Many Do Not Know How To Weld Aluminum, Cheap and Fast
HTML-код
- Опубликовано: 26 дек 2022
- #welding #automotive
Many do not know how to weld aluminum, cheap and fast
many don't know how to weld aluminum other than tig welding, there are many ways to weld aluminum, one of which is in this video
These repairs have been around since oxyacetylene was integrated into the auto repair shop. It' s called gas welding. I do it all the time. Two thumbs up. 👍👍
That turned out much better than I thought it would for cast aluminum. Well done
Lets X-ray it.......
@@jpsholland yeah, it won't pass inspection, but it is functional for his needs
Todos son fundidos
Magnesium mix
@@jpshollandwhy?
Those castings are dirty anyways.
That's why a lot of people won't fool with them.😊
Well I guess as it's only a cover a full strength weld is not required, however I'm not so sure just giving it a quick brush covers the fact it should be spotlessly clean before attempting to weld or in this case solder a huge chunk of material over a split .
For a flywheel dust cap fix, this weld is very VERY good! A little grinding and it'll be like new. Whoever says the opposite must be one of those guys from the bad clan of welders who are always alarmists, criticize beginners and think that if you weld a piece of crap you have around you're useless if it doesn't have the integrity of a nuclear reactor.
Agree. After dressing up and polishing the repair will be fine.
Or, they may know the difference between welding and melting. Heating up the aluminum and the smearing the top layer to close cover the crack isn't welding. A weld should be stronger than the material around it. This may work for this application, but per the title of the video, it's not welding more "like" brazing.
@@DualsPortvet absolutely. Now, may I use an aluminimum MMA electrode (without the coating ?) to do such a "gluing" I need to repair a hinge for a bycicle, essentielly the ring is holding the axis in place I suppose a lesser resistance is acceptablme. I heve the aluminium rods, but I am afraid to melt the ring vey easily .. Now, is it possible to solder copper or bronze commer on the aluminium of that bycicle frame ? THANKS (a lot)
It won't survive a little grinding
Tig сварщик вышел из чата :-) Глазам больно.
Y q electrodo estas usando y que tipo de soplete es? Ósea que gas usas en el soplete
Melhor conselho alumínio quebrou joga fora a solda nunca fica resistente. A não ser se for soldada com gás argônio e a vareta com a liga certa prá aquele tipo de alumínio.
I weld alluminium via Tig usually, i'm going to try flame as well.
I'm figuring out you need a very reducing flame and the iron rod is used to mix the melted joint ....
The iron rod is used to swirl the base metal and filler?
I think the iron rod is to get out impurities. I think that's why you hear him always tapping, I think it's to flick impurities off the rod so he can melt some more and pull out more impurities with a freshly flicked and clean rod lol
Na verdade ficou bem feito o serviço parabéns sorriso mt Brasil
Love all the criticism in the comments, Arguing structural integrity. Looks like a cover of some sort. I don't believe it's going to be under much stress. Does the job
Mig with spool gun works too. I have used aluminum electrodes with a stick welder. The metal has to be about 1/8 minimum. The thinner the faster you have to go.
I have welded broken outboard skegs back on, and extensions for worn ones, with stick. They disappear fast so you have to feed it in fast and move fast along the join.
I tig that stuff. But looks you did well and looks strong for the repair. Good job
From what i was taught when i was a kid, this was called brazing to me when i was to repair/fill or join weak metals?
Buen trabajo.
what material are you adding ???
لم اعرف نوع او رقم السلك المستخدم في البدايه نرجو الاجابه
شكرا للعمل الجيد
Flacăra nu e uniformă la becul de sudură, deci are zgură pe interior. Trebuie curățat din când în când ca flacăra să fie ascuțită, pentru a concentra temperatura la vârf. Nu înlocuit, ci curățat ! Meseriaș e cel care repară, nu cel ce înlocuiește cu ceva nou ! Pentru eficiență și mai mare, mai ales la sudarea cu GPL (vezi filmul meu, unde modific becul de acetilenă și merg cu GPL care e de 20 de ori mai ieftin) se găurește capul de cupru , de la interior către exterior, cu un burghiu conic, pentru a face gaura conică și să concentreze temperatura în vârful flăcării. Poți înlocui materialul pregătit din alte piese, cu electrozi înveliți din aluminiu. Pasta de pe ei asigură o decapare perfectă, și nu mai e nevoie de electrodul de oțel pentru a sparge oxidul. Bravo, orice-ar spune „specialiștii” , eu te felicit și fă treabă în continuare ! Numai cine nu poate spune că nu ține ! E foarte greu si trebuie să ai mână și experiență, pentru a nu topi toată piesa, în loc s-o sudezi !
Please send your link 🙏
La tecnica es curiosa , el problema que veo yo es que la deformacion de esa carcasa al calentarla provocara una deformacion en los planos que ya no acoplara correctamente ni al motor ni el eje del ciguenal. pero como concepto esta bien. un saludo
The guy is a ACE you can tell good job 👍👌👏👏
hello, but the electrode that you use and for aluminum ? How many degrees does the electrode you are using melt? I wanted to know if I can repair a scooter radiator with an electrode or can I try with durafix type rods? Thank you
He wasn't using the rod as filler. He was using it to get nice and hot, and mix the base metal under the dross, flicking it off. Once he had it hot and 'melded', he came in with some filler aluminum. You'll notice he went back and forth, removing the oxide layer with the electrode first.
Muito bom amigo parabéns 👏 👏 👏
Muy bueno☺👌👍
Ainda vai mostrar o lixamento e pintura?? O acabamento final???
wat rod you used as filler metal?
Hey what kind of rid are you using there?
Pretty amazing as what he accomplished. I hope in the future that he will clean the part first.
I can't resist, what is the AWS specification for his filler rod? 🙂
Hangi elektrotu kullanıyorsun ???
Quais são os tipos de eletrodos?
Estou iniciando com solda agora .
Esse tipo de solda é com gás argonio no maçarico com vareta de alumínio. Fique curioso me parece perfeito pra soldar peças mais frágeis
Gases oxigênio e acetileno.
What rod did you use?
Top-Job, Sir👌
Lets test it. Where are the X-ray's?
Existe vareta de solda própria para antimônio 😉 desde 1987.
fazendo dessa forma que ele fez é muito melhor, comprei varias varetas que não dão liga, fiz dessa forma do video e deu muito certo.😉
Também já comprei mas só consegui esquentando a peça
I would have squeezed that case together to fill in crack then grinded a bit to have really clean metal
om Itu pake borak atau ngga ya supya Gampang nyatu 🙏🏻🙏🏻
Pues no entiendo mucho de esto pero creo q la pieza debería ser ajustada para q las grietas curren y soldar para q está no quede descuadrada
Eso ya es otra cosa
Aquí solo enseñan a soldar
A clean tip helps with the heating
M gustaría q dijera o replicará q tipo d varillas usa
Привет, какой газ ты используешь?
That looks to be a magneto cover, of a small motorbike engine, that weld wouldd be plenty sufficient
Hola! Desde Argentina cuál es el material de aporte ?
om kalu kloter kerengker bagian drat dan dalem nya bisa ngk?
beau travail !
A great job! Would like to know what kind of rods you used because that seems the key to success! please share thank you,!
Hey Bud, did he tell you what kind of rods he is using in the video? Cheers 🙏
@@Tz_ziar no! not yet!
He uses the electrode (flux covered) rod just to push and mix the metal. The alumium he uses looks like recycled stuff. Better to use a quality aluminium welding rod. All alumiium welding rods are not the same.
Tambien se puede sordar con semiautomatica con sistema mig
What gases are you using ???
Itu pakai kawat las apa bang..mohon info nya bang.
Muy bien, un saludo
I stick welded a riding lawnmower blade mounting bracket. On two blade mower. I’m bad at cleaning. But I got the new aluminum rod hot. Enough. I goobered it up. And kept grinding cuts with. Dirty grinder wheel. Lol. But I penetrated good enough. Old man whent strait back to rock pile I told him not to. It held. Lol lol lol. The the more high tec welds . Like bike frame . I would clean more and get gas shield blowing on it. Or more flux. Good enough job.
Che tipo di elettrodo usi?
После такого глобального перегрева детали, её повести должно, думаю что посадочные отверстия могут не сойтись.
Судя по мастеру,он потом эти отверстия либо рассверлит большим диаметром либо молотком вколотит болты. Перегрев детали? Неее. Не слышал🤣
Это не коленвал а обычная крышка картера, нечего не будет
O serviço ficou lindo, aparência muito boa. Gostaria de saber sobre a funcionalidade da peça recuperada. Fechou direitinho, houve vazamento? Essas peças costumam deformar com muita facilidade.
If weld properly,its wont leak and deform,in the video u can see he using,stick rod to remove the oxidation layer after he welded,so the pure aluminum will remain fused..and yes,this is the cheapest way to do the engine cover repair..
راءع ولحام جميل جدا جدا هل تستخدم مساعد لحام
Лучше я буду не уметь, чем так уметь.
Горячий газ водоростей,, и да все прекрасно верится, применение в судостроении, газ водород очень опасньій. По етому такая сварка применяется на предприятиях имеющих установки по производству водорода.
Это не сварка, это пайка алюминия, припой типа А5 или зарубежный аналог кастолин, кабельщики и холодильщики пользуются подобной технологией пайки алюминия с 60х-70х годов, а мастер конечно Красавчик, руки из плеч, результат впечатляет, дороговато конешно 1 пруток кастолина в нашем регионе 750р. деревянных + пропан 1350р. 50литровый балон+кислород 1200р. Отсюда и ценник за такую работу конский, помоемому берут 500р. за сантиметр
Если кромки соединяемого металла плавятся это по любому НЕ пайка. Иначе отличить пайку от сварки станет не возможным
Совершенно верно! )) Это пайка , наложение припоя на поверхность металла ... Сам холодильщик))
Не разу не паял алюминий, но мне что то кажется он паял оловом
Не , это припой по влюминию...Паял в 90-х годах оловом испарители алюминиевые ... Оловом чтобы паять нужна ещё железная стружка , чтобы разрушать оксидную плёнку....Алюминий поэтому тяжело паяется из-за оксидной плёнки...
@@user-zx8up4qx7zпару лет назад сам понял радиатор мотоцикла сузуки (знакомый просил), понял автогеном пропановой горелкой, припой А5, зачистил железной щёткой, затем грел радиатор и втирал как-бы этот припой, получилось неплохо, до сих пор катается.
Well done Mr 😎
it's just a lid, a cover with a crack that does not seem to have the purpose to hold a great mechanical stress, so, that quick fix in this case (only) is good enough if you don't want to buy a spare part
Ciao, i m italian, che spessore hanno le bacchette di alluminio?
Mohon maaf , apa jenis elektroda yang anda gunakan pak 🙏
Que tipo de gas es y de q barilla
Ahora as un video como desolda el aluminio ya que la tapa no coincide, ya que no serraste la grieta devesti apretar con la prensa.
apa aja yg disiapkan alatnya om untuk las alluminium sperti dividio🙏
Mantap , hasilnya bagus kawan.👍👍
Hola una pregunta cual es la herramienta con la que calientas el aluminio ? Algún tipo de soplete o como se llama
Hola Noel, este soplete va con dos botellas uno con oxigeno y el otro acetelino/ otro tipo de gas.Mezclando el gas con el oxigeno hace una llama de altissimo temperatura.
Since Indonesia and the Philippines are like one race, bara-bara na lang bai hangang mabutas!
Well if it works then fair enough. However, I see the gap distance tolerance would be out and it looked warped. I guess the angle grinder is your friend😅
In order to restore the part qualitatively, it is necessary to eliminate the gap in the crack by tightening the crack with a clamp.😉
Mate, qualitatively , thats the first time ive ever seen this word used... wouldn't quality have done.?
Aside from avoiding potential weld defects, clamping would ensure that the part fitment should be the same (or close enough) after repair.
Надежнее синей изоленты ничего нет
@@user-gb3hm1rq8b на большое ума не хватило ?
@@user-gb3hm1rq8b le tenemos más confianza a la vini tape negra japonesa. Revienta cuando quieres que reviente y se estira siempre lo suficiente que presisas en especial en el verano.
Видел я газовую сварку алюминия. Сам сварщик. Свариваю алюминий каждый день. Знаю как это делается. Как то не так 😏подготовка "на высоте "🤣🤣🤣🤣про монолитность шва и отсутствие дефектов можно забыть вовсе. А так то есть электроды для ММА сварки по алюминия, есть миг сварка при помощи полуавтомата))) что быстрее и по итогам дешевле этого творчества... Про тиг на переменном токе вообще молчу. Это по-умолчанию приоритетный тип сварки в ремонтных мастерских... ( без кузовного ремонта)
Не иначе как Пакистан, край изобретателей из г-на и палок. До чего находчивый народ на фоне нищеты.
Сергеич,петля от стилалки сломалась,вроде силумин..реально спаять или что? Медяшки я много паял..
В середине 80-х варил поддоны от лодочного мотора "Вихрь" точно таким же способом. Флюса или аргона и близко не было. Но поддоны работали, где-то и по сей день один валяется в гараже.
Lasan nya yg di blok mesin di lelehi. Lagi bisa gak om
Диву даёшься! Наверно Индия! Аргона и всяких плюшек, станков и т.п. нет, А Сварка есть. Значит можно,если нужно! Лайк!
это не сварка на видео,а пайка алюминия специальными прутками по алюминию.
Muy informativo, muchas gracias. Ahora SI sabemos cómo soldar aluminio
Una cosa es ver y creer y otra es la realidad
La práctica hace al maestro
Looks good to me 👍😁 well done
Why do you think that ALL leading companies use expensive and hard to use TIG equipment as a third world farmer boy can do it better with prehistoric methods?
Yes it can be done this way, but dont expect any quality compared to TIG welding.
Seems that many don't know how to clean the part that needs welded and the tip that needs cleaned severely, nothing like passing along bad habits
Đã đăng ký kênh rồi bạn ơi 😊
Muito top👍
少し数字的なこと質問しても良いですか、母材の温度はどのぐらいですか、また溶棒の種類は何ですか、本体強度はどのぐらい戻りますか・・・
知りたいことたくさんありますガス溶接でしょうが、アセ、と酸素の割合、圧力等・・・
А КАКОЙ ГАЗ ИСПОЛЬЗУЕТЕ?
I was taught to heat the material up to 700C then let the rod melt into the weld. The alloy melting temp is 1200C. The melted rod will then adhere to the alloy on a molecular level providing a good, strong bond. What he shows is equivalent to spak filler. Not all rods are born equal and youtube Project Farm has tested 3 alum rod brands that work.
1200c? He makes his own rods from recycled cast aluminium it’s not diy solder
Ну это не сварка, это пайка. Знаю, потому что покупал подобные припои и пробовал с помощью газокислородной горелки делать подобное...но стоимость этих припоев и соответственно прочность шва... лучше тогда купить электрод шведский по алюминию и заварить без проблем. А если действительно хотите чуть ли не даром, то угольный электрод от солевой батарейки, сварочный инвертор, флюс для алюминия " Харрис" и вперёд...
how can you preheat Alum. to 700c when that would be 1292f and the melting point of Alum is 1220f.
Swedish aluminum electrode? You have my interest. Have you a link please? Thx.
It’s probably super common alloy casting. Maybe a356. You should preheat it but you should not heat it above 450C. And you have to stress relief after a weld repair like this. Maybe heat to 320C, hold for 30 minutes and then ramp down 30° per hour for three hours. Then remove from the oven and allow to cool in ambient temperature.
Bolong?
Itu pake kawat apa om?
Pemula belajar pengelasan almunium tank 👍👍👍
Hasil nya menakjubkan,
Горелка ацетилен биланми.сим оддий алюминми илтимос ёзинг
What are you using for a filler rod.. It looks like an arc welding rod, but what do you use .. Thanks for your time and information.
I think he is using the rod(iron) as simply a mixing stick to stir the molten puddle together
How solid do you think it was?
Lokasi?
Owh... Seperti itu toh 👍👍👍
Bir klima borusu var eleminyom çok incedir kaynak yapmak istiyorum hiç yapmadığım için sizden biraz bilgi almak istiyorum
Good job 👍
Напряг с метала не снял,а это значит что изделие повело и вы его просто заслюнили. Даже фаску не выбрали. А в целом способ рабочий.
What is this flux for this welding
Hola muy buena la pre sentasio pero me gustaria sa ber si se puede soldar a luminio con una ma quina nor mal osea sol da dura de arco
Vou fazer com esqueiro
Mantab boskuh sukses slalu👍
МАСТЕР!!!
Thanks I’ve always wanted to know what that means so my old Russian rc engine is a “master”
Juuosss sangat bermanfaat
What kind of rod is that ?
Que usa como fundente?
dont listen to these non welding city boy comments ..like grandpa told me sum men see a fire fly and call their self a welder u sir done helluva job
Молодец!
This process is called brazing not welding!
Que gas usan?