OMG I found the floor boards of my dreams on this website!!!!!! I just said yesterday I was done with the RGS, so time to buy another bike and start all over. Thanks Steve, you created a monster. 😛🤪😜
yes we run the XL OE Boards on the softail project..I have install videos on it....check them out ruclips.net/video/gRY6LK3um_s/видео.htmlsi=KtaBimGFkpfXC2Da
hey to each their own...a clean tank looks good too. I just get alot of questions on how to make sure they are on correctly if you do some back on. Thanks for checking it out!
Alternate method. Just pre heat the badge a little with a heat gun or hair dryer, then use dental floss under the badge in a sawing motion. Clean the residue off with isopropyl alcohol. Polish. Done.
I pulled the trigger today and ordered the Chrome badge for my '23 Ultra Limited and run me about $107 after tax. My plan of attack is to mark the top of the old badge before I remove it and ise that mark (maybe a sharpie) as a guide to place the new badge. Then use my 10" buffer to take any goober adhesive off.
I toggled back and forth between badges on your vid. That looks way better than the original badges. Thought about doing my 2022 ultra limited- apex paint bike. Looks like I'll pull the badges off in the morning and see if I need to get badges or not. I do have badges the same size as the ones you put on and they are the color of my stripes. I was going to put them on the passenger floorboards, my girl's suggestion, but once I taped them in place both of us didn't like it.
Another great video! What disk/ brush do you recommend to use to get the glue off? You used a yellow one in the video. Do the different colors represent different grit or stiffness? Thanks for all the years of great content!
aaah yes I forgot to link it...fixed it..but I use the whizzy wheel from amazon ...the one you seen in the video has already been used several times on my bike trailer...and lots left..they last pretty good. here is the link amzn.to/47hoIDb
Hi Steve, I got my badge from JH Choppers yesterday as well and they do not fit flush on the tank. I sent an email and they referenced your video for placement. I learned about JH Choppers FROM your video, but I rewatched your placement very closely and they do not fit flush. Unfortunately I need to return them and will try RickRaks. Just wanted to pass the feedback along because I love your videos, thanks all your for the content!
The bike looks amazing the tank Look great.But my opinion, I liked it without him.And you took the old Harley ensembles off and cleaned it up.I thought it looked awesome.Thank you again 41 of your videos
yeah dont use the bottom speed nuts...take your side covers off where you can get to the back side and use regular bolts, washers and nuts on there ...slide the bolt in from the battery side and out the washer and nut on behind the deflector...its tight but you can do it
never had luck with it...just pry it off and clean it up has always worked best for me...but then again I may have had some cheap thin line as well..maybe some stronger line would work better.
Im just curious as to if I placed them right they look great but don't lay on the tank to flat...there are still parts of the badge that aren't even touching the tank...ever encountered this or do I need to re do them?
Sorry for the late reply...been at Tail Of The Dragon for a week. I didnt have any bits hanging off the tank...the tape itself will fill in most of the tiny gaps...I would reposition them.
Have you had any issues with your road glide? … I just bought one it has 500 miles and no issues but I’ve been hearing a whole bunch of negative comments
Nothing yet...I dont have a ton of miles on it yet though either. Been reading the same comments...make sure to keep your bike updated at HD if you can...HD is releasing updates all the time for the 2024s
Did you want me to add a yamaha logo? Its a different badge. Clearly I wanted the bar and shield logo and not that one that came on it....Come on man...
It's a good video on how to take the woke logos off. Always love the content bro. Just have a hard time supporting the HD brand since they don't seem to support their legacy.
Looks way better without any badge!
Yes it looks clean without it as well. Thanks for checking it out
OMG I found the floor boards of my dreams on this website!!!!!! I just said yesterday I was done with the RGS, so time to buy another bike and start all over. Thanks Steve, you created a monster. 😛🤪😜
yes we run the XL OE Boards on the softail project..I have install videos on it....check them out ruclips.net/video/gRY6LK3um_s/видео.htmlsi=KtaBimGFkpfXC2Da
How many of you stopped the video after the debadging because you had zero intention of putting a badge back on?
hey to each their own...a clean tank looks good too. I just get alot of questions on how to make sure they are on correctly if you do some back on. Thanks for checking it out!
There was more to watch?
Nice job. Looks good!
Thank you for checking it out randy!
Nice paint color looks good with the black
Thank you Phil!
Thank you so much. Just bought this exact bike today and this is number 1 on my to do list
Very cool...the new bikes are growing on me...Ive got a lot of mods in store for this one.
Fantastic video and the bike looks a lot better with the new badges
Thank you Richard...much appreciated !
That looks a lot better, IMO.
Thanks for checking it out Mike
Thank you Steve!
yes sir!
That bike is 🔥. Looking forward to your updates your making.
Thank you! Ive got parts coming in right now...itll be a bit before everything gets here but we have lots of plans.
De-badging is a good idea these days!
No badges looks super clean..thanks for checking it out.
Awesome video Steve!
Thank you for watching Scott!
Awesome video bud. Well done … thank you
Yes sir..thank you! Love these badges!
Air brushed design would look good for me
thanks it works great !!!!
Thank you for checking it out.
Got mine in today and went to install them but there’s a pretty good size gap 🤦🏻♂️. So these are a no go for me.
weird did you contact him and ask him about it?
@@sikbaggers I text last night haven’t got a response yet.
@@jeremyallen4828 aah ok...ill hit him up and ask him about it
Alternate method. Just pre heat the badge a little with a heat gun or hair dryer, then use dental floss under the badge in a sawing motion. Clean the residue off with isopropyl alcohol. Polish. Done.
yes that will work too....there are several ways to do it...thanks for checking it out!
I pulled the trigger today and ordered the Chrome badge for my '23 Ultra Limited and run me about $107 after tax.
My plan of attack is to mark the top of the old badge before I remove it and ise that mark (maybe a sharpie) as a guide to place the new badge.
Then use my 10" buffer to take any goober adhesive off.
I toggled back and forth between badges on your vid. That looks way better than the original badges. Thought about doing my 2022 ultra limited- apex paint bike. Looks like I'll pull the badges off in the morning and see if I need to get badges or not. I do have badges the same size as the ones you put on and they are the color of my stripes. I was going to put them on the passenger floorboards, my girl's suggestion, but once I taped them in place both of us didn't like it.
yeah ive got these badges now on 3 baggers...they are sharp....mock them up on the tank and see how you like it before you stick them.
Another great video! What disk/ brush do you recommend to use to get the glue off? You used a yellow one in the video. Do the different colors represent different grit or stiffness? Thanks for all the years of great content!
aaah yes I forgot to link it...fixed it..but I use the whizzy wheel from amazon ...the one you seen in the video has already been used several times on my bike trailer...and lots left..they last pretty good. here is the link amzn.to/47hoIDb
Hi Steve, I got my badge from JH Choppers yesterday as well and they do not fit flush on the tank. I sent an email and they referenced your video for placement. I learned about JH Choppers FROM your video, but I rewatched your placement very closely and they do not fit flush. Unfortunately I need to return them and will try RickRaks. Just wanted to pass the feedback along because I love your videos, thanks all your for the content!
yeah just let him know
Looking good
Thank you john!
TY Steve 💯
Youre very welcome and thank you for checking it out!
@@sikbaggers yes sir always
The bike looks amazing the tank Look great.But my opinion, I liked it without him.And you took the old Harley ensembles off and cleaned it up.I thought it looked awesome.Thank you again 41 of your videos
Hey Bill...thanks for checking it out and yes no badges at all looks super clean too. I agree.
do you have advice on heat deflectors install on 2024 RG????
yeah dont use the bottom speed nuts...take your side covers off where you can get to the back side and use regular bolts, washers and nuts on there ...slide the bolt in from the battery side and out the washer and nut on behind the deflector...its tight but you can do it
Cool
Thanks for checking it out Mike
I have never heated it up - just fishing line only. Just keep it in a "sawing" motion and fishing line works just fine. No heat needed.
never had luck with it...just pry it off and clean it up has always worked best for me...but then again I may have had some cheap thin line as well..maybe some stronger line would work better.
Im just curious as to if I placed them right they look great but don't lay on the tank to flat...there are still parts of the badge that aren't even touching the tank...ever encountered this or do I need to re do them?
Sorry for the late reply...been at Tail Of The Dragon for a week. I didnt have any bits hanging off the tank...the tape itself will fill in most of the tiny gaps...I would reposition them.
When you find spot on tank you want it
Small bubble level might help insure bar is level
Don’t know, some of us need a little help 😎🇺🇸
yes sir a torpedo level would come in very handy for this. thanks for checking it out!
Have you had any issues with your road glide? … I just bought one it has 500 miles and no issues but I’ve been hearing a whole bunch of negative comments
Nothing yet...I dont have a ton of miles on it yet though either. Been reading the same comments...make sure to keep your bike updated at HD if you can...HD is releasing updates all the time for the 2024s
De-badging is a great idea, but I would not add another HD logo
yeah no badges looks good too...nice and clean..thanks for checking it out
Badges? We don't need no stinking badges!
I do like those.
hhahaha nice...thanks for checking it out Harold! Much appreciated.
I have never had this happen to me! Rubbing alcohol
yeah you can use that too. Whatever gets the crap off so you can stick it..thats why i said you can make your own iso wipe... (iso)propyl alcohol wipe
Why do you rebadge a harley davidson name and in return put on their logo????
Did you want me to add a yamaha logo? Its a different badge. Clearly I wanted the bar and shield logo and not that one that came on it....Come on man...
It's a good video on how to take the woke logos off. Always love the content bro. Just have a hard time supporting the HD brand since they don't seem to support their legacy.
Thanks for checking it out!
It’s a woke bike so what do you expect ? On the. Quality
unfortunately the quality has been declining on Harleys for years....nothing new