Alright mate, wanted to say great work on the video. Very informative, just what we need!! Wish this was out when I modded my rifle, would have made it so much easier! May I ask, does your rifle leak gas when there is no BB racked and ready to fire? Or any leak issues at all? I know there is leakage when racking the bolt but only a little bit. Thanks in advance. And thanks again for the great tutorial!
Hey Skr333t, before the fixed air seal it would leak under pressure no matter what. When the seal was fixed it was sealed completely both cocked and safe.
@@skr333t5 Sorry for the late reply, been rather busy. The seal that failed is on the front of the cylinder. It just pushes on. The issue is when i used the ptfe tape i think it didn't have the same sealing effect due to the grease. in the end, the only real way would be to either replace the seal or them send a new part. That's what they ended up doing.
i know im randomly asking but does anyone know of a tool to log back into an Instagram account? I stupidly forgot my login password. I would love any tricks you can offer me.
Hey your Video was great for me ! One question - i cant screw the front screw from the triggerbox all the way down?! Othetways the cylinder scratches and stuck. Do you know why? If i let the screw out everything works perfekt..
Hey @pascelpellinger239 The screw is very specific to that slot. Be careful you haven't mixed it up with another one. If it scratches on screwing it in then i would double check.
What trigger do you have in ssg Is it 45 or 90 I'm looking to get the kit for well mbo3 I'm not sure on trigger if I order standard vsr10. What shop did you order from?
@@vytautas2521 From the trigger i fastened it outside then into the pouch. As i had so many issues with it i didn't bother to tidy it up as i never used it on a site. I only tested it to make sure it worked.
@@aprilhamlincom18 Hey i did get a new front seal and it was much better, however with the co2 bulbs being a pain in the arse with consistency etc i put the rifle back to its original configuration.
@@christopherjohnvilan2108 They sent out a new seal. This fixed the problem. The issue i had after that is the consistency of the Co2 bulbs, so i set it all back to the original config.
Alright mate, wanted to say great work on the video. Very informative, just what we need!! Wish this was out when I modded my rifle, would have made it so much easier!
May I ask, does your rifle leak gas when there is no BB racked and ready to fire? Or any leak issues at all? I know there is leakage when racking the bolt but only a little bit.
Thanks in advance. And thanks again for the great tutorial!
Hey Skr333t, before the fixed air seal it would leak under pressure no matter what. When the seal was fixed it was sealed completely both cocked and safe.
@@s1sriggs Thanks for your speedy reply. The air seal in question - is that the one you mention you put tape on and re-greased?
@@skr333t5 Sorry for the late reply, been rather busy. The seal that failed is on the front of the cylinder. It just pushes on. The issue is when i used the ptfe tape i think it didn't have the same sealing effect due to the grease. in the end, the only real way would be to either replace the seal or them send a new part. That's what they ended up doing.
i know im randomly asking but does anyone know of a tool to log back into an Instagram account?
I stupidly forgot my login password. I would love any tricks you can offer me.
@Luka Ezekiel instablaster =)
Hey your Video was great for me ! One question - i cant screw the front screw from the triggerbox all the way down?! Othetways the cylinder scratches and stuck. Do you know why? If i let the screw out everything works perfekt..
Hey @pascelpellinger239 The screw is very specific to that slot. Be careful you haven't mixed it up with another one. If it scratches on screwing it in then i would double check.
does the spring have to be that strong ? I wonder if one would change the spring with a lighter one to make it more quiet and easier to pull....
You could replace the spring, but you have to take the power v distance etc into consideration. A lighter spring could reduce the performance.
Does that spring need to stay in there because i've seen a few snipers that have hpa kits that have no resistance on pull at all.
@slifer967 hi, it is part of the kit. I always fitted it as it allows the gun to spring the cylinder back.
Hello, how many times can a bottle of CO2 be activated? Can you adjust the initial velocity?
small co2 bulbs allow about 20 ish shots. you adjust the power with the regulator.
What trigger do you have in ssg Is it 45 or 90 I'm looking to get the kit for well mbo3 I'm not sure on trigger if I order standard vsr10.
What shop did you order from?
JB, Im using the CNC'd trigger unit on the 24. www.skirmshop.co.uk/springer-custom-works-s-trigger-ssg-24-mod-24.html
Think this would work with a full thrust kit?
@erictaylor4597 To be honest i don't think so as the piston is different i think.
can you show foto where u drilled on body for hose?
Vytautas, i didn't need to drill a hole. I put it into a pouch on the stock.
@@s1sriggs so where hose was going from triger box?
@@vytautas2521 From the trigger i fastened it outside then into the pouch. As i had so many issues with it i didn't bother to tidy it up as i never used it on a site. I only tested it to make sure it worked.
I really enjoyed your video. I have an ssg24 myself, which kit did you use. I can't find it on mancraft's site.
Hey gmcret 142 i used the kit from www.skirmshop.co.uk/tags/mancraft-ssg24/
please make a video how it shoots, how far? and how many shots is enough for an average airhead
Hey Mamed, i would love to however ive had to order more seals as its leaking.
Any updates? Interested here, too ...
@@aprilhamlincom18 Hey i did get a new front seal and it was much better, however with the co2 bulbs being a pain in the arse with consistency etc i put the rifle back to its original configuration.
@@s1sriggs hi do you have any updates on this?
@@christopherjohnvilan2108 They sent out a new seal. This fixed the problem. The issue i had after that is the consistency of the Co2 bulbs, so i set it all back to the original config.
Would this work with a ssg10a1?
Sorry Demon, it's only for the ssg24. The A1 is based on the vsr
is it possible to use this kit on SW24 or not ?
On the SSG24? Yes. I would go HPA though and not use Co2.
do you have a link to the regulator you used
Apologies but it seems the reg is no longer on the site.
Great one thx for the Video!
No problem Serge
good video.thx
Thanks Marcus, bit old but relevant.