiss direct drive then it could be too heavy to use z hop effectively, the S1 sprite extruder is light weight and has dual Z motors, I found no issues using it.
@@ZeltroixI don't have my desktop turned on to see exactly what settings I've put for z hop in fact, but I believe I must have disabled, I should try to enable it again to see how it goes, I have a second z motor, I've modded a synchronous belt like yours but used bigger gt2 pulley I found on printable (the zip file contains A LOT of different gt2 sizes) to have z axis well aligned but also the 640mm timing belt tightened + all upgrade you have too ^^ (also have anti backlash nuts), but yeah, I'm finishing an 11hrs print and I'll try messing around the settings again if you're willing to share yours too :) ! (I can print at 120mm/s without problem with the microsswiss direct drive and brassfang v5 duct and original extruder motor, anyway, I'll switch to a pancake nema 17 motor to ease the weight, I'll soon go with klipper ^^)
I didn't like the creality sprite design because of not so much mods for better cooling even if it's light, usually, the better ducts are the brissfang and the hero me gen 7 with 5050 fans, I'll switch to the light and new microswiss ng extruder with the new gear ratio like the creality sprite, some people modded ducts for it ^^.
Btw I switched to V slot metal wheels like you, it solved many of my issues I had with the low quality rubber ones.
In the end I think I'll switch to the microswiss ng extruder + linear rail for x and y axis
Discord server link?