Funny how i remember being a kid and have an old ass washing machine that never had any problems. Now they start making them digital and the problems are endless. I might see if i can find an old one again
I used to fix my Kenmore washer and dryer everytime a part wore our or some other issue (not many overall). Loved that they were dependable and that I could do the repair if needed. Sadly we replaced the washer when it beyond my ability to repair and bought a 700 series. The lock problem is the most prevalent on it and now it keeps skipping to Complete a minute after it starts. Too frustrating. Miss that old washer!
i have the 700s kenmore and it finally started doing this after 8 years. so thats why im here. thanks bud im haveing an issues with it not spinning now.
I have same washer purchased in 2018 . When you start a load it locks lid and begins then suddenly unlocks to add a garment. I start again and same happens eventually it continues with the washing cycle. When turning knob to select cycle it doesn’t work consistently either.
Same machine mine says E3F5 I read somewhere something about the locking mechanism but how would I go about checking? How did you get this into diagnostics mode? You went very fast on pushing the buttons.
I have a top loading Kenmore 700 series triple action he washer machine it goes thru the cycle and everything but the clothes do not come out clean at all. It fills and drains but it isn't working. No error code
Does anyone know what model this is or does anyone know how I can find the user Manuel cuz I lost mine and I cannot find this exact one anywhere online
I have this same washing machine and it just stopped working. After I push start I hear the lid lock and the basin starts to spin but it’s making a knocking sound and hardly spins very slow, so it doesn’t even get thru the process of weighing out the load or adding water and the knocking sound is pretty bad. Water never even begins to fill up the basin and after a few attempts to spin & weigh the load, the machine just shuts off. Don’t know what’s causing this cuz I know nothing abt repairing these types of machines. I watched your video but I’m not sure how to initiate such a test. If you have any advice that would be great & super helpful. Thanks
I have this same machine it only will fill to about 5 gallons on normal cycles does this machine have a load sensor and if so where is it located also the pressure switch is mounted on the main board and doesn't seem to have a way to adjust It can anyone help with this it has no error codes
Nope lots of complaints on this machine some complaining that some clothes don't actually get wet during the wash cycle. What people are doing now is adding water manually.
@@joeradke7522 if the magnet can't fit into the lid lock switch, you'll have to find much smaller to fit it in, so that way you can bypass it. but remember, push the lid lock latch halfway, so that way it won't cause an issue
The Wash Temperature is at Hot The Soil Level is at Extra Heavy The Spin Speed is at Max Extract Options Selected are Oxi, Extra Rinse, and Deep Clean. Audio Level (High, Low or Off) is optional.
Shift actuator, unless the machine is not agitating either that's either a dead motor or capacitor. the capacitor and shift actuator are fairly cheap to replace so that would be where you look first.
Funny how i remember being a kid and have an old ass washing machine that never had any problems. Now they start making them digital and the problems are endless. I might see if i can find an old one again
I used to fix my Kenmore washer and dryer everytime a part wore our or some other issue (not many overall). Loved that they were dependable and that I could do the repair if needed. Sadly we replaced the washer when it beyond my ability to repair and bought a 700 series. The lock problem is the most prevalent on it and now it keeps skipping to Complete a minute after it starts. Too frustrating. Miss that old washer!
Had an old school one and fixed the Heater strip that burned out qnd worked flawlessly after ! Bought is used.
i have the 700s kenmore and it finally started doing this after 8 years. so thats why im here. thanks bud im haveing an issues with it not spinning now.
Thank you so much. You saved me a service call!
Thank you! You helped me
I have same washer purchased in 2018 . When you start a load it locks lid and begins then suddenly unlocks to add a garment. I start again and same happens eventually it continues with the washing cycle. When turning knob to select cycle it doesn’t work consistently either.
Same here just changed the lock switch hoping that would fix also drained with commercial vacuum nothing
Same machine mine says E3F5 I read somewhere something about the locking mechanism but how would I go about checking? How did you get this into diagnostics mode? You went very fast on pushing the buttons.
I have a top loading Kenmore 700 series triple action he washer machine it goes thru the cycle and everything but the clothes do not come out clean at all. It fills and drains but it isn't working. No error code
Hi! By any chance do you have a video on how to factory reset the board? My machine steam is not working, what could it be the problem?
How do you test the water level. Mine seems to have a low water level when washing
Same
@@hotgirlbummer520 That's the complaint you'll have to add manually.
Same to me it only use like 2 tablespoons of water I hate this washing machine..
welcome to the new washers @@mayragonzalez502
Does anyone know what model this is or does anyone know how I can find the user Manuel cuz I lost mine and I cannot find this exact one anywhere online
Ran diagnostics and it failed 005 which it is the pressure sensor. How do i open the control panel to replace the sensor?
What’s the model number?
@@joshuajhagroo9096 110. 28132414 you should’ve pay close attention to the text in the beginning
I have this same washing machine and it just stopped working. After I push start I hear the lid lock and the basin starts to spin but it’s making a knocking sound and hardly spins very slow, so it doesn’t even get thru the process of weighing out the load or adding water and the knocking sound is pretty bad. Water never even begins to fill up the basin and after a few attempts to spin & weigh the load, the machine just shuts off. Don’t know what’s causing this cuz I know nothing abt repairing these types of machines. I watched your video but I’m not sure how to initiate such a test. If you have any advice that would be great & super helpful. Thanks
i think is the washer drive belt ,is in the bottom of the washer .
@@SergioGonzalez-qu3vv Not the drive belt. these machines are direct drive.
Any update? Mine is doing the same
@@kellym4753 suspension springs
@@SergioGonzalez-qu3vv Don't say shit. it doesn't have any belt
Same washer but mine dosent seem to be getting the clothes clean. Maybe not Agitating
No not enough water add water manually.
Same happen to, it's like is washing with like 2 tablespoon of water...
Could you do the sanitize cycle if you can on this machine?
Mine only blinks the diagnostic mode then goes off
I have the dryer version
I have this same machine it only will fill to about 5 gallons on normal cycles does this machine have a load sensor and if so where is it located also the pressure switch is mounted on the main board and doesn't seem to have a way to adjust It can anyone help with this it has no error codes
Nope lots of complaints on this machine some complaining that some clothes don't actually get wet during the wash cycle. What people are doing now is adding water manually.
I tried the diagnostic and mine says E2/F5 and tips or suggestions on what I can do?!?
Lid lock
I have this machine and it's got code f7 and E9 what do I do and what's the issue.thank you
Locked rotor
My 700 series Kenmore is not starting
On the test mode, the clothes would have the worst rollover with the agitation.
if it's too slow for agitation, they probably won't come out that clean. even strong agitation can clean kind easily
cdn.appliancepartspros.com/images/product/cache/frigidaire-washer-drive-belt-134511600-ap3867042_01_l.jpg
Samsung WW900 washing machine end tune
My machine keeps saying f5
Where did you get that magnet?
I found it on the other side of her fridge. So this way I can defeat the switch
How do you recalibrate the washer
@@ryanswashervideos6052I can’t get the machine to bypass the lid lock with the 🧲
@@joeradke7522 if the magnet can't fit into the lid lock switch, you'll have to find much smaller to fit it in, so that way you can bypass it. but remember, push the lid lock latch halfway, so that way it won't cause an issue
@@ryanswashervideos6052 bought new switch, good as new
Tengo una labadora Kenmore 600 pero el sistema no funciona solo ase un sonido como q BA alabar que ago
Tengo una que no deprime que ago
The Wash Temperature is at Hot
The Soil Level is at Extra Heavy
The Spin Speed is at Max Extract
Options Selected are Oxi, Extra Rinse, and Deep Clean. Audio Level (High, Low or Off) is optional.
I tried test number 10 but the washer is not spinning, what would that issue be?
Shift actuator, unless the machine is not agitating either that's either a dead motor or capacitor. the capacitor and shift actuator are fairly cheap to replace so that would be where you look first.
Oh yeah I don't have that
Que significa E6 y F8
Basket frozen after spin cycle
SI jalo la labadora