मेरे दोस्त यह विडीओ हिंदी मे बना बहुत लोग देखेंगे और बहुत को फायदा भी होगा जो इंग्लिश आछी तरह जानते है वहु एक तो खुद सिख लेते है या फिर विदेशी विडीओ हि देखते है आपका नॉलेज excellent है पर हिंदी मे समजाव
Actually u can go to the auto router and check (tick) only the bottom layer and run....boom, then u make ur tiny adjustments. I think auto router is the best....trust me i have done some its fantastic.
Thank you for the good video. Please consider adding a video that explains how to select the mechanical sizes: of holes, capacitors, screw holes, and nets width, etc.
Excuse me for the blunt question, can I know why does EasyEDA does not automatically generate holes/pad for Vcc and GNB which can be used as power supply to the board.
Please tell me another method of doing things I changed pads of components, but after some time I found some corrections I make them and Import changes to pcb layout after this All pad changed as they were very first pcb conversation I stucked If I change pads then I can't import changes, If import changes then everytime I have to change all pads
this is an amazing insight into the build, i just subscribed i also have built a 50 watts, 75 watts panel and 2 wind turbines on my channel successfully
I have a box I purchased which has a 12 pb keypad, I want to take out the original pcb and create my own, repurposing the small enclosure. Is there a way to place pads on the board by using x y measurements so I can place the pushbuttons in the same location as the original board?
Your projects are awsome.. But pls make single layer pcb layouts. Pcb making with copper clad is not possible in two layer pcb layouts, Or please make a video about how to convert two layer pcb layout garber file to single layer using easy Eda software
Brother can you please explain, if i want to take print out of the circuit which i made in easyeda, for pcb etching process. Which option should i need to select in easyeda software? So that I can take print out?
I have a question if u r using a top layer (red) then how can it be just under components how u gonna solder it?? for our small diy projects we have one side copper layer which is the bottom layer(blue), actually we are looking down from top to bottom and the layers help u to control. I dont think the top layer u r drawing make sense here what i mean is we cannot lift the component and solder underneath , looking from top.
Please tell is it possible to change circuit connection in schematic diagram after 90% complition of PCB layout I connected wrong connection in schematic and found it after 90% of completion of PCB tracks layout Please tell me easy way so my PCB layout struggle not go waste Or I have to make whole PCB layout from scratch by stating by placing comments
i cant use bottom layer in eda. when i choose bottom layer and start to wiring, after touching pad automatically bottom layer selection is changed into top layer. any ideas for me?
Very nice tutorial. Is there a way to properly align components in the PCB design. Like, I know it doesn't affect performance, but for example those resistors are a bit misaligned
Thanks for the video. I tried to make a simple PCB with an EDP8266, MAX485, RGB LED and a few resistors. The auto-route gave me an error; attempted: 55, completed 54, failed 1 but there is no guidance where it failed. How can I trace where the error is?
WARNING JLCPCB has a very very bad service, i have order in total 5 project and only recieved 3 of those, the 2 missing NO REFUND ANDNO HELP solving it thay just say just reorder it (with again paying for it)
Please can someone help me out I just maked a schematics on easyeda but when I try to convert it to a pcb it dose nothing I have saved the schematic but it still won’t convert it to a pcb if someone no’s why or can you help please can you or can I email you with a pic to show what it’s doing
![BLACK BAG - Official Trailer [HD] - Only in Theaters March 14](http://i.ytimg.com/vi/Du0Xp8WX_7I/mqdefault.jpg)
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
Finally an easy-to-understand and well-explained tutorial.Hats off to you!
Clearly explaind before this video i was having many doubts but after watching the video my all doubts cleared. Thanks so much
One of the more useful jlcpcb tutorials thank you
its cus hes indian
Fantastic tutorial mate - well done!
`Thank you very much my Friend
मेरे दोस्त यह विडीओ हिंदी मे बना बहुत लोग देखेंगे और बहुत को फायदा भी होगा
जो इंग्लिश आछी तरह जानते है वहु एक तो खुद सिख लेते है या फिर विदेशी विडीओ हि देखते है
आपका नॉलेज excellent है पर हिंदी मे समजाव
Before this video i was having many doubts, but after watching the video EVERYTHING cleared. Thanks so much SIR
Great tutorial. Cheers from the USA.
Awsome bro nice circuit design and software. I like it
Bro..thank you so much. You are really helpful. Cheers from Indonesia.
Very useful tutorial.. Good Explaination thanks for your vedio.. 👌👌
One more tips... in the schematics u can simply select the components and hit the spacebar to rotate really fast.....boom.
Thanks bro for telling an easy way to prototype pcb😍😍😍
I am in search of PCB designing since long time.
Thanks!
Great vedio Sir.......v informative..thanks v much.
Too GOOD and very much helpful
I was waiting for a detailed tutorial.Thanks sir
Thanks for sharing your knowledge.
Helpful video 👍
Great video, but I do not understand what you are doing at 13:05. Can you please explain?
Nice info, well done, thanks for sharing it :)
Je to výborný seriál, zvláště pro začínají pracovníky
Great Video , Thank you 3 years later in July 2023
Very good explanation
Actually u can go to the auto router and check (tick) only the bottom layer and run....boom, then u make ur tiny adjustments. I think auto router is the best....trust me i have done some its fantastic.
Hello friend thanks for help, but tell me One thing if WE dont make copper area is a problem? 😅
Drawing of copper area for both layer is mandatory,for Fabrication??
Thank you for the good video. Please consider adding a video that explains how to select the mechanical sizes: of holes, capacitors, screw holes, and nets width, etc.
Thanks for this video. please Make another video on how to place smd on both side of PCB.
Thank you! Your video was very informational and easy to understand.
Really good video thanks for making it
Such a great explanation thank you
Thanks For Everything
Thank you very much 🙏
Excellent...you cleared many doubts...
Excuse me for the blunt question, can I know why does EasyEDA does not automatically generate holes/pad for Vcc and GNB which can be used as power supply to the board.
Thank you so much for that great tutorial
thanks very good tutorial
Can we able to draw a circuit diagram through observing the already made pcb??
Very useful.
Thanks a lot
Easy HomeMade Projects
!!
Thx so much really helpful
Can I use this software through mobile
thank you for this video and i subscribed your channel..
Please tell me another method of doing things
I changed pads of components, but after some time I found some corrections
I make them and
Import changes to pcb layout after this
All pad changed as they were very first pcb conversation
I stucked
If I change pads then I can't import changes,
If import changes then everytime I have to change all pads
Many thanks ! Great vídeo !
this is an amazing insight into the build, i just subscribed i also have built a 50 watts, 75 watts panel and 2 wind turbines on my channel successfully
Very cearly explained and thank you
keep up the good work.
May i know how much did they charge for the shipping of the boards
Thanx for this video we want this video
I have a box I purchased which has a 12 pb keypad, I want to take out the original pcb and create my own, repurposing the small enclosure. Is there a way to place pads on the board by using x y measurements so I can place the pushbuttons in the same location as the original board?
You can ask their support team.
@@EasyHomeMadeProjects good answer, I will give them an email.
Excellent!!! thank you.
Awesome tutorial, thanks for this useful post..
Your projects are awsome..
But pls make single layer pcb layouts. Pcb making with copper clad is not possible in two layer pcb layouts,
Or please make a video about how to convert two layer pcb layout garber file to single layer using easy Eda software
I want to use it for my4 band graphic equaliser can u guide me how to connect sliding potentiometer I didn't find it in component
I have the same video on my channel and i must say i love your delivery.
Brother can you please explain, if i want to take print out of the circuit which i made in easyeda, for pcb etching process. Which option should i need to select in easyeda software? So that I can take print out?
Watch complete video
@@EasyHomeMadeProjects thanks i got the solution
Great tutorial
I have a question if u r using a top layer (red) then how can it be just under components how u gonna solder it?? for our small diy projects we have one side copper layer which is the bottom layer(blue), actually we are looking down from top to bottom and the layers help u to control. I dont think the top layer u r drawing make sense here what i mean is we cannot lift the component and solder underneath , looking from top.
Thanks a lot for this clear tutorial. That website truly is amazing.
Thank you sir!
Please tell is it possible to change circuit connection in schematic diagram after 90% complition of PCB layout
I connected wrong connection in schematic
and found it after 90% of completion of PCB tracks layout
Please tell me easy way so my PCB layout struggle not go waste
Or I have to make whole PCB layout from scratch by stating by placing comments
Simply make changes in circuit diagram and then click on "update pcb" option under pcb design option menu.
Fantastic explanation thankyou
How to design single layer pcb? how to apply setting in easyeda tool?
how about shipping cost to India
i cant use bottom layer in eda. when i choose bottom layer and start to wiring, after touching pad automatically bottom layer selection is changed into top layer. any ideas for me?
How this app allow us to have components on both sides (especially SMD components) thanks
Good job.
Thank you doen sharing and like🤩
Bhai agr mota diode lgana ho to holes size kaise bdega
Thank you dear friend I am Arabic follower on RUclips
what are the components to create a circuit for WIFI? or internet interface.
thank you is very good
Bro please make audio amplifier
Powder filling machine please
Hi, can you do a tutorial on how you did the bottle filling machine project, please.
If they had this when I was in school I might have stayed in Electrical Engineering!
Very nice tutorial. Is there a way to properly align components in the PCB design. Like, I know it doesn't affect performance, but for example those resistors are a bit misaligned
Yes, it can be done. Select the components (by pressing and holding the Ctrl key) and, go to the top menu -> Format, and select the desired alignment.
Can you eliminate a lot of the ground tracks via a ground plane?
Hi
How to Add Interactive Html Bom to easyeda
Nice information
Great thank you brother
Hello how much do you charge to make a gerber file for me ? I need to Oder some PCB thank you !
WHAT IS THE OPTION TO CONVERT JLC PCB
How can i check my schematic is free from error.. And is ready to convert in pcb
Thanks for the video. I tried to make a simple PCB with an EDP8266, MAX485, RGB LED and a few resistors. The auto-route gave me an error; attempted: 55, completed 54, failed 1 but there is no guidance where it failed. How can I trace where the error is?
Left side, design manager
WARNING JLCPCB has a very very bad service, i have order in total 5 project and only recieved 3 of those, the 2 missing NO REFUND ANDNO HELP solving it thay just say just reorder it (with again paying for it)
Sir please tell me how we find the circuit diagram
sir, how can i get components pad layout print?
Please can someone help me out I just maked a schematics on easyeda but when I try to convert it to a pcb it dose nothing I have saved the schematic but it still won’t convert it to a pcb if someone no’s why or can you help please can you or can I email you with a pic to show what it’s doing
How do you do that routing
What does "unfinished net" mean?
Thank you for the lesson. is it possible to convert png format circuit download from the Web?
How to take dc 15 voltage
Thank you so much
Dude, hit the space bar to rotate a symbol. You're welcome.
Sir mere liye pcb design ker sakte hai
PCB is $4 and shipping is $50 dollar....this is not workable.....Any other solution?
Hopefully the factory in China can handle files in pdf format
Can I use auto routing option
Yup
Camical ko kis chiz me dale
How to get this software?