How To Install A Battery Disconnect Switch
HTML-код
- Опубликовано: 1 окт 2024
- In this video I show you how to install a battery disconnect switch. Isolator switch install. This can be used on a car or a truck or a camper trailer etc.. This is a summit racing disconnect switch.
This is the crimper tool that i used in the video:
www.amazon.com...
check out my channel for more videos:
How to change a tire pressure sensor (TPMS) yourself:
www.youtube.co....
Dakota digital dash Install (1982-1992 Camaro)
• Dakota Digital Dash In...
How to install a 4L60E transmission:
• How To Convert a Stick...
How to Wire A Switched fuse block:
• How To Wire A SWITCHED...
Complete Brake Overhaul:
www.youtube.co....
Vintage air serpentine setup:
www.youtube.co....
How to Upgrade your fuel pump:
www.youtube.co....
How to install an electric vacuum pump:
www.youtube.co....
How to build a camaro from top to bottom:
www.youtube.co....
400 Cubic inch small block Dyno testing:
www.youtube.co....
How to Clock an Alternator:
www.youtube.co....
How to Replace a u-joint:
www.youtube.co....
How To install a trans pan drain bolt:
www.youtube.co....
How to install subframe connectors:
www.youtube.co....
How to do a quick wheel alignment (toe in toe out):
www.youtube.co....
klowny1969 - best car mechanic on youtube
Only clown mechanic in the world ! Uses for an air hammer
This video can be applied to chevy, ford, mustang , impala , camaro , corvette, truck , toyota, lexus , honda , nissan. etc.. volvo cadillac gmc astrovan truck blazer silverado turbocoupe thunderbird clown clowny69 klowny69 GMC Savana 2500 Siera 1500 Sonoma isuzu hombre GMC desoto mopar vice grip klown garage restoration old school relics will it run barn find hasn't started in 45 years 1930 1940 1950 1960 1970 1980 barnfind
My battery is in front. 05 yukon. I need the switch inside. I was told not to run big guage wire that far. They suggested a relay at battery negative side and use small wires to inside to a smaller type switch.
I fail to see the reason why.
Disconnecting the negative side should have no effect on the amperage going to the starter. I'm really confused about the opinions on this subject.
And the comments from the Marine business said tap into the positive side.
Unbelievable confusion
You know that the starter gets it's ground from the engine? So your only talking about the positive side. It's not recommended to use a big cable going inside the car because if the positive cable shorts out..that will be a definite fire...don't forget to subscribe 😉
Installing that battery switch much easier than finding that short! Thanks Klowny!
LOL yes it is!!
Suppose that just goes on the negative side?
Is there any risk to a longer run? IE switching the negative side of the bat between the terminal and grounds with a 4 to 5ft run through the firewall to mount a high amp switch like this under the dash. '73 F250 Highboy
I didn’t watch video, cables burned up incorrectly connected negative cable
Sorry to hear that..don't forget to subscribe and hit that bell 🔔
Awesome!!!!, I need one on my camper van but I don't know the wire gauge that my battery is using. Is there anyway around that? Where are you located? Who installs these switches?
Alrighty! Loving me some quality Klowny time this morning! Installation done to perfection. Really liked the shrink tubing and loom you put on the cables. I use the same switch on my pro-street 67 Mustang. I also have a separate kill switch under the hood for the fuel pump. Thanks for sharing and cheers from Motown.
Thanks for taking the time to comment and watch my video. Thanks for the compliments..love the pro street look..keep tearing the streets up :)
Awesome. I want one of these on my 79 camaro. They're useful and are just cool looking on the car lol. Thanx Klowny!!!
Yes they are..love the 79's!!
Best installation video content ever. Oh yeah baby 😂!
Thanks man!!
Thank you for the informative video, one will be going in on my 74 Bronco soon.
Awesome! Thanks for watching and don't forget to subscribe
Thank you, very informative!!❤
Thanks for watching and commenting ..don't forget to subscribe 😉
Gotta lube it with that butter sauce before you drill it! Awesome job man. Nice clean install!
Lol thanks man!!
Hey Klowny how you doing? Great video.
Thanks man..doing good..it's been a cold winter..urself?
@@klowny1969 All good over here in the UK. Roll on the summer.
Glad to see you dude,where you been Klowny
Thanks man..it's been a long winter lol I will get back into filming again in these coming weeks.
Your a wicked dude K69
Nice job, very neat!
Thank you!!
Why didn't you put some solder in that zero gauge wire connection
not necessary..you can put some vaseline or silicone lube if you want..don't forget to subscribe
American Chopper quality 🤡😄
Yeah baby
Why there is no one knows reasons for killing battery?let me tell you,reason is simple,there is water submerged the wires,especially the connection points,caused linkage of electrons.
Uhmm there could be a draw
That bracket took that big hole cutter like a champ baby!
She was a trooper!! Came back looking for more!!