I've put together a Q&A session for most of your questions (e.g. how to remove the barrel and cylinder, changing the grips) in the new video. If you want to know more about this revolver, watch this: ruclips.net/video/o06woiSyUp8/видео.html
I have the newer umarex smoke wagon. Internal structure is very similar to yours. This video helped me a lot in finding the issue with mine. The issue turned out to be the hammer spring snapping. Thanks a bunch for making this video.
@@arussianspy3114 I called umarex and I paid them to repair it. They replaced the spring themselves and shipped the gun back. It was about $60.00 usd to have it repaired and shipped.
hello again, i had to replace the hammer, becouse the stud which the holds the chamber arm had broken off the hammer, but the repair was sucessful ,thanks to you and you and your vidio, thanks again graham in England.
Having a lot of difficulty putting the last spring back in for reassembly, the one that's supposed to be leaning on the sear of the rotating chamber. It keeps springing out or moving the sear the moment I let go and have to be inhumanely fast and accurate to put in the side before either of that happens
I have two questions: Are the insides of the peacemaker the same for both the Airsoft version, and the pellet version? Question 2: To your knowledge, why didn't they make this gun easier to remove the cylinder to clean the barrel?
High Noon45 1. Yes, should be the same. Because the disassembly is the same. Not sure whether they are 100% compatible though. 2. The design of this SAA follows the older version of the real steel SAA. So the cylinder is not detachable like the Tanaka SAA
On the Remington 1875 by Crosman you can strip out the cylinder easily in seconds, using the way the actual real colt can be stripped, so why not the umarexes.
Can you do another video but disassembling the entire gun. I recently purchased a different length barrel and different color wheel cylinder and I would like to install them.
Hey, I have a question for you do you know where to get one of the hammer springs, mine broke and I haven't been able to find a place to get a new one.
The piece the hand rotates on snaps on both the ones I've owned have you had this problem also? I fixed mine with Krazy glue and needs to be reapplied every once in awhile but still works
I inherited a 1959 crossman single action 6 in box with manual. It's in perfect shape except my grandfather took it apart to change the seals I guess. Could you replace the seals and put it together for me? I know they aren't worth much it was my grandfathers. Please tell me what you think. Thanks Neal Apollo Beach Florida
Got two from red wolf airsoft dot com, most everyone else is sold out, mine actually came in the mail today and im on the video to make sure i put everything back in proper order 😂
Hi, I am interested in the color of your Colt, did it come that way or did you customize it? If you did that your self did you video the process? I would love to do that to mine, is it a type of case hardening? What ever it is it is SICK!
Thanks, this is the blued version of the revolver. The finish is already there out of the box, not self-made. However some of the blue colour will be lost after a while, especially when you’re frequently handling the gun with bare hands. And start showing the bronze underneath.
Hey I have an issue, my hammer is a bit wobbly when it’s in the resting position. The gun works fine tho. the hammer just goes back and forth a little while all the way forward. Please answer!
Great video! Does the second grip come off in case one obtains spare umarex grips, or perhaps wishes to engrave or customize the grips that come with the gun? Thanks.
Addison Schraeder Most of the time it’s caused by over tightening the CO2 cartridge and damage the rubber seal of the chamber. If your gun is leaking CO2, better check the condition of rubber seal. Of course it’s the best to seek help from an airsoft technician.
from my experience, the finish is shit though. it got really ugly for me for literally no reason, most the bluing came off the cylinder and grip for me
Branleur Et Fanning means holding down the trigger and pull the hammer down repeatedly. Because of the revolver is single action. When the trigger is held down and you pull the hammer down repeatedly, the gun will keep shooting like a full auto gun.
I got mine yesterday and the cartridge ejector didn't work , thanks to your vid i managed to dissassemble and re assemble the gun. And i fixed the ejector! Works like dream now
It’s a piece of metal. You can take off the grip and try to use a small screwdriver to get it out. But I don’t recommend this since this will leave a hole on the grip.
Thanks. I'm going to try this. My spring is messed up and it has zero tension. Do you thing I just need to replace it? I will admit that I fanned the gun. Cheers
@@ryderpoulin4875 If you have trouble finding one then go to co2-handguns.freeforums.net/ there's a guy that sells them in the sales section and posts worldwide.
marshal madsen You should be able to spot the two small phillips screws that are securing the right-hand side grip once you popped out the left hand-side grip. Losen those screws and you’re good to go.
My experience with all of these Co2 guns is that they work for about 3 or 4 cylinders before they malfunction, exit all the air and are broke - and they are hard as heck to replace the seal gaskets in them which run about $20 - so I just throw it on the pile with rest of them as they are just junk.
Manos Zervos There’re several generations of the Colt SAA. The removable cylinder version is a more modern version. You only get this version of replica from Tanaka. The Umarex SAA is replicating the older version of the SAA.
I fully disassembled my King Arms version and it's completely different than this one so it's not like I can follow these steps in reverse like I thought I would lol
at the point you removed the side plate, you failed to point out, the fact that the chamber rotating spring was off the lever arm, ? the reason the chamber was not rotating..but thank you anyway, i have that exact problem with my saa, now i know what must be done.
@@SemperReloading that could work! do you also maybe know any other airsoft/BB/pellet single actions that don’t have the screwed up hammer? I’m very picky I know but just curious
You can fix it by taking a ziptie and some rubber bands zip tie the rubber bands too the back of the trigger works like a charm you can trouble shoot the best place to put it I put the zip tie threw the center of 3 small rubber bands than I move it undee the trigger works like a charm!
I dont know why but after disassembling, my safety doesnt work. It just got loosen and lock/ unlock by itself. Can u help me? As i know . there wasnt specific spring or pins when i removed the safety . there was only safety part to remove and put back in
@@SemperReloading after i read ur reply, i searched all over and i found one square- ring in the shell-frame that i disassembled from main part, and i have no idea how it was stuck in there,anyways ive found it and fixed it well thanks to you, ty for replyin even tho it's the video that has been some time.
@@ArgosWarrior The lower one is inside the frame, you have to remove the side plate to get to it. I'll give you a link to a full step by step guide that one of my friends did for our forum co2-handguns.freeforums.net/thread/893/colt-saa-loose-barrel-repair?page=1 Go and have a read of that buddy, that'll tell you everything that you need to know.
@@SemperReloading no I mean it does not fire the bb as it gets stuck between the chamber and barrel its not the c02 has its new but even when in safety mode the chamber is still sloppy .is it a spring issue or something more sinister. the hammer goes down three clicks before firing as it should but on half cock the cylinder spins very freely and I am seeing c02 coming out between chamber and hammer on firing it worked spot on the last time I used it it also fired the first two bbs perfect before problem arose many thanks ROD
The Lone Ranger It’s supposed to be there. There’s a spring attached to the hammer to create this gap, so that the gun won’t shoot all the CO2 out in one single shot.
@@SemperReloading thanks for the reply and like. Yes I know the gap on the Umarex is suppose to be there for the reason's that you said, but the real Colt SAA doesn't have the gap. Now some owners of the Umarex have modified it greatly reducing the gap and not had the problem of touching the pin value therefore not venting Co2 off, it just make the appearance look 100% better. Why I think you should have a go at doing the modification is because your RUclips videos are really well done on the camera work and your commentary too is very clear and precise. I'm very sure that if you did the video on reducing the gap to the quality as the original video then once word gets out about the video then your RUclips views will sky rocket and possible subscriptions also. Something to consider my friend 🤔🙂
I've put together a Q&A session for most of your questions (e.g. how to remove the barrel and cylinder, changing the grips) in the new video. If you want to know more about this revolver, watch this:
ruclips.net/video/o06woiSyUp8/видео.html
its possible to mod the valve or anything else in order to RAISE the FPS ?
I have the newer umarex smoke wagon. Internal structure is very similar to yours. This video helped me a lot in finding the issue with mine. The issue turned out to be the hammer spring snapping. Thanks a bunch for making this video.
Where did you buy your replacement? I have the same issue with mine but everywhere I look is out of stock.
Edit: the names are ironic aren’t they…
@@arussianspy3114
I called umarex and I paid them to repair it. They replaced the spring themselves and shipped the gun back. It was about $60.00 usd to have it repaired and shipped.
@@notarussianspy508 you could have bought a new one for not much more dude 😂
mine just snapped too, do you know where i could get one?
Yeah I learned this lesson the hard way, but thanks to this video I was able to fix it by putting a new spring in!
where did you get a new spring?
@@totkampf8427 I searched online and found it on a UK website, I believe. I don't remember the site name, sorry
One should be able to modify the spring or have one made longer and stronger if need be to support fanning.
hello again, i had to replace the hammer, becouse the stud which the holds the chamber arm had broken off the hammer, but the repair was sucessful ,thanks to you and you and your vidio, thanks again graham in England.
This needs to be an introduction video to all newbie Umarex Peacemaker users.
Don't fan (it's late for me 😐)
Thanks! Helped me fix my wobbly barrel.
Having a lot of difficulty putting the last spring back in for reassembly, the one that's supposed to be leaning on the sear of the rotating chamber. It keeps springing out or moving the sear the moment I let go and have to be inhumanely fast and accurate to put in the side before either of that happens
How can u fix the hammer gap?
Try filing down the tail of the trigger sear.
@@SemperReloading yea that’s wat I thought.. thanks
Any ideas on how to fix a loose barrel? It wiggles if you move the gun either left or right.
I glued mine it fixed it
I put some teflon tape on both sides between the barrel and the frame to shim it, it doesn't wobble anymore
I had this problem and got the gun replaced now the replacement is starting to move very slightly but it'll probably get worse as time goes on
I have two questions: Are the insides of the peacemaker the same for both the Airsoft version, and the pellet version?
Question 2: To your knowledge, why didn't they make this gun easier to remove the cylinder to clean the barrel?
High Noon45
1. Yes, should be the same. Because the disassembly is the same. Not sure whether they are 100% compatible though.
2. The design of this SAA follows the older version of the real steel SAA. So the cylinder is not detachable like the Tanaka SAA
High Noon45 I'm a cowboy in Texas I own a real colt 45 SAA and this is accurate to the real thing
On the Remington 1875 by Crosman you can strip out the cylinder easily in seconds, using the way the actual real colt can be stripped, so why not the umarexes.
Can you do another video but disassembling the entire gun. I recently purchased a different length barrel and different color wheel cylinder and I would like to install them.
Maybe we’ll do a Q&A video about all the questions we received👌🏻
Hey,do you know what metal is that ?And maybe how strong that is ?Thanks.
giedrius laimikis Not sure, looks like some sort of zinc alloy. Definitely not steel.
Excellence Sir question the grips is there replacement grips example : If one ordered real Colt grips do you think they would fit ?
Real Colt SAA grips will not fit since the size and angle are completely different.
Hey, I have a question for you do you know where to get one of the hammer springs, mine broke and I haven't been able to find a place to get a new one.
Depends on where you live. But it’s out of stock in a lot of places.
Thats what I noticed, I live in the sates, hopefully they restock. Great video though.
@@zebzap9904 mine just gave out today you ever find one?
How did you get that bluing effect on the metal?
The piece the hand rotates on snaps on both the ones I've owned have you had this problem also? I fixed mine with Krazy glue and needs to be reapplied every once in awhile but still works
i have a nickel 7.5 would i be able to change over the barrel to a 5.5 or would i just be risking some serious shit?
I inherited a 1959 crossman single action 6 in box with manual. It's in perfect shape except my grandfather took it apart to change the seals I guess. Could you replace the seals and put it together for me? I know they aren't worth much it was my grandfathers. Please tell me what you think. Thanks Neal Apollo Beach Florida
I live at the opposite side of the the continent, plus an ocean. You may want to find a local airsoft/air gun store to help you out my man.
Do you know where you can purchase a new hammer spring
my spring broke on my gun, do you know where I could get a replacement? Great vid btw :)
Depends on where you live, but it’s out of stock in a lot of places. See if the airsoft store you bought the gun from order a spare spring for you.
Got two from red wolf airsoft dot com, most everyone else is sold out, mine actually came in the mail today and im on the video to make sure i put everything back in proper order 😂
@@AshVsEvilFred RedWolf is showing sold out for me
@@TacoSlayer06 ah shit i mustve got the last two. Im sorry brotherb
@@AshVsEvilFred it's all good. I've ordered a bunch from a UK site so I should be set
Will this works in webly mk4
Hi, I am interested in the color of your Colt, did it come that way or did you customize it? If you did that your self did you video the process? I would love to do that to mine, is it a type of case hardening? What ever it is it is SICK!
Thanks, this is the blued version of the revolver. The finish is already there out of the box, not self-made. However some of the blue colour will be lost after a while, especially when you’re frequently handling the gun with bare hands. And start showing the bronze underneath.
Hey I have an issue, my hammer is a bit wobbly when it’s in the resting position. The gun works fine tho. the hammer just goes back and forth a little while all the way forward. Please answer!
It’s supposed to. Since the sear is not catching the hammer at this position.
Question why in your opinion does the trigger not go in flush?
You mean flush with the rear of the trigger guard?
Thanks you so much dude. You just saved my gun. How hard it is to do a full dissemble? Would be cool if you could do it. Cool video dude.
You can checkout this video for further disassembly : ruclips.net/video/o06woiSyUp8/видео.html
where do you buy inner parts and tools to open?
Hardware Stores
Great video! Does the second grip come off in case one obtains spare umarex grips, or perhaps wishes to engrave or customize the grips that come with the gun? Thanks.
You can see 2 small Philip screws holding the other half of the grip once you pop the left-hand side one. Unscrew those and it’s removable.
Awesome! Thank you so much. You earned yourself a subscriber :)
Obvious pseudonym Thanks for the support 😎
@@SemperReloading No problem :)
@@SemperReloading No problem :)
Thanks, I'll remember this if I ever have an issue with my SSA Colt.
What screwdriver did you use when deconstructing this?
Phillips Screwdriver
What are the most common leak issues and how can I fix them?
Addison Schraeder Most of the time it’s caused by over tightening the CO2 cartridge and damage the rubber seal of the chamber. If your gun is leaking CO2, better check the condition of rubber seal. Of course it’s the best to seek help from an airsoft technician.
How did u get that finish and how do you tighten the barrel?
Keven Hughe The finish comes with the gun. And if you need to tighten the barrel, add some seal tape to where the barrel and the frame are connecting.
@@SemperReloading between the slight gap?
Keven Hughe Yes, take the barrel out first. Apply some seal tape to the connecting point.
from my experience, the finish is shit though. it got really ugly for me for literally no reason, most the bluing came off the cylinder and grip for me
Very informative, great job!
Where can I find a spring on the trigger I lost mine
Try to find an Umarex/Wingun distributor at where you live and ask them if they can order the part for you.
My english is not good enough to understand the verb « fanning » in that case, what do you mean that can be harmful to the gun?
Branleur Et Fanning means holding down the trigger and pull the hammer down repeatedly. Because of the revolver is single action. When the trigger is held down and you pull the hammer down repeatedly, the gun will keep shooting like a full auto gun.
It is harmful to the gun is because it puts a lot of stress to the hammer spring. Causing the spring will break.
Mag Tactics thank you for your answer!
I got mine yesterday and the cartridge ejector didn't work , thanks to your vid i managed to dissassemble and re assemble the gun. And i fixed the ejector! Works like dream now
Are the little sheriff badges on the grips metal or stickers? Can I easily remove them?
It’s a piece of metal. You can take off the grip and try to use a small screwdriver to get it out. But I don’t recommend this since this will leave a hole on the grip.
@@SemperReloading oh, alright. Thanks, I'll file it down then so it just looks like a piece of metal, maybe patina it. Thanks tho
what screwdriver is that? i cant unscrew the top right screw and its probably because all of my screwdrivers are too thick to fit in the hole.
Try a small size philip screwdriver.
@@SemperReloading I don't have any smaller ones sadly
Can you still fan it from time to time
Thanks. I'm going to try this. My spring is messed up and it has zero tension. Do you thing I just need to replace it? I will admit that I fanned the gun. Cheers
Probably yes
@@SemperReloading thank you
@@ryderpoulin4875 If you have trouble finding one then go to co2-handguns.freeforums.net/ there's a guy that sells them in the sales section and posts worldwide.
@@ShaunShearman thanks. But I ordered one already, if it doesn't work I'll check that one out. Thanks 👍
Did you fan the gun alot
Does anyone know where I can buy the spring on trigger? I lost mine
How do you remove the right hand side grip on these Medallion grips without the screw?
marshal madsen You should be able to spot the two small phillips screws that are securing the right-hand side grip once you popped out the left hand-side grip. Losen those screws and you’re good to go.
Mag Tactics Thanks mate. That’s good to know. I’m getting a Duke SAA soon. Once removed can you put a fake ivory with screw in the middle in?
marshal madsen If the Ivory grip comes the right screw, it should be okay.
Is there any place I could order a new one? Mine broke
Chris Chiquito Try Evike.com, they still have the smoke wagon version.
Mag Tactics thanks I’ve found similar parts, I’m gonna buy some of them and update if they fit and work
@@forkknife3942 where did you find them?
@@juanpepe2458 www.evike.com/s/?q=Springs&x=0&y=0#?keywords=Springs&search_return=all&Category0=Accessories+%26+Parts here
you can get replacement springs, I make them, message me if you're interested
My experience with all of these Co2 guns is that they work for about 3 or 4 cylinders before they malfunction, exit all the air and are broke - and they are hard as heck to replace the seal gaskets in them which run about $20 - so I just throw it on the pile with rest of them as they are just junk.
Do you know where I could get a replacement spring for the second spring you took off?
Not sure. Most of parts of this gun is very rare to get.
you can get replacement springs, I make them, message me if you're interested
フレームカバーをきちんと蓋が出来なくてグリップが閉まらないのですがコツを教えて下さい
Can somebody post a link to a replacement hammer spring would be much appreciated
Diesel Power So far I only see airgunspares.com carry the spring. But it’s out of stock now.
you can get replacement springs, I make them, message me if you're interested
why isn't the cylinder removable like the original gun?
Manos Zervos There’re several generations of the Colt SAA. The removable cylinder version is a more modern version. You only get this version of replica from Tanaka. The Umarex SAA is replicating the older version of the SAA.
It actually is possible to remove the cylinder.
How do you take out the cylinder
After you open up the tigger compartment, remove the rod which is at the center of the cylinder. Then the cylinder should be freed.
Mag Tactics thx
Mag Tactics is there a way to not open up the gun but remove the cylinder
UNNOTICED Since the gun is based on the older version of the Colt SAA, the cylinder can’t be removed without disassembly.
So since my cylinder doesn't move it is broken and I have to get a new part
Yeah I was fanning the hammer and my gun is broken
Same
I did that too, it's been broken for over a year.
you can get replacement springs, I make them, message me if you're interested
@@Wylfinadi you can get replacement springs, I make them, message me if you're interested
@@geckoeater you can get replacement springs, I make them, message me if you're interested
What screwdriver is that
T.D.P Phillips screwdriver
Mag Tactics thanks so much
I’ve been using one that I thought works but haven’t seen progress
Mag Tactics do you know what size
T.D.P No sure about the size. I just pick the one that fit the job.
Mag Tactics because I have a thing stuck in the cilinder and I can’t open it with my screwdrivers
Why does the replica have smaller, different screws than the original firearm? The big ones on it are decorative and only for the original feel....
4 screws of mine are like impossible to get off. Mine drop on the floor and no gaz is going on it anymore. :-/
LiquidSnake268 Probably they applied screw glue to the screws. Try using a hair dryer to melt the glue first.
@@SemperReloading i try that thx!
Well its works, but still dont know why there is no gaz pushing the bbs 😢everythings works trigger /hammer/ barrel rotation
Oh but everythings on place and now works! Very happy!
I'm having this issue, did the hair dryer end up working or should i use wd-40?
Mag Tactics , would you know what the thread is on the CO2 Capsule retaining screw? Excellent video by the way.
Anybody know where I can get a new hammer spring? Mind broke so I need a new one
you can get replacement springs, I make them, message me if you're interested
do you know how to remove the barrel???
True_ Remedyz Yep, remove the chamber and you will see two removable pins that fix the barrel in place.
I may do a demo about this in the future.
Thanks, I already got a hop up installed. Works great now!
I fully disassembled my King Arms version and it's completely different than this one so it's not like I can follow these steps in reverse like I thought I would lol
I can see a way of putting a steel bar spring steel tension spring in there
Thank you extremely!
I’m having this issue where when I pull back the hammer then it will not fire
at the point you removed the side plate, you failed to point out, the fact that the chamber rotating spring was off the lever arm, ? the reason the chamber was not rotating..but thank you anyway, i have that exact problem with my saa, now i know what must be done.
The spring usually pop off when the plate is out, so be careful when you put it back together.
I know it wouldn’t shoot, but is it possible to make the hammer fully close cause technically in real life that gun wouldn’t shoot a thing
Try filing down the connecting point of the trigger sear and hammer sear.
@@SemperReloading that could work! do you also maybe know any other airsoft/BB/pellet single actions that don’t have the screwed up hammer? I’m very picky I know but just curious
@@legonstuff1748 I’m afraid you have to go for the Tanaka SAA.
@@SemperReloading ahhh ok, thanks!
You can fix it by taking a ziptie and some rubber bands zip tie the rubber bands too the back of the trigger works like a charm you can trouble shoot the best place to put it I put the zip tie threw the center of 3 small rubber bands than I move it undee the trigger works like a charm!
thanks a ton!
I dont know why but after disassembling, my safety doesnt work. It just got loosen and lock/ unlock by itself. Can u help me? As i know . there wasnt specific spring or pins when i removed the safety . there was only safety part to remove and put back in
There supposed to be a black rubber ring thing attached to the safety. If it’s not attached properly then the safety will not stay in place.
@@SemperReloading after i read ur reply, i searched all over and i found one square- ring in the shell-frame that i disassembled from main part, and i have no idea how it was stuck in there,anyways ive found it and fixed it well thanks to you, ty for replyin even tho it's the video that has been some time.
Anybody know how to get a wooden grip for this? The one on mine is not comfortable and it's slippy. Also it deserves wooden grip
How do you remove/refit the barrel
There's two drift pins that need to be knocked out using a small drift, you punch them out from the left side to the right. I hope that helps buddy.
@@ShaunShearmanThanks for the reply, I see them but one is in a blind hole that doesn't completely go through to the other side.
@@ArgosWarrior The lower one is inside the frame, you have to remove the side plate to get to it. I'll give you a link to a full step by step guide that one of my friends did for our forum co2-handguns.freeforums.net/thread/893/colt-saa-loose-barrel-repair?page=1
Go and have a read of that buddy, that'll tell you everything that you need to know.
@@ShaunShearman Awesome, thank you very much its very much appreciated.
I put gun oil mime and it stop working
Does anybody know where I can get a replacement hammer spring in the U.S.A
If the gun is completely locked it's probably the drum catch or part 791.
What a great video I subscribed just for this ❤️
Thx so much
So u cant fan this gun?
Jojo Chua It’s not recommended if you want the gun to last longer.
hi i have a problem with my colt as the chamber spin very freely and has miss fires what in yuor opinion has broken
charles collier By miss fires, you mean that the hammer goes off without pulling the trigger?
@@SemperReloading no I mean it does not fire the bb as it gets stuck between the chamber and barrel its not the c02 has its new but even when in safety mode the chamber is still sloppy .is it a spring issue or something more sinister. the hammer goes down three clicks before firing as it should but on half cock the cylinder spins very freely and I am seeing c02 coming out between chamber and hammer on firing it worked spot on the last time I used it it also fired the first two bbs perfect before problem arose many thanks ROD
U can fan just kinda hurts
My hammer doesn’t shoot, is this the video I need?
Now how to make a new hammer spring if the stock one broke lol
Try ordering one from the store that you bought the gun from.
@@SemperReloading can't find the part
@@stevelevesque676 Yea it’s not widely available. You may have to search for multiple stores.
Have you or will you do a video on modifying the large hammer gap, which really spoils the look of the pistol 😡
The Lone Ranger It’s supposed to be there. There’s a spring attached to the hammer to create this gap, so that the gun won’t shoot all the CO2 out in one single shot.
@@SemperReloading thanks for the reply and like. Yes I know the gap on the Umarex is suppose to be there for the reason's that you said, but the real Colt SAA doesn't have the gap.
Now some owners of the Umarex have modified it greatly reducing the gap and not had the problem of touching the pin value therefore not venting Co2 off, it just make the appearance look 100% better.
Why I think you should have a go at doing the modification is because your RUclips videos are really well done on the camera work and your commentary too is very clear and precise. I'm very sure that if you did the video on reducing the gap to the quality as the original video then once word gets out about the video then your RUclips views will sky rocket and possible subscriptions also.
Something to consider my friend 🤔🙂
The Lone Ranger My Umarex SAA is actually FUBAR for a while 😂, that’s why I don’t make videos about it anymore.
The Lone Ranger If you’re still looking for an airsoft SAA, I’d recommend the Tanaka version. The internal is better designed than the Umarex version.
@@SemperReloading showing my ignorance here what is FUBAR? Is you SAA not an Umarex Colt ?
if you re blue the barrel and cylinder , the rest would get away with looking case hardened ,
so my order for fanning hammer is useless then , shit..
WE HAVE THE SAME GUN SAME COLOR OF THE GUN AND THE SAME HANDLE ILL SUBSCRIBE TO YOU
La verdad muy falso ver cine muy ruido muy fuerte
Z
I need a replacement hammer spring for the cowboy rifle that Umarex has, anyone know where I can find one?
@@rainytigerr I still need help finding a replacement, can you send me the link?
@@rainytigerrcan you send me the link also?