Thanks for your job! Dear Kendin, how much take-off weight can operate this motor, I mean aerodynamics (wing), not copter configuration. Thanks again, your channel is really extremely laconic (in the best sense of the word), informative and useful for practicing DIYers! Good luck and good new videos!
hey man, if you are still interested in, the video is published now and only the motor has 140gr thrust power and can fly an airplane which has even 300gr weight.
I am confused by your comment. A Solid State Drive has no moving parts, unlike a Hard Disk Drive. I assume you were taking apart a Solid State Drive instead of Hard Drive.
Elinize sağlık çok güzel olmuş. Bütçesi olmayanlar için zamanınız olursa hurda aletlerden böyle drone veya uçak yaptığınız videolarda çekebilirseniz çok mutlu oluruz
I have a foldable cart of which I added plastic panels on the bottom, front, back and sides. The sides fold inward to allow the cart to fold, but they got in the way at times due to flopping around. So I took the strong magnets from 2 dead HDD's, and used them to keep the side panels in place. Parts of the cart eventually broke but were held back together with old metal HDD mounting adapters that are now being used as clamps. The 2 HDD cases then became the base of a home made desktop lamp.
2:45 - nice solution. Funny thing is you can't hit those motors out on HDD models after 2008. Those are hard-pressed. I tried hammer and round chisel and it just breaks the bottom with top separating. So it will become an open mess with winding sticking out. Older ones, however, were salvageable - you could either hit them out or just unscrew them.
I'm no expert at all but my guess would be to divide the positive and negative cables and keep the same signal cable so they run at the same speed, the motor would have less power but maybe 2 of them can make up for it
the motor is 3 phase ac you need 2 brushless speed controllers run the motors in opposite directions with cw and ccw propellors for no torque on the aircraft
02:22 WD'lerde motor 4 telli değil miydi? Hiç motoru 3 telli olan WD Hdd'ye denk gelmedim. Üç telli motoru Seagate'den başka kullanan yok diye biliyorum.
İki tane harddisk açtım. Biri 4 telli (Birini boş bırakıp 3 teli kullanarak aynı sonucu alabilirsiniz.) Diğeri 3 telli. Kafa karıştırmaması için 3 telli olan ile devam ettim.
Gerçekten çok güzel bir içerik olmuş, eldeki hurda diskler bir işe yarayacak sanırım. :) 15000 Rpm çalışan eski server diskleri var, onların motorları daha iyi sonuç verebilir mi acaba ?
First of all, thank you for sharing your video and also the STL files of the adapter. My HD, in the central part, where the adapter should be fitted, measures 12.5mm in diameter. If I'm not asking too much, would you be kind enough to edit your STL file, in this central part, to 12.5mm in diameter? And, if possible, could you share the edited file here with me? My advance thanks.
Güzel bir içerik olmuş. Teşekkür ederim. Açıkcası elimde söküp beklettiğim 6 adet 4 çıkışlı metalden bağımsız 7200 rpm hdd motor mevcut. Aynı 35a ucuz sürücülerim var. 3 çıkış olduğu için denemedim. Onlarla sürülme ihtimali var mı?
Çalışır. 4 çıkıştan birini bağlamıyorsunuz. Ama bir kaç deneme yanılma ile hangisini boşta bırakacağını bulmanız gerekiyor. Genellikle dıştakilerden bir olur.
Its ok for some light applications but not powerful enough to be real rc model motors, it is designed to handle 2A maximum, the real ones can handle 20a, 30a, 10 times more powerful, nice video though
@@ShinjuNLG definitely, generally RC cars need more torque , even powerful RC car motors use down ratio gear to increase torque while keeping current low, this hard disk motor is more suitable for light drones or slow RC planes and boats with gears . It simply can't handle high current which is commonly required by RC helicopters, cars, speed boats. High current like 10a will burn it quickly for sure.
Vertical thrust is important for drones. Therefore, HDD motor cannot provide enough power. It is suitable for fixed-wing model aircraft with suitable features.
Thanks for your job! Dear Kendin, how much take-off weight can operate this motor, I mean aerodynamics (wing), not copter configuration. Thanks again, your channel is really extremely laconic (in the best sense of the word), informative and useful for practicing DIYers! Good luck and good new videos!
I'm working on an RC airplane project related to this subject. If I get positive results, I will share the video in the future.
hey man, if you are still interested in, the video is published now and only the motor has 140gr thrust power and can fly an airplane which has even 300gr weight.
Nice video! I find it somewhat interesting that you didn't try an even bigger propeller when the biggest you tested was the most efficient.
Wow 😲😅 17 years old account 😊👍🏻
Nice screwdriver you have 👌
Which one? 🤨🤨🤨🤨
Iykyk
I took my entire hard drive apart and didn't find any motor in it. These solid state drives are useless. 🍻
😂 and how the disk inside move .. ? ..
And they even more expensive ? I mean ...
😂😂😂😂
Try nvme
I am confused by your comment. A Solid State Drive has no moving parts, unlike a Hard Disk Drive. I assume you were taking apart a Solid State Drive instead of Hard Drive.
Hay man for summer you should make a 2 motor boat with a rudder.
şu test düzeneği mükemmel olmuş.
tamamen DIY olan bir rc uçak videosu da gelecek sanırım yakında.
Güzel bir çalışma olmuş.
2A'da 150 gr thrust. Ufak ve hafif RC UAV'lar için yeterli.
Harika anlatım Harika video için teşekkür ederim.. 😍
Çok faydalı bir içerik olmuş, emeğinize sağlık.
hiç aklıma gelmezdi çok iyi fikir olmuş :=)
Elinize sağlık çok güzel olmuş. Bütçesi olmayanlar için zamanınız olursa hurda aletlerden böyle drone veya uçak yaptığınız videolarda çekebilirseniz çok mutlu oluruz
ruclips.net/video/yFBvC_zRiek/видео.htmlsi=bmUZSZFCoLoZLQJM
Kendin excellent work,,,, 👍👍👍
I have a foldable cart of which I added plastic panels on the bottom, front, back and sides. The sides fold inward to allow the cart to fold, but they got in the way at times due to flopping around. So I took the strong magnets from 2 dead HDD's, and used them to keep the side panels in place. Parts of the cart eventually broke but were held back together with old metal HDD mounting adapters that are now being used as clamps. The 2 HDD cases then became the base of a home made desktop lamp.
İlk yorum benden olsun "yine harika çalışma".
2:45 - nice solution. Funny thing is you can't hit those motors out on HDD models after 2008. Those are hard-pressed. I tried hammer and round chisel and it just breaks the bottom with top separating. So it will become an open mess with winding sticking out. Older ones, however, were salvageable - you could either hit them out or just unscrew them.
it's a shame
Okay i'am impressed and i subscribed. Now make a cpu cooler with this motor.
With existing old intel stock air cooler.
The original small rc motors were made from CD rom motors back in the day. It’s a new spin on the old technique.
Great job 🎉🎉🎉
Elinize sağlık. 😇👍
Bu geri kazanım motorlar, radyo kontrollü uçak hobisine yeni başlayanlar için çok ekonomik bir seçenek olacaktır. 🧐👍
When you demonstrate spinning, tape a thin plastic rope (colorfull, 1..2 mm diameter) to the axis and rope opened on the table.
we got rc airplane motor from hard disk before gta 6
Yes dude this is creazy
What does mean
@@sksai4 mean does what
@@SCSmartTech sorry I didn't get what that means
@@sksai4 its fine, it happens 👍
Sir, have you done Aeronautical Engineering?
excelente!! 👍👍
Great idea!! Can you share the motor electrical connection? Which of the 3 wires is which?
If it's a brushless motor, it doesn't matter. If the motor runs the wrong way, just swap any pair of wires and it runs the other way
The middle wire of the motor should be connected to the middle wire of the ESC. The other two determine the direction. It works either way
12v blutooth kit ekakth ekka ena amp ekata supply denna widihak kiyannako eka bass eddi off wenawa chara chara ganawa
kênh của bạn toàn nội dung hữu ích
thật tuyệt vời
try it with a dvd/cdrom bldc motor , it's agressively powerfull, maybe upto 100kV.
Hocam yeni logo güzel olmuş
How can I make twin rc plane with same propeller CW
I'm no expert at all but my guess would be to divide the positive and negative cables and keep the same signal cable so they run at the same speed, the motor would have less power but maybe 2 of them can make up for it
@@joejoe2974 the motor is 3 phase ac you need 2 brushless speed controllers
the motor is 3 phase ac you need 2 brushless speed controllers run the motors in opposite directions with cw and ccw propellors for no torque on the aircraft
Nice to meet you
very nice
Motorlarla fpv drone yapılabilir mi
02:22 WD'lerde motor 4 telli değil miydi? Hiç motoru 3 telli olan WD Hdd'ye denk gelmedim. Üç telli motoru Seagate'den başka kullanan yok diye biliyorum.
İki tane harddisk açtım. Biri 4 telli (Birini boş bırakıp 3 teli kullanarak aynı sonucu alabilirsiniz.) Diğeri 3 telli. Kafa karıştırmaması için 3 telli olan ile devam ettim.
Turkiyenin en kaliteli türk kanalı
next video, can you make a mini drill from this HDD?
Finally face revealed 😂
Birde normal bir brushless motor ile deneseydin keşke, aradaki farkı görürdük.
maybe rewind the stator with thicker wire to handle more current??
I did that 20 years ago but now for $10 you can get a much better lighter motor with mounts a prop driver and connectors ready to plug into the ESC
Can You tell me type and manufacture of screw driver?
Bosch Go
Gerçekten çok güzel bir içerik olmuş, eldeki hurda diskler bir işe yarayacak sanırım. :) 15000 Rpm çalışan eski server diskleri var, onların motorları daha iyi sonuç verebilir mi acaba ?
Muhtemelen daha torklu olabilir. Ve devirde yüksek. Daha iyi sonuçlar olası.
so cool
First of all, thank you for sharing your video and also the STL files of the adapter.
My HD, in the central part, where the adapter should be fitted, measures 12.5mm in diameter. If I'm not asking too much, would you be kind enough to edit your STL file, in this central part, to 12.5mm in diameter? And, if possible, could you share the edited file here with me? My advance thanks.
Güzel bir içerik olmuş. Teşekkür ederim. Açıkcası elimde söküp beklettiğim 6 adet 4 çıkışlı metalden bağımsız 7200 rpm hdd motor mevcut. Aynı 35a ucuz sürücülerim var. 3 çıkış olduğu için denemedim. Onlarla sürülme ihtimali var mı?
Çalışır. 4 çıkıştan birini bağlamıyorsunuz. Ama bir kaç deneme yanılma ile hangisini boşta bırakacağını bulmanız gerekiyor. Genellikle dıştakilerden bir olur.
abi ellerine saglik ***
Hey brother kendin can you answer to my question how do I study the aerodynamics and thank you so much your my inspiration ❤❤❤❤❤❤
Great airplane, this one is stealth, right?
???????
Did it ever get of the ground ? :p
bununla drone yapımı videosu çeker misiniz
Can I make drone with this motor?
No problem
Yes it is light weight than drone motor ❤
Not enough rpm
Needs to be atleast 20000 rpm
Can fly a drone with such 4 motors?
How I build the motor out
I have built models from you several times, can you please build an F22 Raptor😊
Diy asmr😮😊
Can you share the 3D STL Files
The link for the propeller adapter is below the video.
@@Kendin-Yap your homemade propeller holder
1:41 😂haha
😂😂😂
Its ok for some light applications but not powerful enough to be real rc model motors, it is designed to handle 2A maximum, the real ones can handle 20a, 30a, 10 times more powerful, nice video though
But what if used for small rc cars? Maybe with some gearing down?
@@ShinjuNLG definitely, generally RC cars need more torque , even powerful RC car motors use down ratio gear to increase torque while keeping current low, this hard disk motor is more suitable for light drones or slow RC planes and boats with gears . It simply can't handle high current which is commonly required by RC helicopters, cars, speed boats. High current like 10a will burn it quickly for sure.
Lesson to learn: electric mcrewdriver is must
Is it possible to make a drone with 4 HDD motors 🤔
Vertical thrust is important for drones. Therefore, HDD motor cannot provide enough power. It is suitable for fixed-wing model aircraft with suitable features.
Can you make drone this mator
If it can make helicopter can definently make drone
Abim motoru vida yerinden nası çıkartacaz vida sökülmüyo matkapta yok
Should recycle from broken and no any signal for the HDD and the motor still useful XD.
Keep it up your half way there to the speed you need to fly a plane lol, motor I just put on mine runs at 22,000 rpm
no wonder, bcs 1Tb but refurbished hdd... 😁
HDD nin açılmış hali nedir
Может и не полетит, но раздуть мангал точно сможе, о а это идея😅 уж лучше точилки для гвоздей😊
I was expecting this to be a joke like the “how to make a cpu” video
Die Idee ist ja gut...
Aber eine 1TB Platte würde dafür nicht opfern😢
It must be a broken one like mine. And its capacity doesn't matter. It can be any broken HDD. 😊
Am i thế only one not seeing an RC aeroplane ✈️
This is not a plane video. It is a RC plane motor video. As stated in the video title..
This airplane as huge capacity 😂
we saw his face!!!!!
:)
maybe not for Rc plane but as a air fan only use
wow
👍
Also use a broken drive not a working one
Your videos are awesome but after looking at it for a while it makes me very frustrated.
This is not a rc aeroplane, right?
This is a RC airplane motor video. Not an RC airplane.
132 g az ama mikro bir rc uçak yapılır sanırım
Bununla ilgili bir uçak videosu düşünüyorum.
@@Kendin-Yap merakla bekleyecegim
Как мини мотор колесо
they are not really suitable for airplane
Why use 1 tb hdd why why why!!!!!!
There is no particular reason why I chose 1TB. Among the HDDs I have, it was the only one with a lot of "bad sectors".
MacGyver
3pm
I will sell that hard disk and buy a rc motor for cheap, time and cost efficient.
not enough torque to weight ratio to make it useable even in the lightest of breezes, would not recommend
If U can't even build a plane to fly with this kind of thrust, skill issue. It's already so high, considering a 2amp current draw
kkkkk a kalvice do fera kkak mu!to f3IO
you made the most important part the shortest...
Güzel fikir, peki işe yarar bir şeyler yapılabilir mi? Teknik bilgim olmadığı için soruyorum.
Nice to meet you
very nice