Hi very nice Schematic, would you be able to share the circuit which is also connected via an LDR so the light only activates on IR motion at night, that way the PIR will remain inactive at day time. // Also is it possible for a parallel bypass to put on the light directly by a switch ? It would be great if you can share this schematic please.
How to connect a 12V LED strip light directly to the sensor without using any resistor or transistor or a relay. The LED strip light will be powered by 12V 5A driver. The setup will be mounted underneath the kitchen platform. The LED strip light should turn ON when the drawer is opened. Why are transistor and resistor mandatory? What would happen if remove them and connect LED strip light directly? In case if direct connection, will the strip light get damaged or the pir sensor get damaged? Or neither of these will get damaged and LED strip light won't glow?
Can we use this circuit for room auto lights ON and OFF. If someone comes in the room Light should be ON and stay ON till someone is in the room and should be OFF when someone exit. Same like real life scenario. How to do this?? Please reply.
sir i used the same circuit with 5 v relay , 5 v adaptor , pir sensor bc 547.When i swicth onthe power , relay switched on and bulb on , bulb stays on,. Can you pl tell me whats wrong with circuit. Bulb is not swtching off. I ve done setting of sensitivity and range also , no results.
i used the same circuit with 5 v relay , 5 v adaptor , pir sensor bc 547.When i swicth onthe power , relay switched on and bulb on , bulb stays on,. Can you pl tell me whats wrong with circuit. Bulb is not swtching off. I ve done setting of sensitivity and range also , no results.
Finally someone gave me that content that i wanted..........thnakew soooooo much😀🤩
Welcome 😊
Very successful circuit. I did it. Thank you very much for your excellent explanation.
Excellent demonstration with clear explanation. May Allah/God increase your knowledge and guides you
Thanq so much Lawal Mohammed
So nice thanks the world's best teacher
The world's best teacher please make for us an ampliefied clap switch sir
Nice
you are very good my friend thanks
Thanks @Uski Giri
It's working.😁 Thanks sir.😉
So nice thanks
Very nice👍👍👍
Hi very nice Schematic, would you be able to share the circuit which is also connected via an LDR so the light only activates on IR motion at night, that way the PIR will remain inactive at day time. // Also is it possible for a parallel bypass to put on the light directly by a switch ? It would be great if you can share this schematic please.
ruclips.net/video/2dxhbXHYEG0/видео.html
Subscribed
great work success there family 👏🤝
Good work. Keep it up
So nice
wow...very nice job
thanks for support
Thanks
How to connect a 12V LED strip light directly to the sensor without using any resistor or transistor or a relay. The LED strip light will be powered by 12V 5A driver. The setup will be mounted underneath the kitchen platform. The LED strip light should turn ON when the drawer is opened.
Why are transistor and resistor mandatory? What would happen if remove them and connect LED strip light directly? In case if direct connection, will the strip light get damaged or the pir sensor get damaged? Or neither of these will get damaged and LED strip light won't glow?
TNX BUDDY. What is the detectable range of this PIR Sensor ???
Nice information in details . Thank You
You should reply all the questions
Can you share documents again? The link in the description isn't working
Can I use another 5v relay,like 8pin DPDT 5V RELAY
Yes, you can use.
Is The Process same for the 12 volt dc relay instead of 5volt relay
same. But you need to adjust the voltage requirement for the relay.
Hlo shall we use 9v relay 9v dc supply instead of 5v for this process
How I can use triac instead of relay. It will save space
and money
Anil Kumar Goel
Sir if i give 5v AC supply will it work
Can I use 220ohm resistor
My light is 30 w led and it is frequently getting on and off without any motion
Pls tell solution ⚠️
Will it act in day time?
Sir mazha problem zhala sensar kam karat ny
I want to use led strip. Can you please help to make this with pi sensor? Please answer. 12 v LED strip in place of the AC bulb.
Remove the relay and AC supply. Connect XL6009 module at the output pins, you can get 12 v using this module.
What does resistor and diode do
Can we use this circuit for room auto lights ON and OFF. If someone comes in the room Light should be ON and stay ON till someone is in the room and should be OFF when someone exit. Same like real life scenario. How to do this?? Please reply.
Yes, you can use this circuit as you described.
I tries to hook this up without diode and resistor and it acts like a timer on and off on and off etc
Can l use 12v DC
Supb
sir
i used the same circuit with 5 v relay , 5 v adaptor , pir sensor bc 547.When i swicth onthe power , relay switched on and bulb on , bulb stays on,. Can you pl tell me whats wrong with circuit. Bulb is not swtching off. I ve done setting of sensitivity and range also , no results.
Change the jumper setting and try
I didn't get ckt diagram from, requesting to send
If frasnel casing,not use.what happen.?
Purpose of using the fresnel lens is to broaden the aperture with short focal length. I hope you got the answer.
not working......
pura circute set kiye but light automatic on ho rha h ac supply dene se ......
how to solve problem....
Which ressistense use
820Ω Resistor of 1/4 watt
@@BlueDotElectronics I want to use led strip. Can you please help. Me to make this with pi sensor
👏🇧🇷👏🇧🇷👏🇧🇷👏🇧🇷👏🇧🇷👏🇧🇷👏
Can I use 9v bettry
Yes, you can.
Transistor BC 458 warking
Bhai bulb ko door laga sakte h kya
ha.laga sakte
Can we use 9v dc supply
Plz can you tell
Yes, you can use 9v supply to power the Arduino.
Sir me tumi dhakavla tas kela ahe
Resistor value?
820ohm
Help sir me plz
Still this needs LDR to keep it OFF at day time.
ruclips.net/video/2dxhbXHYEG0/видео.html
are call me ..once ..my duvets clear thanks for your understanding.
Bhai hindi m bhi bola kar english m to hazaro video hiiiii...bhai teri english ki wjah se na jane kitne bhai tujhe subscribe bhi nhi karte hongee ....
Hindi theek se aati hai
Haa, @dilip kamat
hi u good explanation but i have many question can i have your email to conntact you plz
Yes.sure, mail me at CONTACT@BLUEDOTELECTRONICS.COM
i tried but it dosnt work this is my email amroahmed1989@hotmail.com plz contact me and i m electrical Eng i have couple questions Thank you Brother
Nice
So nice
Will it act in day time?
i used the same circuit with 5 v relay , 5 v adaptor , pir sensor bc 547.When i swicth onthe power , relay switched on and bulb on , bulb stays on,. Can you pl tell me whats wrong with circuit. Bulb is not swtching off. I ve done setting of sensitivity and range also , no results.
May be you relay is faulty.
Or pot of pir is faulty
So nice