How to fix Reduced Engine Power and Service Traction Control on GM Chevy Pontiac Buick
HTML-код
- Опубликовано: 8 сен 2024
- How to fix reduced engine power and service traction control system on your vehicle.
Amazon Links:
Hub Buster: amzn.to/3sXGBU5
My test light: amzn.to/2VCYpak
My scan tool: amzn.to/3JCxrD2
My little scan tool: amzn.to/3H2bWtt
TPMS scan tool: amzn.to/35aYLJN
Tire Machines: amzn.to/2R4mYu6
Torx Socket Set: amzn.to/3By4pSa
Torque Wrench: amzn.to/3scOMg9
Bench Vice: amzn.to/3sTtDXf
Plastic trim tool set: amzn.to/3v3Xy1t
LED magnetic light: amzn.to/3p1q00t
MUST HAVE for coolant work https: amzn.to/3oYinI8
I could tell by his demeanor and his non rehearsed, natural flowing dictation that he has been around the block more than a couple times and is at home doing diagnostics. When ya got experience in an arena it shows. In this case he had several pretty good indications of the issue. But as for the reduced power mode, or message, I've had several impalas in my garage, many things will trigger this cars self preservation mode. The Throttle position sensor, the variable valve timing servo, the accelerator pedal position sensor, the oil pressure sensor, any of the engine wiring harness wires are a huge trouble area in these cars and often over looked (my Impala, 2006 has 168 circuits in that harness) These cars build a huge amount of heat in a very congested area and the insulation will get brittle wires get brittle, shorts and breaks are common and hard to run down. Often times even an intermittent problem, hit a bump the break in a wire separates, hit another bump now its fine kind of thing. Advise is be diligent, start with simple things, as you rule them out move up. Remember that often and more for the older cars those trouble codes are suggestions or suspects, (innocent until proven guilty) . A good digital volt ohm meter is a perfect partner for a scan tool. Check, test, and verify a sensor is bad as much as possible before replacing it. I've seen guys spend $1000 by reading a code, oh I'll buy that sensor, then get another code, well I need that one also and so on, only to bring it to me and learn a connection was corroded. Some of these sensors may have a range of 8 tenths of a volt between good or bad. Good luck to anyone with these issues, just go cautious, stay calm, be methodical, and research means everything.
Titan_363 l
Great comment/info!
what a pain in ass. I changed the gas pedal/pedal position sensor in my moms Impala, and now we're getting these issues in again now, all these electronic add ons hardly give any power or efficiency, just all headaches down the road. I wish I was alive during the all mechanical era of big blocks! Also it seemed like on turns the ABS would kick on and stutter for a second while flashing the traction light for a second also- I believe it may be a wheel speed sensor in the tire assembly? Too many similar dam sensors it can be all joined in 100 feedback loops!
I've seen impalas with clearly clogged VVT Solonoids throw every code but loss of engine power, even no start conditions. Definitely a fickle creature
I guess Im asking randomly but does any of you know a trick to get back into an Instagram account..?
I was dumb forgot my password. I love any tricks you can give me
I had this problem with my 2011 Chevy Impala for over 2 years. When it would happen and I had "service stabilitrak" and "Traction control" show up, my temperary solution was to disconnect the battery for about 5 minutes which would reset the computers. This worked for the short term but only short term. Eventually the problem came back. All the videos I viewed indicated frawed wiring and a mechanics help. This video was the only one which made sense so I took a chance and the sensor replacement solved my problem and was something I could do myself without help. I performed this solution 2 months ago and it has worked. I bought the part on ebay saving about half of what retail would have cost. I would highly recommend this sight for solving small vehicle issues. Always do your research before making mechanical repairs on your own
you are great!!!!! i am a 77 y old female and i am going to tackle this on my 2012 chevy exp 2500. might have to get a couple of tools. thank you so much, so much
TIKI TIKI 😄
You go girl, not it out 77......
So tiki tiki how did it go. Success I hope
If you're near the east coast I'll gladly help ya anyway, keep on beasting it chick! 🤙👍
Thankyou so much!... I was driving my 06 Impala ss and the "service traction control" came on along with the "reduced engine power"... I got it home in limp mode after only being able to go 30mph with a very rough idle... got it in the driveway and starting looking... I noticed when I turned the key to the "on" position I could hear a very loud grinding noise... Turns out the gears inside my throttle body were stripped therefore causing the rough idle and grinding sound. Picked up a new duralast Throttle Body installed it myself in about 15 minutes started the car and acted like nothing even happened in the first place... Came here first to see that the problem mightve been and low an behold... Throttle Body it was... lmao
Very informative thanks...I've had this problem...I fixed the throttlebody...the problem came back intermittently, on my 2009 buick lucerne 2009 4.6l cxs, it drove me crazy, this problem can come from a bunch of different problems, including bad ecm, all the way to a bad short or ground, thank God my problem was from a low battery, make sure everyone has as full charged battery, because if the ecm/computer dont have the correct voltage at the time its started it will act the same way...your battery may seem hot as mine was, It even had enough juice to spin the engine with out hesitation, it will fool you, until I checked the voltage before starting and it was at 12.1 volts....if this happens , clear codes, reset the ecm/computer (Google process). Then replace or charge battery as needed (in that order) Before starting again. Hope's this helps anyone who's having similar problems.
Thanks for the info
Awesome, I have a 2008 Impala with a 175k, got this code as a pending in the history.
Erased the code, never came back, no issues as of yet.
Came here for the relearn stayed for how well shot this vid is. You focused on the important points visually without bad angles or obstructions (usually poor vids I've seen had parts of the hand or angles that didn't show exactly what was taking place).
Great learning vid and agains...shot so well.
RPO means "regular production order" and is asking if it is rpo uh8 . That info is on the production code sticker in your glove box or trunk.. Also has paint code info on it
Great vid. HOW TO CLEAR REDUCED ENGINE POWER. Tps reset on lots of gm is key on but don't crank the engine in this order. Key on, key off, key on for 5 seconds, key off for 5 seconds, key on for 15 seconds, key off for 15 seconds, key on, key off, start the truck. This will clear reduced engine power and will probably get you to a shop.
or pull maf wiring harness plug, blow on connector, check pins to make sure they arent bent.
put wire harness end back onto maf, and start it up.
also, check your pcm ground wire on valve cover bolt,passenger side rear of engine, and check your engine ground strap opposite of the same side, rear of engine.
That worked on my malibu!!!!! Thanks!!!
Really fantastic, clear video and audio!
Hopefully this will help to future viewers...... The TPS is simply a Variable Resister! To describe it closely is as follows. Consider windshield wipers as an example. As the wipers move back and forth, they will tend to wear down, will start to bind and squeak and leave streaks on the windshield. That is exactly what happens to the TPS contacts as the throttle is constantly opened and closed over time. It just simply wears down the resister on the circuit board and or wiper contact that moves with the throttle plate. As it wears down, it will give inconsistent/intermittent signals to the OBC/ECM.
Kinda like drinking beer and smoking pot to some of you as it confuses the Brain/Computer to think one thing when something completely different is going on. Therefore, the body, or in this case, the engine will not respond as programmed!
Just a little hint to you DIY mechanics and/or junkies!
Cheers
Very well explained
Not to be a now it all but the tps is called a potentiometer. A wiper moves across a voltage resistor as the t.b plate opens and closes. Varying the Volts, not like a rheostat that varies the amps. Usually the constant wear creates dead spots in the tps signal.
Lawd Fadda.....someone trying extra hard to be technical.
Yea exactly on these eco shitty flex fuel boosts . was driving a 2013 Chevy Malibu nice looking beautyful car piece ashit. Took it for a drive , smoked one from California stopped at corner store for a big 🍺 , smoked and drank took off to HWY. Pice off shit running 40 miles at A HWY. At 75 .i. Freaked out though i was running at hi speed . am never gitting hi in a f*#!n Malibu eco flex
Thanks, great video. Had P2122 on my 2008 Impala and reduced engine power intermittently. Became a almost daily, so I replaced sensor. No luck, code came back same day. So I tried replacing accelerator pedal and voila, code gone! Knock on wood it lasts... Only been a week so far but it had been coding daily up until I switched the pedal... Hope this helps someone out there! GL
I replaced throttle body sensor. Came back on... changed accelerator sensor. Came back on... I'm so over my 2009 Malibu
Thank you bro. I almost took my truck to the shop. You are a God sent to help us peasants. Lol. Awesome video.
Thanks!
Thanks for this video! My car has reduced power on me while driving while also showing service traction control & service stabilitrak. I'm a 38 year old woman who is learning to do things on my own with my vehicles!! This sure is one I'm going to tackle again on my own yay yayy 🎉🤘
I’m having the exact problem with my Silverado did this work for you? Or what did you do to fix it?
Yjkjdejdjdj
Would it go on limp mode?
Very, Very Helpful! My brother in law is a mechanic, but I tackled it myself, THANKS TO YOU!
Awesome! Good job!
Thank you sir. I was just driving to work and about 4 minutes down the road this happened to me , luckily I was able to make it to work, and when I got there i turned my car off for ten minutes and turned it back on it was running alright, so hopefully it lasts me till I can get a new part.
Clear and concise instruction. Idle patter helped a little bit, too. However, only good if it's the throttle body and not the accelerator pedal that's the problem. Would the scanned codes differentiate the possible problem sources?
This problem can be caused by a variety of things. For me it was the hi pressure fuel pump. Replaced that & it fixed all my problems. I've heard it can be a dirty throttle body. My point is that there is no one fix fits all solution. Good luck!
I had a 2008 Malibu a few months back; same problem but the "Reduced Engine Power" and sputtering came after 6-8 miles of driving and would go away if you just let it stand for 6 to 8 hours (overnight). I replaced the both of the Variable Timing Solenoids, and another variable timing sensor; Didn't fix the problem. Then after watching a million RUclips fix it videos (because I am not a professional mechanic), I replaced new Battery Terminals, removed and ran without the Thermostat (even though there was no heating problem), and even tested with a direct connection to the Radiator Fan, so the fan will run constantly (again there was no heating problem but a RUclips video suggested that it fixed the problem in their same model Malibu. It Increased the 6 to 8 miles to about 10 miles, but the never can get rid of the Sputtering and the Low Engine Power that will just happen.
From all the videos I watched and the comments I have read, this problem can happen in the Malibus for so many reasons. There is NO one fix. Even the Chevy dealership acted like it was JUST MY CAR, when so many people were having the same problem and the fixes weer so different. The dealer wanted $200 plus to diagnose. Some people had issue reoccur after spending Thousands at the Dealership throwing new parts. Just do the research by reading the comments on RUclips videos.
Then there were some people who had fixed it by replacing the main fuse box. For some people, it was the traction control that was causing it.
I would have let you have it for free if you lived close to Los Angeles. I just junked it and lost about $3500 and a lot of time and effort educating myself, working on it myself etc etc. OMG The aggravation is just not worth it.
Just Don't buy a Chevy Malibu or an Impala. Even Hondas and Toyotas have this VVTI but not these kind of issues after 6-8 miles of normal driving. Then you have to drive home at 10 mph and it does not go away even if you start it in 2 hours -- needs to be left alone overnight. It is FUNNY.
Chevy made these cars with a lot of sensors and from what I understand even Chevy does NOT know what's wrong when the issue happens because all kinds of problems can display the "Reduced Engine Power" warning and the associated sputtering, like it is running on 2 pistons.
I am Just gonna start RUNNING if anyone even gives me one of these cars for free. I have never had a car like that 2008 Malibu.
I have a 2011 Chevy Cruze. Same problem with engine power reduced. Just got my throttle body ($158) later. Getting ready to go put it in with my brother. Will let you know how it went. WISH US LUCK!!
Did it fix the issue?
Hell no, I replaced both throttle body and gas pedal
Junk it
@@geotid8275 doesn't fix shit it'll keep coming back no matter what you do, SELL it
Change the MAP sensor. It's only like $16 usd
It's the best video around here where a person can actually see the job and can say '' I can do that'' This video should help people with a Chevy Traverse, since they seem to have this problem. I own a Suburban , never had this problem But I love this video and will be a helping hand from me to someone someday :) t.y. nice job
Thank you!
TPS sensor also on another video a man diagnosed it and saw where 4 electrodes are fused together
carquestions
ruclips.net/video/C5BEPmFB6cw/видео.html
Those clips are easy to install if done correctly. Hammer not needed. You did install of clips backwards. "L" shape goes on first. Then press the "V" end on. No hammer needed. Beat on those parts can cause damage.
Enjoyed watching this. This issue just happened to my tahoe. Gonna do this fix and see what happens. Thanks so much for the information.
Thanks! I hope you got yours all figured out.
I love the clear and concise descriptions and instructions. The camera and lighting positions really made a difference.
My battery was near dead, used a halo jumper, got it going, got to the bottom of my street to find reduced engine power. I had to put the hazards on after pulling onto the main road just to limp off the main road. I let it run for 20 minutes, shut it down for over 30 seconds to reset. My first attempt didn't work, because I didn't wait. Most electronics in cars, I've found have a 30 second reset time.
I have this issue, will try the sensor. I replaced my accelerator pedal thinking that was the issue and it did actually help something, it’s driving better, but I still get this code, the traction control code went off though! Ordered the part so hopefully this fixes it!
UPDATE: totally fixed the issue in my 2008 Chevy impala! Thank you! And an update for anyone they’re discontinuing that part! I got one of the last ones
@@toomanystrawberries I look in my local junkyard for these gem parts. Super cheap there.
What part did you order
Thanks so much for the video. It was only slightly different for my impala ss. Instead of cleaning the throttle body, I just ordered a new one as well as a new gasket. I put it in this morning. Plug and play and so easy thanks to your walk thru video. Saved SOOOOO much money. Thanks again!
That's great! Thanks for watching! Btw...I have an Impala SS sitting out back if you're interested in a parts car lol. Bad trans...
My 2015 Buick Verano just started doing this. It will come and go and hate when it does it on the freeway. Hope I can get it fixed.
That happened to my car it had several problems so I had to replace several pieces at once total cost was like 220 or 270 maybe less but this problem in specific I just fixed it with 8 dollars just got a kit to clean the Throddle body got it in and immediately the car was running better other thing I changed was the thermostat coolant system and this was the most underrated and most simple fix that caused the most trouble just a dirty hose clean the end of your hoses people they get clogged and you get shitty airflow etc this where the problems / really rough idling / car rpm when yup and down all the time specially when stoped and sometimes the car would just stop working and I had trouble while cranking it it would take several tries and like 4 secs/ poor acceleration / ac off due to engine high temp this was just a cable / idk what else I changed other stuff too for example when I pumped gas the car had trouble starting or in general it had trouble the fix was a purge valve idk over all I fixed everything mi car was messed up from the previous owner it took me like 4 5 hours I’m no mechanic but I learned there is some maintenance you need to do if you want to save money and have lots of fun driving o I forgot to say the car I drive is a Chevy Cruze 2014 lt if you have any questions about the car I might be able to help you I had to replace a lot of stuff in this one
Thank you for this video my 2010 Chevy Malibu lis doing that right now reduced power and esc off lights on my dashboard
Great job, I have been having to deal with this issue with my 2011 Chevy Camaro SS. I took it to the Chevy dealer and the tech scanned it and told me that I needed my throttle body cleaned but he said that they would tell me to just buy a brand new one so that they could make a dollar off of me so he reset the error code for me. It happened again about three weeks later I let the car sit for a day and came back and started and it went away along with the check engine light. I have to get it done soon so thanks for the very informative video.
EdifiedSoul I’m having the Same problem, I have 2011 V6 Camaro and I don’t know whether I need to change the whole throttle body or to change the electrical part only , tell me what happened with you please
Junk it....get a ford....problem fix
Mine came on while driving. I googled possible causes and one answer was to not use E85 gas. I currently had E85 in my car, about 1/3 tank. I filled up with regular unleaded and the issue stored within 2 days and my car is running fine now.
Very excellent ,
However , you can
clean it in position
without removing it
( the throttle body ) .
Also , you can use
brake parts cleaner
for cleaning the throttle
body without any problems .
I used brake parts cleaner
so many times in the past .
Great and helpful video. If you put a towel under it when removing nuts the towel will catch the nuts you drop.
RPO (regular production option) codes are on a sticker in the glove box or in the trunk where the spare tire goes
Thanks for that info!
Berryman B-12 CHEMTOOL Throttle Body Cleaner is the Bomb ! Great job , cables are better ...
my pontiac just flashed reduced power engine and I think I can fix it by myself!!
Madeline Lewis RUclips has that affect on people lol
How did u fix it? I have the same car.
rpo and uh8 refers to build options. you can find out in the glove box. has a list . you have to designate correctly or it can effect your diagnosis
Thanks for that info!
I have a cadillac fixing now but mine has only 3.2 reference volts at tps so as well as cleaning I get to go through a mile of wire!!! Lol...yeeehaaw
Check wiring harness on front of engine.
13:23, did anyone notice he forgot to put the air filter back in?--, besides that I'm going to try this to mine in the morning. 👍
I went go buy a new FRAM air filter when I did mine...it does NOT fit exactly right...makes it such a pain trying to get it all back in!🤣😂
08:39 I think they mean the plastic sensor part, those cleaners eat through plastic - excellent video though, brilliant!
RPO is "Regular Production Option" -- or in other words, what you car was equipped with when it was built. UH8 is the cluster for coolant temp, tach, and trip odometer.
So it's just asking if you have a tachometer and temp gauge in your car or not.
That’s good useful information, thank you!
I had the reduced power on my 2006 lascrose changed the throttle body and still no change. tried to reprogram the throttle body using a relearn procedure still no luck. I finally took it to the dealer and the fault codes indicated the the gas pedal sensor was bad. They changed the gas pedal and my problem was solved.
What code did you have? I am getting P0221, did you have that one?
Check your air intake might have a crack same problem with the cruise found out there's a big crack the intake attaches down to by the engine
RPO code is in the glove box you need to look if you program a computer hope this helps
Thanks!
I had this problem with my buick 2013 and the mechanic collected almost $3000 to fix it for me !
my 06 buick rainier had this exact problem and we are going to apply this fix now...fingers crossed....tired of stabilitrack messing with acceleration flashing...waiting to accelerate after the dumb thing quits flashing..which btw has gotten worse over time...will let u know how this hill billy girl does!
Good luck and post the update!
Rpo is a list of options on car usually in trunk also has paint code on it it was asking if it had that option
Thanks for the info!
Great video man, I’m having trouble with a 2010 terrain and this video was very useful,so much that helped me cleaning a throttle body from a Chrysler Pacifica, it’s a different type tho, not electric. It was sticking and the cleaning solved the problem. Thanks for uploading
Good video, im having that issue on my 2011 impala. Will try this before taking to the shop
Hopefully you're able to fix it yourself and save a few bucks!
I've got an ecotec giving me a fit. Cleaned the throttle body and its still running like crap. "engine power reduced" "service stabilitrac"
Got me singing the old Merle Haggard song, "I wish a buck was still silver It ... Wish a Ford and a Chevy Could still last ten years, like they should"
I put a quart of Lucas high mileage oil additive and presto no more p06de code it would come on in about 2miles continuously cross your fingers oh by the way it said low power but I couldn't tell that it had diminished power .I also put a c shaft position sensor on and it helped the running ability some but be careful that bolt will easily break off into the block I would recommend using the original bolt on the sensor . New throttle body did not help . Couldn't get to that oil pressure sensor yet . I intend on shorting a deep well socket to get to it more easily and a flexible half inch drive I believe this will work on 2.5 Chevy Colorado 2016 you have to get that white clip completely off and you can then push off connector with a long screwdriver
You have no IDEA HOW MUCH THIS HELPED!!!!!!!!!!!!!! THANK YOU!!!!!
RPO codes are factory info of the systems/parts on the vehical. They are either in the glove box or on top of the spare tire cover .
My job has several vehicles in its "fleet". One of them is doing this same issue. One of our guys says its the traction control module. I'm gonna do this fix first. All it will cost is my time and the cost of the kit. Less expensive then towing it to a shop and paying them to do the work. Let you know if it works.
If you want to ;
clean electric electronic
throttle body in position !!! ,
all you need , just put ignition
switch ON and keep it ON until
you finish the cleaning, it will
open the throttle plate for
you to clean it .
lol the svc tire monitor, mine has been on a long time. pontiac g6. I have traction control problems for a while now. Can't figure it out. Examined the throttle body sensor, ecm, tcm, map, wheel sensors, examined the hoses... going to test the ignition coils. it's coming to wires at this point .. no idea where.
Regular Production Options(RPO)-Codes
UH8 - cluster-cool temp,tach, trip odom
I juuust watched ur video I have that very problem right NOW on my Cadillac DTS...
Thank U...!!!
👍👍
Did it fix the issue
Wondering if you ran into this problem on a 09 escalade this stabilitrak thing is stressing me out and mechanics haven really given me an answer to the problem thanks
You are awesome thanks so much for taking the time to make the video i haven't tried it yet but regardless of will this solve my issue, i do want to thank u for being concise and taking ur time to teach...thanks so much...
Thanks!
I have a 2010 equinox that is doing the same thing. I replaced the throttle body which came with a new tps. the thing is , it's still doing the same thing...I've tried doing the manual relearn several times where you start it up and let it idle for three minutes then shut it off for one minute x3...I even left the battery disconnected overnight...still no luck
Man thanks. I replaced my pedal sensor. And 6 months later bam it's doing it again. I'm gonna buy a new throttle body
Change the MAP sensor first. It's only like 12-20 bucks online. Then if your problem continues then change the whole throttle
@@torerotigreen9198 Yelp it's the throttle body / and sensor. Mines was dirty and I had a crack in my hose at top. I replaced throttle body and hose runs like new
Terrance Patrick Dave your money!! Put new plugs and a gallon of laquar thinner in gas tank with ten gallons of gas,, it cleans everything!!!
Have the same for my chevTahoe 2017, gonna go to dealer this week, I’ll keep you updated
Mohammed Alamri what did they say?
RPO UH8 is Regular Production Order package UH8 insturment cluster coolant temp, tach, trip odometer.
Great job buddy............ thx much for teaching us!!!! 👍 👌 👋👋👋👋👋
I got the same prob. with my car. 🙄🤪
It'll come back on, the issue is the hub assembly connection. Fix that It'll go away. Even though that code came up for that throttle body actuator
U saved me 600$ thank you 😊
Excellent video for my 2010 Piontiac G6,
thank you for your contribuition for all the people that have the same issue but to be honest each case is different is no t always the same, let me tell you my experience, l had issue with my differential and i spend a lot of money with 3 difents mechanic that just want to steal my money because one said that was the cv joint other that diffential but, at this time i dont know exactly what was the problem, the point here is that finaly i fixed the diferential problem but the engine power is reduce light sudenly came out and the mechanic thief said that was the throle body, but finaly i found a honest mechanic and was something about the gas sensor, to end this tip to my experience not always is the throttle body think more the two time to move at your throttle body because is really delicated
Thank You so much for doing this video, it has alleviated a huge headache 🙌🏾😁
Hello brother i have a malibu 2013
Today i got the same problem .. the car was fine till this ( check engine with downword arrow + traction cintrl lights went on )
The code on dashboard is code 84
And when i checked it on computer the engineer told me its from the fuel pump i bought a new one but still not solved i hope ur video helps me tomorrow .
Appreciate ur help
Thanks for watching and good luck! Let me know what the fix was, I’m curious.
Did you ever figure out was it was I been having the same exact problem with my 2013 Malibu Ltz they told me that I had to change my front fuel pump. So I paid Chevy to change the front fuel pump after doing so I picked up the car and it ran fine but after 20 min of running the car would just shut off there is no check engine light on what so ever took it back to Chevy now they are telling me its the Exhaust cam sensor that’s causing the car to shut of wile on red lights I don’t know what to do.... fuck Chevy I will never buy a Chevy ever again
i am wondering...
if the computer was silent,
and all the sensors were not triggering,,,
would the vehicle have gone into reduced power mode,
or would it have just operated normally...
That was a very good video. Although I do not have that problem, it may become helpful because my son owns a Chevy Malibu. Would it be the same? Also, I did notice that traction control light but you did not mention anything about it since this video was not meant to fix that, however, my son's 2013 Malibu has that same light that will come on when he brakes. Any diagnosis/fixes for this problem?
It worked on my Malibu 2008 thanks allots
That’s great! Thanks for watching!
What worked for your malibu cleaning or the sensor
I was told that also the air pump will come into effect, since it brings clean air for combustion, I might replace the air pump since it has a lot of miles already
Update on this... Also you can change the MAP sensor. I'm goes bad due to the heat exposure. Try this first is only around 12-20dls it won't hurt to have it replaced.
Good Video Sir👍
Prime it 30 Dec nds two times then third time try it should be be good!
I have a chevy equinox 2010 with reduced power engine and traction control. when scanned, code P0089 and P228D is erasable. Is this method also useful. I bought new high pressure fuel pump, not still working. what do I do?
I own 2011 Malibu, purchased in OK now live in Nebraska. I just spent $500 for this issue to be “fixed”. Drove 500 miles home to OK for Thanksgiving holiday. Car ran fine. On my way back to NE about 150 miles from home as soon as the much cooler & moist air hit the same issue! This car belongs in the river! I will NEVER buy a Chevy again!
It’s possible there’s a break in one of the wires near the throttle body connector. That is also way too common on the GM’s.
ts6034 thanks for the tip. As soon as I have a competent male stop by I will have that checked out. I am just not sure how much more of this car I can take! I bought it in June of this year with only 115k miles on it. It has broken down on me 8 times. Chevy has made it impossible for single women to own their brand. Have you ever dealt with the wiring issue that I keep reading about?
@@kristimorgan9012 The wiring issue on the throttle body harness? Yes!
I have a Cruze and I agree. Chevrolet is garbage. My friend has Cruze and he has problems. I had 2 coworkers who bought a Malibu and both had transmission issues.
kd k AHG!!! Don’t say that! So far the transmission has been good! I swear I will drive this bitch into the river if another thing goes wrong. I’m all about getting what you pay for & Chevy’s aren’t cheap! I’m ALWAYS looking at the newest cars coming out & as far as looks Chevy draws me back in every time. Last fall I was looking at 2019 Tahoe & with trim package I wanted sticker price was close to $74,000. C’mon I would have to save for what seems to be the rest of my life. Chevy has brought back the blazer for 2019 & I do love the price. As for our Chevy’s that are already out there on the road, I suggest finding a certified Chevy mechanic avoiding the dealership...I found my certified GM mechanic at Graham Tire in Grand Island, NE. By the grace of God, an auto parts store employee steered me in his direction. My Bu is running fine now, fingers crossed & knocking on wood. Best of luck to you you, with your Cruz & your friends with the MaliBu’s!
You just saved me!!!! 2013 buick verano.....
That’s what I have.. lol and I’m having the same problem, and I’m also 9 hours from my house 🤦🏾♀️
Did you just use the same rag with the throttle body cleaner to clean the O ring which you took off 😳......but good video just clean mines keep it going
Really enjoyed this video. I replaced the Throttle body with a new one, the car started fine tried to drive it and it started throwing random codes. I can clear them with my reader the car will run fine but they return after sitting. I disconnected the battery cables jumped them together for 10 minutes reconnected them and noticed the radio presets didn't clear, did this sequence 3 times withe the same result. Codes returned each time. Is there something else I should be doing? Thank you for the information.
Thank God I have an 03 that has cables it has 160,000 miles on it and it runs like new
UH8 CLUSTER-COOL TEMP, TACH, TRIP ODOM
UH9 CLUSTER,INSTRUMENT(TEMPERATURE,TRIP ODOM,TACH OR INFO CTR
Hi there thanks for your video, question the butterfly has to be closed all the way down or can have an small gap?
It’s normal to have a small gap. Since drive by wire took over, throttle bodies don’t have idle air control motors so the throttle plate does that job. Hence why you’ll see a small gap.
map sensor problem shvrolet Malibu thank you
Got this same issue with my GMC Acadia 2007, its totally random. It mostly happens when I start my vehicle on cold morning and let it pre-heat. If I just get in and get going with cold engine it usually does not happen.
Hi. Thank you for the great video. I replaced the whole engine throttle body on my son's 2009 impala with an OEM Delco part. It went well, thanks to you! Unfortunately, he is still getting the same engine power reduced notice....any suggestions? Thank you again.
I have a 2003 GMC Yukon Denali has reduced engine power light on the dashboard I replaced the gas pedal sensor throttle body module and the throttle body it's still on what do you recommend? I wonder if my throttle body is a bad part
Have it scanned and find out what codes it has. They’ll point you in the right direction.
I scanned it with my Fixd device and it shows the code p1515
I keep getting the engine reducing power code also. But when I read the code it says throttle position sensor. Circuit E low voltage.
So you could have looked at the data on your launch and looked at TPS data. Next, hook up a three wire variable resistor in series and rotate the resistor. Should see the tps value move on the scan data. This verifies the wire integrity before you just go and buy a sensor and slap it in... guessing works sometimes, but its good to verify the fix before you replace parts
I took my car to Firestone for this issue and they did 1500 worth of work just to get it back and have the same issue. They said I should go to the dealership. And all I could think is why didn’t you give me this information when you did the diagnosis so I’m out $1500 and I still have the same issue
Great video man.really appreciate your straight to the point format. should I unplug my negative unit on my battery before i pull my throttle body off ?
Yes. It’s good practice to always unhook the battery when performing repair.
Yesterday I received the same warning. Could still rev and drive. Today there’s no warning message or lights. Does that mean mine is starting to get to this point?
This just happened to me and I waited a bit to turn it back on and I could drive back home luckily.
this is a nice coaching watches and learn, thank you.
2013 cruz 1.8
I've changed intake crankshaft, both camshaft sensors, MAF sensor, cleaned throttle body.
Now the stability control service is on.
How can I find the issue that may or may not be like you're video?
Please help tired of buying things I don't need.
U A BEAST!!!!!!!!!!!!!!!! HAD MONEY 4 GEICO WHEN I FINISHED
That sounds good! Sounds like my motorcycle. HAH!
You did a great job