We got a spinner 1530 and you'd have to restart the Machine like 5 times and then manually turn a screw to retract the gears....remind you its a Machine from 2016...so this is awesome to see !
hello, I have a vf 11 from 2008 and the cambox is broken. Can you tell me how to make it so that I can make a manual change in the program without leaving the program in MDI
ok I have 2 of these mills where I work and 1 has the double arm spin counter clockwise which makes sense to me because the force of spinning would push the tool into the arm but the other has a problem dropping tools and the arm spins clockwise. is there any way I could change the direction it spins?
Ever figure out a solution? We are currently getting this error in my shop and the automatic recover is not fixing it. Thank you in advance for any advice.
Hello suraj, The grease we're using here to lubricate the various parts of the SMTC and the tool holder is Red-i extreme pressure grease. But most high quality high pressure industrial/automotive greases will work fine as well. The important thing is to apply the lubricant regularly so these surfaces are not making contact in a "dry" state. Thanks for the question.
What if it alarms when there are 2 tools in the arm? It stopped and alarmed mid tool change. The arm didn't drop down far enough to push the pin and release the tool for manual removal. Both tools are in the arm, but one is still in the spindle and the other is in the pocket. It's a 2008 VF4, and it just makes me nervous to continue with the recovery instructions, because none of them mention the situation the arm and tools are in
Throw Away - It's hard to be 100% sure without inspecting the machine and checking diagnostics, but the way you've described it the control would recognize that a tool change was started but the TRP (tool release piston) switch was never reached. So recovery step one should be to slowly lower the double arm until the that switch is reached, meaning you should be able to remove the tools at that point. I know you posted your comment yesterday so you've probably tried something by now, but if you haven't hopefully this helps. Haas Automation
@@haasautomation Thank you for your reply! I ended up choking the rapid to 5% and tried pressing the ATC REV button (with my fingers crossed) to get the arm out of the way. I had to press it about 10-15 times until the arm rotated back to its origin, removed the tool from the spindle, and finished the recovery. The pocket went back up, and everything worked as normal. Hasn't done it since.
Same problem - tool was inserted incorrectly and both are stuck. Automatic recovery fails, and does NOT give an option for manual recovery. Tool release won't work since the tool is still in the arm. Releasing the arm lock manually while pressing tool release doesn't achieve anything either. Can't put pocket up as other tool is in that one too. Ugh@@throwaway8962
Next time let's see a cat 50 machine with a 4"dia by 8" long face mill on 1 side and a 2 " carbide ball endmill in the other. let's see ya one arm them out! 😎
Grease should not be used, because grease is tough, will cause dirt or iron powder to adhere and damage the pull ball stud set. Using oil and air to blow dry enough to be better
Thank You HAAS ! I Ran into this conundrum last night about 30-minutes before end of shift so I had to pass it off. Texted my dayman this video.
Thank You Andrew. That was really well done and extremely informative
very helpful. tks. day 2 on a vf2ssyt, and I got the 2066 alarm. within 5 minutes I was able to start running again.
We got a spinner 1530 and you'd have to restart the Machine like 5 times and then manually turn a screw to retract the gears....remind you its a Machine from 2016...so this is awesome to see !
hello, I have a vf 11 from 2008 and the cambox is broken. Can you tell me how to make it so that I can make a manual change in the program without leaving the program in MDI
ok I have 2 of these mills where I work and 1 has the double arm spin counter clockwise which makes sense to me because the force of spinning would push the tool into the arm but the other has a problem dropping tools and the arm spins clockwise. is there any way I could change the direction it spins?
Olá o magazine travou com 2 ferramentas grande parou fora de posição posso executar esse procedimento para colocar o magazine na posição inicial.
Thanks for the information
Very useful tips! Thanks you sir.
does anyone have any info if the tool is still in the spindle and the arm hasnt gone down yet as you cant move the arm down only up
MUCHAS GRACIAS POR EL VIDEO ME SACO DE APUROS
Our VF3 mill with a 40 taper has this frequent tool changer error: tool changer has timed out.
what is the recovery procedure?
Ever figure out a solution? We are currently getting this error in my shop and the automatic recover is not fixing it. Thank you in advance for any advice.
Yo you a life saver bc i didnt want to bug kno one on my shift to assist me with my oopsy lol self relient kinda
Thank u.
Which was the lubricant you applied on tool holder?
Hello suraj,
The grease we're using here to lubricate the various parts of the SMTC and the tool holder is Red-i extreme pressure grease. But most high quality high pressure industrial/automotive greases will work fine as well. The important thing is to apply the lubricant regularly so these surfaces are not making contact in a "dry" state. Thanks for the question.
На русском можно
What if it alarms when there are 2 tools in the arm? It stopped and alarmed mid tool change. The arm didn't drop down far enough to push the pin and release the tool for manual removal. Both tools are in the arm, but one is still in the spindle and the other is in the pocket. It's a 2008 VF4, and it just makes me nervous to continue with the recovery instructions, because none of them mention the situation the arm and tools are in
Throw Away - It's hard to be 100% sure without inspecting the machine and checking diagnostics, but the way you've described it the control would recognize that a tool change was started but the TRP (tool release piston) switch was never reached. So recovery step one should be to slowly lower the double arm until the that switch is reached, meaning you should be able to remove the tools at that point. I know you posted your comment yesterday so you've probably tried something by now, but if you haven't hopefully this helps. Haas Automation
@@haasautomation Thank you for your reply! I ended up choking the rapid to 5% and tried pressing the ATC REV button (with my fingers crossed) to get the arm out of the way. I had to press it about 10-15 times until the arm rotated back to its origin, removed the tool from the spindle, and finished the recovery. The pocket went back up, and everything worked as normal. Hasn't done it since.
Same problem - tool was inserted incorrectly and both are stuck. Automatic recovery fails, and does NOT give an option for manual recovery. Tool release won't work since the tool is still in the arm. Releasing the arm lock manually while pressing tool release doesn't achieve anything either. Can't put pocket up as other tool is in that one too. Ugh@@throwaway8962
I HAVE VF2 I MACHINE ATC PERFORMANCE VERY POOR...! I WANT SPEED UP ATC WILL YOU PLEASE UPDATE THE NEW VIDEO FOE THAT BEST SOLUTION.
Big thankyou
My machine is stuck with a 941 error after. After resetting the pocket list with the origin button. ‘03 vf2b
How do you get to manual Recovery mode?
Thank you haas
wheres mark?
Great!
Next time let's see a cat 50 machine with a 4"dia by 8" long face mill on 1 side and a 2 " carbide ball endmill in the other. let's see ya one arm them out! 😎
nice tutorial
This is a total pain on OKK machines with Mitsubishi controllers. You have to run a dozen different m codes in mdi to return the arm and pockets.
I cant recover the tool How can i jog z axis up?
That's great for user . !
Thank you sir
thank!!!!
Grease should not be used, because grease is tough, will cause dirt or iron powder to adhere and damage the pull ball stud set. Using oil and air to blow dry enough to be better
if only DMG had videos like this
they only like to sell service
где русский?