Check it Out!! Watch me Build a Wood Laptop Table / Stand / Desk Quick DIY Project!! For anyone asking, here are the dimensions I used Tabletop - 13" x 21" x .75" Fame for the legs - (2) 19" x 1.5" x .75" and (2) 10.5" x 1.5" x .75" Legs - (4) 8" x 1.5" x .75". **If I were to do it again I would make the legs slightly longer, possibly 10". The brace that goes between the legs - 9" x 1.5" x .75" Hope this helps!!
If you suggest to make the legs 10" then I would need to make the frame for the legs slightly longer as well or the legs would not fold inward. What length would you suggest I make the frame to fit the 10" legs?
@@carlosbergante4316 Hey Carlos, honestly didn't think of that when I wrote it.. I was just thinking for comfort to raise the table up a little bit. But, if I were to make one again, I would probably just increase the top to 24". That should accommodate 9" or even 9.5" legs, plus give you a bit more room on the top. For 10", maybe bump it up to 25"-26".
Awesome! I'm an old guy that's gone through stage 4 Cancer and stage 3 kidney disease and I've never been the same. Making a lap table like this is exactly what I need for when I'm reading and writing! Thank you ! 🇺🇸🙏❤
Feeeeeeeeeeeeeeeeeeeeeeeeeeeeennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnttttttttttttttttttttttttttttaaaaaaaaaaaassssssssssssssstttttttttttttttttttttttiiiiiiiiiiiiiiiiiccccccccccccccccccccccccccccccccccccccccc 99% , can you make with a wooden screws , Or wooden studds ( am not sure if this is the right term in Carpentary ) hope you got my question ........ Thank you. :)
Hey! I did just wing it as I went to be honest. The top is based solely on the dimensions of MY laptop with a little extra. Here is what I used - Tabletop - 13" x 21" x .75" Fame for the legs - (2) 19" x 1.5" x .75" and (2) 10.5" x 1.5" x .75" Legs - (4) 8" x 1.5" x .75". **If I were to do it again I would make the legs slightly longer, possibly 10". The brace that goes between the legs - 9" x 1.5" x .75" Hope this helps!!
Hey! I did just wing it as I went to be honest. The top is based solely on the dimensions of MY laptop with a little extra. Here is what I used - Tabletop - 13" x 21" x .75" Fame for the legs - (2) 19" x 1.5" x .75" and (2) 10.5" x 1.5" x .75" Legs - (4) 8" x 1.5" x .75". **If I were to do it again I would make the legs slightly longer, possibly 10". The brace that goes between the legs - 9" x 1.5" x .75" Hope this helps!!
Lol. I was wondering when someone would mention that. Ran out of wood glue and just didn’t feel like going back to the store. Pure laziness. Thanks Russell!!
Here is what I used - Tabletop - 13" x 21" x .75" Fame for the legs - (2) 19" x 1.5" x .75" and (2) 10.5" x 1.5" x .75" Legs - (4) 8" x 1.5" x .75". **If I were to do it again I would make the legs slightly longer. The brace that goes between the legs - 9" x 1.5" x .75"
Check it Out!! Watch me Build a Wood Laptop Table / Stand / Desk Quick DIY Project!!
For anyone asking, here are the dimensions I used
Tabletop - 13" x 21" x .75"
Fame for the legs - (2) 19" x 1.5" x .75" and (2) 10.5" x 1.5" x .75"
Legs - (4) 8" x 1.5" x .75". **If I were to do it again I would make the legs slightly longer, possibly 10".
The brace that goes between the legs - 9" x 1.5" x .75"
Hope this helps!!
If you suggest to make the legs 10" then I would need to make the frame for the legs slightly longer as well or the legs would not fold inward. What length would you suggest I make the frame to fit the 10" legs?
@@carlosbergante4316 Hey Carlos, honestly didn't think of that when I wrote it.. I was just thinking for comfort to raise the table up a little bit. But, if I were to make one again, I would probably just increase the top to 24". That should accommodate 9" or even 9.5" legs, plus give you a bit more room on the top. For 10", maybe bump it up to 25"-26".
Awesome! I'm an old guy that's gone through stage 4 Cancer and stage 3 kidney disease and I've never been the same. Making a lap table like this is exactly what I need for when I'm reading and writing! Thank you ! 🇺🇸🙏❤
You almost look like David Gilmore from Pink Floyd! Super nice job I will make one for the grandkid! Thanks😊
Haha. If only I could play the guitar half as good as him. Thanks!!
nice, got my wood . ready to start mine
Do you have plans/instructions with measurements available?
easy to make at home nice DIY definitely worth to give it a try
Thanks! It's been a few months and still holding up just fine! Quick afternoon project!
Feeeeeeeeeeeeeeeeeeeeeeeeeeeeennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnttttttttttttttttttttttttttttaaaaaaaaaaaassssssssssssssstttttttttttttttttttttttiiiiiiiiiiiiiiiiiccccccccccccccccccccccccccccccccccccccccc 99% , can you make with a wooden screws , Or wooden studds ( am not sure if this is the right term in Carpentary ) hope you got my question ........ Thank you. :)
What angle do you cut the legs?
love the vibe 😍
Super sekali
Hello! I really need something like this but different size like 25x20 can you build it for me. How much it cost?
If you are local to me, sure! I'm in PA.
@@greenhillgraphics I’m in NJ
Great job!
Looks good. What angle did you cut the legs that meet the floor? The angles from the top of each leg look like 45s. Thanks!
Thanks!! Yeah they were cut at roughly 45ish so they’d sit flat when folded out.
What is the total weight of the table?
I enjoyed the bgm. What's the title?
Can you pls provide me sizes of wood needed? Thanks.
Hey! I did just wing it as I went to be honest. The top is based solely on the dimensions of MY laptop with a little extra.
Here is what I used -
Tabletop - 13" x 21" x .75"
Fame for the legs - (2) 19" x 1.5" x .75" and (2) 10.5" x 1.5" x .75"
Legs - (4) 8" x 1.5" x .75". **If I were to do it again I would make the legs slightly longer, possibly 10".
The brace that goes between the legs - 9" x 1.5" x .75"
Hope this helps!!
What's the background music?
Good job. Could you pass me the measurements please? I want to build one just like it for me.
Greetings, from Buenos Aires, Argentina!
Hey! I did just wing it as I went to be honest. The top is based solely on the dimensions of MY laptop with a little extra.
Here is what I used -
Tabletop - 13" x 21" x .75"
Fame for the legs - (2) 19" x 1.5" x .75" and (2) 10.5" x 1.5" x .75"
Legs - (4) 8" x 1.5" x .75". **If I were to do it again I would make the legs slightly longer, possibly 10".
The brace that goes between the legs - 9" x 1.5" x .75"
Hope this helps!!
This is a cool build. Is there a reason you used epoxy over wood glue? Otherwise looks amazing
Thanks! Honestly it’s just pure laziness. I ran out of wood glue and didn’t feel like going out. Had epoxy on hand so I used that. 😉
What is that hardware you used for the legs called?
They were just 1/4 in nuts and bolts. And some washers. Nothing special!!
Anyone knows the music used in this video?
Are you the vocal from the Pink Floyd? :)
buen video muchas gracias por compartir tus habilidades
Thank you!!
👍😀👍
wow nice
Dude can you give me the materials you used here aside from the wood?
Hey! I’m pretty sure I just grabbed some 1/4” bolts and nuts with washers I had. That’s the only hardware.
Thanks dude did you use some varnish here?
Markus Villame no problem. I just used a couple coats of teak oil.
Thank you so much dude
Thanks.
Nice job
+gk diy thank you!!
Ya know they make wood glue. Lol. Nice build though.
Lol. I was wondering when someone would mention that. Ran out of wood glue and just didn’t feel like going back to the store. Pure laziness. Thanks Russell!!
I have ghe table, i just need the macbook
Excelente
Bgm- Time on our side by sebastian
much better if you include the measurements....
Here is what I used -
Tabletop - 13" x 21" x .75"
Fame for the legs - (2) 19" x 1.5" x .75" and (2) 10.5" x 1.5" x .75"
Legs - (4) 8" x 1.5" x .75". **If I were to do it again I would make the legs slightly longer.
The brace that goes between the legs - 9" x 1.5" x .75"
Not enough height for bed or sofa usage ☝️
Give it away . 😀
But wait theres more.... call within the next 10 mins and well include.. not 1, not 2, but.3........
Haha. “Just pay separate shipping and handling”
deixa as medidas d
I'm sure you can find awesome woodworking plans on woodprix
Toonami li ji op all in one table op on playlist stat li ji 8 7 design functions li op 9 0 a