I heard others with same issue i cant complain i never have trouble getting it off be sure rack slide first then try to get it off or slide lock it then hold pins down and release slide release :)
@@AirsoftNLD believe me, I’ve tried everything. It gets stuck just at the start of the rails it runs along, after the hammer. Once it gets there, I have to pull the trigger at the same time as pushing the slide forward with force. Which is really something I don’t want to do because then I have to reset the trigger by hand by pressing down on the levers which can’t be good.
I don’t know if I’m doing something wrong but when I do it the same way my Glock slide will go only a inch forward then it’s locked In place and won’t unlike in the video?
I have the same glock as the video i think but the two pins that you pull down when taking off the slide, my pins dont move at all and i put force on em. I also heard in a video they are just for show? but then how do i take off the slide
Is it silicon spray you are using to lube the parts? Sorry if its bad english😅 you are teaching in a way that i understand what you are doing. An how many times in a month do i have to clean it?
Hey man, thanks alot! You immediately notice an icreased smoothness. I use it everyday and repetitively reload the mag, pull the slide and blank fire. Like a toy to figet with if that helps to give you an idea. How often would you recommend cleaning in my case?
What oils/lubricants go on what parts? I plan on getting a maintenance kit from Nostveritch and was wondering if I should just use silicon grease on all the moving parts. I don’t wanna mess up anything.
Hey I've had mine for over a year and have never been able to use it because it won't shoot.. I load everything but when I pull the trigger; nothing..at times BBs dow just roll out of the barrel as well.. do you have any suggestions?
Hey so I just got this airgun. Sometimes when I shoot the bb doesn't come out and then I pull the trigger next and it shoots 2 bbs. Also sometimes when I notice it didn't shoot the BB will just be loose inside of the gun, I will then pull out the mag and the bb will fall to the ground.What am I doing wrong or is my gun defective? I just got some gun oil to put on the CO2 cartridges to see if that is the issue. Is my magazine defective?
Love the video. I have a question my 19x is not feeding my BBs and the side stays back after the first shot. If I want to slide to move forward, I have to push it from the back of the slide. The funny part is if I have no babies in the magazine and dry fire, it works fine.
I hope that you or someone who knows the answere is answering me 😅 So 1. that one black screw that holds the nozzle unit down and also the rear sight and that black plastic thing in the back. This one screw gets loose every time I shoot or just load the gun a few times. What do I do about it? EverOne seems to have no problems with that except me... and I’m trying to use lock tight right now and hope it helps. And 2. does it damage the hammer if I dry fire it? No gas, no mag or at least mag with no gas and bbs In it. Because I did it a lot and I think I took it to far... the triangular bearing on the hammer scratched of a bit of metal in the hammer housing and also bent the part where it sits in a bit. So does it come from me dry firing it without gas? Or am I just unlucky cus the screw that holds the spring to pull back the nozzle also just went loose and got fired out with one shot and the gun is still just a few days old but that’s not really my fault cus I didn’t do anything, never even took it apart before that happened...what am I doing wrong 😑??? P.S: does it damage the hop up unit if I accidentally double feed the gun (one round chambered in and reload again)?
lol idk about the screw i dont have that. that lock tight might be a solution. or maybe send it back lol. theres diffrent opinions on dry fire. i dont like to do it. some say it damages your pistol some dont. so i just dont do it. double feed should not be a problem i do that loads of times lol. maybe u can send it back for repair if its really that bad.
*One way to take the orange tip off* take the barrel out of the gun, boil up some water, then stick the barrel in the boiling water. Let it simmer in the water till you think it’s good (this heats up the glue and softens it up) take a pair of pliers or channellocks then pry it off. This is only if you can’t take the orange tip off from RUclips videos you see. This is one way
My man they both glocks all airsoft umarex glocks are the same only diffrent jacket. All on you. If u like the 19x then take that. I like them both. But i rather have gen 5 glock. Bigger in size.
Eerst en vooral een leerrijke vlog 👌. Ikzelf heb 4 glock's : - 1 glock 17 gen3 - 1 glock 17 gen4 - 1 glock 17 gen5. En ook nog 1 glock 19X coyote. Ik moet kiezen welke ik hou,de gen4 of de gen5 ? Comments en antwoorden zijn welkom. 👋
I think I commented on one of your videos before, I recently got a glock 17 gen 5, and I'm looking to get either a GLOCK 19X (6mm) or a GLOCK 45, which one seems more reliable too you?
I bought the Co2 version and the slide release will not move and I can’t remove the slide. I called service and they say it is NOT supposed to come apart. I have the gen 5 version bought Oct 2021. Half blowback version. Anyone have any suggestions?
Lock slide back hold both pins down release slide it will get stuff less than half way so just pull trigger when it gets stuck then it will easily slide right off
@@infamoussnake4042 I have the same pistol with the same problem. What he is saying is that the takedown pins don't move at all. It seems that umarex has made this pistol now ment to be taken down at all as even the hop up adjustment would get in the way of the slide moving forward and would need to be taken out. Would have been nice I'd that was made clear in any of the videos receiving the pistol online
Hello the plastic peice next to the outer barrel chamber thing is loose it's not coming out but it's very lose the more I shoot it the looser it gets how to fix it?
Hey my inner barrel is a bit loose I can move it with pliers. Is that normal? My outter is very lose but I think it’s been like that from the beginning
Tried taking the slide off the way you did and it got stuck. Now the barrel is stuck and won't let the slide go back all the way and I cant take it apart. Any ideas?
Very helpful and one of the few disassembly videos for the 19x. Any lower frame disassembly videos out there? For the life of me cannot find a single set of instructions or a video for this model. Thanks!
Hey I was wondering have you ever came across an upgrade for the Hop Up ? I'm trying to make this a bit better of a pistol for outdoor to get more distance on my shots.
I'm maybe late but it's designed that way since the real glock barrel tips up to load the next bullet more easily but I think most of the handguns has it. Although it won't affect your aiming since the inner barrel won't move
heb je ook een video van de rest te demonteren e.d. ? toevallig laatst een glock19x gekocht (2e hands) maar is erg smerig met zand e.d. dus wil graag eerst alles eruit hebben voordat ik ga schoonmaken :)
Hi @airsoftNLD, thanks for helping me out to learn how to clean my Umarex 19x. May I ask, by turning the spring during removal and installation, do you find it alters the hop up settings? will I have to pay attention to the orientation of the spring when I put it back to avoid having to set the HopUp again? Thanks in advance!
Great video, thanks! I have a question, when I load mine the bb keeps rolling out of the barrel, is that normal? Do you have an idea what could be the issue?
idk about the steel bb versions they are not legal here but most of them should just work like i show in the video. real life glocks you have to pull trigger then u can get the slide off with airsoft its the other way around hammer must be reset
This might be a stupid question but I'm a total noob. I just got this gun for my birthday, and I adjusted the hop up but couldn't figure out how to take the little tool out could you tell me how to do that?
in like mid of the video the guy took out the little slide piece idk how it fall out on my gun but can someone tell me if its important or not and can i replace it with something
I noticed that if I pull the trigger once more after the slide is back, it won't fully return to it's normal position. How do I solve this? The gun is new, just got it
When I try to take the slide off I do everything you do, but the slide will only move about an inch forward and then it will not move forwards, only backwards to make the slide normal again. Do you know why this is happening or how I can fix it?
I haven’t yet tested the gun to see if it can fire since I just bought it and I’m all out of green gas (waiting for it to arrive) and I’m scared something may be wrong with it
Same here, I’m not trying break mine. Would you be able to make a video showing the internal function of the side buttons to get a better understanding?
UPDATE: Just use a little force by pushing with your thumb on the back of the slide while holding the side buttons down. I guess I’m just used to cheaper airsoft guns. Comes off easier the more you take it apart I feel like.
I stretched that nozzle return spring ever so slightly.. trying to take it off to clean that one part. I ordered another spring.. I find it so hard to remove it neatly, any tips on putting a new spring on? Thanks
@@Enitify It ended up being too damaged to reuse, I went ahead and purchased 3 more off a site and I paid way over price, but needed the replacement. Worth it. Just type, nozzle return spring for that specific gun and you’ll be set. But if you just trying to put it back on, just be careful hooking it slightly pull you won’t ruin it.
Has anyone run into an issue where the gun jams after 2 or three shots? I’m pretty sure it’s a mag issue. I can use another mag and it doesn’t do it. Also this just started, and it’s only the one mag that does it.
@@AirsoftNLD yes have good if looking only but if use not have good chinese shit worst material alltime broken and i have 3 pistol and rifle and newer ewery not has good alltime broken need orden spare parts and come expensive than good tokyio maryui or hi-capa gun. or WE gun. lot lot better gund, i has buy after umarex chinese shit only good guality japanese or taiwanese factory guns, if WE glock cost 4000 B umartex same glock cost 2000 B and umarex can use 2 month and WE glock can use all life end. little bit different guality and material have. but if have 5000-7000B hi.capa or tokiyo marui guns can use all life and newer not have problems. money talk what have good and what have worst. 2000B double bell has super worst normal target shooting go broken less than 1 month. and 3 time orden new spare parts but last time i not orden more i figt this worst shit to trash. double bell and umarex have totally worst material and guality.
The back of my gun was so dry compared to the front 😭 thanks man it was a Christmas present and the slide wouldn’t reset all the way after firing a round I’m guessing it just was not lubricated enough
Very new to the airsoft, my son recieved the redwolf glock19x for Christmas like the one in this maintenance tutorial, and worked great for 2 days and now will only shoot 4 times and it will be out of gas "greengas" and ideas
@@gloomy28 same problem here....doing my head in. I've watched loads of these vids where the slide just comes off. I can feel mine disengage and it's like its working but then sticks on something internally as the slide is about an inch past the front of the lower. Why?????? I've got a TM Glock that comes apart easy using same technique?
Actually...hold the front page...I think I solved it, not sure why this is necessary when clearly it's not in the above video. Follow the steps in the video, then after you release the slide catch and it pops forward, at the point where it sticks, pull the trigger and continue sliding. It should come straight off...mine did, tried it 3 times and it worked every time!
This airsoft pistol is a piece of perfection! 😍
yeah
The damn slide on mine won’t even come off
I heard others with same issue i cant complain i never have trouble getting it off be sure rack slide first then try to get it off or slide lock it then hold pins down and release slide release :)
@@AirsoftNLD believe me, I’ve tried everything. It gets stuck just at the start of the rails it runs along, after the hammer. Once it gets there, I have to pull the trigger at the same time as pushing the slide forward with force. Which is really something I don’t want to do because then I have to reset the trigger by hand by pressing down on the levers which can’t be good.
Hammer broken? Not wanna reset?
I don’t know if I’m doing something wrong but when I do it the same way my Glock slide will go only a inch forward then it’s locked In place and won’t unlike in the video?
I have the same glock as the video i think but the two pins that you pull down when taking off the slide, my pins dont move at all and i put force on em. I also heard in a video they are just for show? but then how do i take off the slide
half blow back model is different than full blowback model
I think for the half blowback you have to take out the 3 pins to remove the slide but I’m not 100% sure
I haven’t tried but it looks like you need to unscrew the rod in the front below the barrel
The same as me. I could not clean the gun. 😢
Great and clear tutorial. You deserve a million views for this.
thank you so much for this. My Glock was jamming every shot before now it works perfectly!!
Is it silicon spray you are using to lube the parts? Sorry if its bad english😅 you are teaching in a way that i understand what you are doing. An how many times in a month do i have to clean it?
I used gun oil to oil this same model… thanks for helping me not screw up my gun.
It's always a good day when AirsoftNLD says "Alright!" in the intro 😭🤘⚡
Great video bro!
Alright, Lolz haha thx
Thanks I shoved the wrong Alan wrench down the hop up lmfao this helped a lot
Hey man, thanks alot! You immediately notice an icreased smoothness.
I use it everyday and repetitively reload the mag, pull the slide and blank fire. Like a toy to figet with if that helps to give you an idea. How often would you recommend cleaning in my case?
What oils/lubricants go on what parts? I plan on getting a maintenance kit from Nostveritch and was wondering if I should just use silicon grease on all the moving parts. I don’t wanna mess up anything.
May I know how to put the recoil spring back together? The parts came apart...thanks...
Hey I've had mine for over a year and have never been able to use it because it won't shoot.. I load everything but when I pull the trigger; nothing..at times BBs dow just roll out of the barrel as well.. do you have any suggestions?
Use gas and adjust hopup
Hey so I just got this airgun. Sometimes when I shoot the bb doesn't come out and then I pull the trigger next and it shoots 2 bbs. Also sometimes when I notice it didn't shoot the BB will just be loose inside of the gun, I will then pull out the mag and the bb will fall to the ground.What am I doing wrong or is my gun defective? I just got some gun oil to put on the CO2 cartridges to see if that is the issue. Is my magazine defective?
Idk man try some oil for the pistol maybe diffrent gas or adjust the hop up. Had issue where bb fell out idk try it
Love the video. I have a question my 19x is not feeding my BBs and the side stays back after the first shot. If I want to slide to move forward, I have to push it from the back of the slide. The funny part is if I have no babies in the magazine and dry fire, it works fine.
I hope that you or someone who knows the answere is answering me 😅
So 1. that one black screw that holds the nozzle unit down and also the rear sight and that black plastic thing in the back. This one screw gets loose every time I shoot or just load the gun a few times. What do I do about it? EverOne seems to have no problems with that except me... and I’m trying to use lock tight right now and hope it helps. And 2. does it damage the hammer if I dry fire it? No gas, no mag or at least mag with no gas and bbs In it. Because I did it a lot and I think I took it to far... the triangular bearing on the hammer scratched of a bit of metal in the hammer housing and also bent the part where it sits in a bit. So does it come from me dry firing it without gas? Or am I just unlucky cus the screw that holds the spring to pull back the nozzle also just went loose and got fired out with one shot and the gun is still just a few days old but that’s not really my fault cus I didn’t do anything, never even took it apart before that happened...what am I doing wrong 😑???
P.S: does it damage the hop up unit if I accidentally double feed the gun (one round chambered in and reload again)?
lol idk about the screw i dont have that. that lock tight might be a solution. or maybe send it back lol.
theres diffrent opinions on dry fire. i dont like to do it. some say it damages your pistol some dont. so i just dont do it.
double feed should not be a problem i do that loads of times lol. maybe u can send it back for repair if its really that bad.
How îs holding up any parts broke? How many shots you put into it?
Nothing broken
*One way to take the orange tip off* take the barrel out of the gun, boil up some water, then stick the barrel in the boiling water. Let it simmer in the water till you think it’s good (this heats up the glue and softens it up) take a pair of pliers or channellocks then pry it off.
This is only if you can’t take the orange tip off from RUclips videos you see. This is one way
I need help fixing my slide. I shot mine a couple times and the slide got stuck backwards and won't go forward, plz help
on the magasine, do you put some silicone grease or silicone oil ?
In the 1:30 what screw was there? I lost it
Is paint wear on the barrel after about 1500-2000 bb's normal?
What did you do to take the orange tip off?
I Never removed something that wasnt on the gun. We dont need them
Hey bro, should I get 19X or 17Gen5? Got a dilemma here. (keep in mind I have TM 17Gen3 and 18C)
Lol idk both? I like them both so idk
AirsoftNLD dude i have budget unlike you hahahaha, so wht do u like from the 17 and from 19x?
My man they both glocks all airsoft umarex glocks are the same only diffrent jacket. All on you. If u like the 19x then take that. I like them both. But i rather have gen 5 glock. Bigger in size.
@@AirsoftNLD ahh really? i just know that now, getting the 19x then. haha thx man
Eerst en vooral een leerrijke vlog 👌.
Ikzelf heb 4 glock's :
- 1 glock 17 gen3
- 1 glock 17 gen4
- 1 glock 17 gen5.
En ook nog 1 glock 19X coyote.
Ik moet kiezen welke ik hou,de gen4 of de gen5 ? Comments en antwoorden zijn welkom. 👋
I think I commented on one of your videos before, I recently got a glock 17 gen 5, and I'm looking to get either a GLOCK 19X (6mm) or a GLOCK 45, which one seems more reliable too you?
How do you remove the inner barrel from the outter? I’ve spent an hour trying but it’s so weird how it catches at every corner
I made video about it
@@AirsoftNLD what video is it?
Great video thanks! Airsoft first time user here. Can you recommend a durable speed loader that is easy to use?
Thx man i dont use speedloaders i got those free ones that sometimes comes with a gun they work fine for me
My top slide release catches don't move. At all. Either side. Any ideas?
Hey brother how did you get the orange tip off? Appreciate the reply
Not america isnt the only country in the world you know :p no orange tips needed here
@@AirsoftNLD who here is American? What kinda stereotype lol. A better answer would’ve been oh it’s a threaded barrel!
@@AirsoftNLD America isn’t the only country that requires a orange tip ya know :P
Or my country doesn’t require an orange tip 😂
I bought the Co2 version and the slide release will not move and I can’t remove the slide. I called service and they say it is NOT supposed to come apart. I have the gen 5 version bought Oct 2021.
Half blowback version.
Anyone have any suggestions?
Lock slide back hold both pins down release slide it will get stuff less than half way so just pull trigger when it gets stuck then it will easily slide right off
Stuck* not stuff lol
Sorry for such late response
@@infamoussnake4042 I have the same pistol with the same problem. What he is saying is that the takedown pins don't move at all. It seems that umarex has made this pistol now ment to be taken down at all as even the hop up adjustment would get in the way of the slide moving forward and would need to be taken out. Would have been nice I'd that was made clear in any of the videos receiving the pistol online
Ignore comment on hop up adjustment was incorrect
my half blowback slide doesn’t come off like that… the 2 “buttons” dont move
Well this isnt half blow back is it :p
@@AirsoftNLD i know, just saying that on hbb it doesn't work like that, wish it could tho
Hello the plastic peice next to the outer barrel chamber thing is loose it's not coming out but it's very lose the more I shoot it the looser it gets how to fix it?
I have the same pistol gen 5 but I can’t get my slide off can’t move the little locks at all any tips?
Great tutorial was the only video I could see the sight removed as I wondered if you can get a custom red dot
Dont know to be fair there prop special plates out there u can put on
Where do you get all the maintenance stuff?
Hey my inner barrel is a bit loose I can move it with pliers. Is that normal? My outter is very lose but I think it’s been like that from the beginning
Tried taking the slide off the way you did and it got stuck. Now the barrel is stuck and won't let the slide go back all the way and I cant take it apart. Any ideas?
no idea just need some force maybe? i always lock slide back pull the 2 pins down and release slide.
@@AirsoftNLD I figured it out a while ago, just needed to pull the trigger and give it some force lol
Very helpful and one of the few disassembly videos for the 19x. Any lower frame disassembly videos out there? For the life of me cannot find a single set of instructions or a video for this model. Thanks!
lower is just to hard with the hammer. i always mess it up. so i suggest u dont remove the hammer just remove oil and such ;D
How often should i clean it
Hey I was wondering have you ever came across an upgrade for the Hop Up ? I'm trying to make this a bit better of a pistol for outdoor to get more distance on my shots.
Maple Leaf products.
@@BenelliMF ya I figured that was kinda hoping theyd give a reference of maybe one they've installed that seem to work..
How often I need to clean my gun?
question: why does my 17 gen 4's outer barrel moves back and forth and creates rattle? when slide open.
Idk all has it
My 19 gen4 does the same, just got it and done the first shoot test, its a lil dissapointing
I'm maybe late but it's designed that way since the real glock barrel tips up to load the next bullet more easily but I think most of the handguns has it. Although it won't affect your aiming since the inner barrel won't move
@@razvan19010 because have chinese shit gun, cheapen gun what have and worst material and not made good.
Do I can put a real 19x slide on that BB gun? That frame looks solid to me
heb je ook een video van de rest te demonteren e.d. ?
toevallig laatst een glock19x gekocht (2e hands) maar is erg smerig met zand e.d.
dus wil graag eerst alles eruit hebben voordat ik ga schoonmaken :)
Hi @airsoftNLD, thanks for helping me out to learn how to clean my Umarex 19x. May I ask, by turning the spring during removal and installation, do you find it alters the hop up settings? will I have to pay attention to the orientation of the spring when I put it back to avoid having to set the HopUp again? Thanks in advance!
i never mess with hopup settings to be fair bc i shoot close range. so i cant answer that.
Why cleaning material did you use for this video?
Nuprol kit
is there anywhere that sells glock gen 5 rebuild kits? My nozzel assembly doesnt have the pin on it for the spring
I tried removing the slide but it only slides forward 1 inch and won't come off.
need some force somtimes. i always rack slide back lock it pull the 2 take down pins down and release slide.
Great video, thanks!
I have a question, when I load mine the bb keeps rolling out of the barrel, is that normal? Do you have an idea what could be the issue?
Change the hopup mine does same thing just play around with hopup and its gone
@@AirsoftNLD thanks, i will try that
Hey, great video. How do I take the slide stop/release and is there any extended slide stops that I can get??
i never done that so i cant really say man
my slide gets stuck in the position you get when pull the side pieces down and then hit the slide release. it wont come off the receiver tho
I have an issue with mine i shoot once and it gets stuck halfway after the first shot then don’t wanna shoot after that
Maybe use other gas. Or oil it up
since u remove the orange tip do the barrel have threads in it to screw on a tracer unit and how did u remove the tip
Never removed orange tips
What type of grease or oils do you use to lubricate it?
Nuprol
When I was cleaning it the spring for the gas thing in the back the slide extended how do I get it back
I have the steel bb version and this doesn't work. I cant pull down the notches
idk about the steel bb versions they are not legal here but most of them should just work like i show in the video. real life glocks you have to pull trigger then u can get the slide off with airsoft its the other way around hammer must be reset
what lubrate product did you use
Could you replace the trigger spring with a glock 8lb trigger spring?
What grease did you use?
This might be a stupid question but I'm a total noob. I just got this gun for my birthday, and I adjusted the hop up but couldn't figure out how to take the little tool out could you tell me how to do that?
I have no idea what you mean with little tool sry lol
@@AirsoftNLD That's alright thanks for replying. lol
I think they ae talking about the small alan wrench
@@VG278Q Yeah. Thanks that's what I was talking about I got it out. Thanks!
my slide is messed up,the triggers mushy and idk why, i cant take off the slide
in like mid of the video the guy took out the little slide piece idk how it fall out on my gun but can someone tell me if its important or not and can i replace it with something
Dry firing GBB's wont cause more or less wear and tear than firing with a BB =) other then that good video dude!
Thanks
Can you take the slide plate of Glock 18c ???
ofc
I noticed that if I pull the trigger once more after the slide is back, it won't fully return to it's normal position. How do I solve this? The gun is new, just got it
Itsnormal
how did you remove the orange muzzle tip
When I try to take the slide off I do everything you do,
but the slide will only move about an inch forward and then it will not move forwards,
only backwards to make the slide normal again.
Do you know why this is happening or how I can fix it?
I haven’t yet tested the gun to see if it can fire since I just bought it and I’m all out of green gas (waiting for it to arrive) and I’m scared something may be wrong with it
The two side button won’t even go down so I can take the slide off 🤦🏻♂️🤷🏻♂️
Should work no issues here they do wanna go in sometimes
Same here, I’m not trying break mine. Would you be able to make a video showing the internal function of the side buttons to get a better understanding?
UPDATE: Just use a little force by pushing with your thumb on the back of the slide while holding the side buttons down. I guess I’m just used to cheaper airsoft guns. Comes off easier the more you take it apart I feel like.
What lube did do you recommend for the Glock 19x
The one i use
@@AirsoftNLD which one do you ide
@@AirsoftNLD use
The one in the video lol nuprol
How did you get the orange tip off
Never did
Metal vs metal = greas
Metal vs other material = oil
Oil = Oil doesnt matter to me.
@@AirsoftNLD LoL
@@AirsoftNLD 😂
I stretched that nozzle return spring ever so slightly.. trying to take it off to clean that one part. I ordered another spring.. I find it so hard to remove it neatly, any tips on putting a new spring on? Thanks
1 year later and I'm assuming you put yours on? how'd you put it on without ruining it?
@@Enitify It ended up being too damaged to reuse, I went ahead and purchased 3 more off a site and I paid way over price, but needed the replacement. Worth it. Just type, nozzle return spring for that specific gun and you’ll be set. But if you just trying to put it back on, just be careful hooking it slightly pull you won’t ruin it.
i have one but it wont work for mines
does this work for all types?
Has anyone run into an issue where the gun jams after 2 or three shots? I’m pretty sure it’s a mag issue. I can use another mag and it doesn’t do it. Also this just started, and it’s only the one mag that does it.
I know I’m late but is it the same for the co2 half blow-back
No idea i dont own one
Jayden did you ever figure out how to take it apart?
My hammer assembly broke and I ordered a replacement. Now I’m sitting here taking way too long trying to put the hammer assembly back together 🤣
Had same issue lol but i got it to work again goodluck
dont buy chinese shit umarex guns have lto easy life buy other korean or japanese brand gund. chinese not can made any good
Umarex is good
@@AirsoftNLD yes have good if looking only but if use not have good chinese shit worst material alltime broken and i have 3 pistol and rifle and newer ewery not has good alltime broken need orden spare parts and come expensive than good tokyio maryui or hi-capa gun. or WE gun. lot lot better gund, i has buy after umarex chinese shit only good guality japanese or taiwanese factory guns, if WE glock cost 4000 B umartex same glock cost 2000 B and umarex can use 2 month and WE glock can use all life end. little bit different guality and material have. but if have 5000-7000B hi.capa or tokiyo marui guns can use all life and newer not have problems. money talk what have good and what have worst. 2000B double bell has super worst normal target shooting go broken less than 1 month. and 3 time orden new spare parts but last time i not orden more i figt this worst shit to trash. double bell and umarex have totally worst material and guality.
something is definitely wrong with my glock. when I try to take It apart it gets stuck on something
Maybe hammer wont reset?
what do you recommend for the oil/lube
What im using in video nuprol
thanksss this video help me so much
Welcome :)
On my glock 19 i broke the part on 3:05 but i have no idea whats it called.
the back plate?
What does dry fire mean im new in airspft
Dry fire in an airsoft gun is when you are out of rounds and still shoot,shooting nothing but green gas
what is your cleaning kit?
Nuprol
@@AirsoftNLD thank you
Is this the green gas version cause I cannot do it on mines
I only own gas pistols
How did you manage to remove the orange tip I'm having trouble taking it off
I did not. They dont come with orange tips. Only in america they come lol
@@AirsoftNLD dammmn thats crazy fuck American laws
Maybe place barrel in hot water might soften the glue who knows
You can buy a threaded black metal barrel for it on evike.com
I can’t for the life of me take the barrel off I slide down the little things and it looks like it gonna come off but it doesn’t slide off any tips
what?
The back of my gun was so dry compared to the front 😭 thanks man it was a Christmas present and the slide wouldn’t reset all the way after firing a round I’m guessing it just was not lubricated enough
And same thing with slide release it would get stuck halfway instead of resetting
You would have to physically push the slide forward after slide release
Very new to the airsoft, my son recieved the redwolf glock19x for Christmas like the one in this maintenance tutorial, and worked great for 2 days and now will only shoot 4 times and it will be out of gas "greengas" and ideas
Sounds like it's not sealing up correctly, leaking green gas out. I have no experience with that particular 19x, but most likely that's the issue
Sounds like it's not sealing up correctly, leaking green gas out. I have no experience with that particular 19x, but most likely that's the issue
Sounds like it's not sealing up correctly, leaking green gas out. I have no experience with that particular 19x, but most likely that's the issue
Sounds like it's not sealing up correctly, leaking green gas out. I have no experience with that particular 19x, but most likely that's the issue
Sounds like it's not sealing up correctly, leaking green gas out. I have no experience with that particular 19x, but most likely that's the issue
I lost the thing where you tighten it to pierce the C02 cartidge does anyone know where i can get another one?
I mean u can just buy tools right
@@AirsoftNLD i went to the website and they had nothing to help me with the problem had to go to the store and swap them out
Do you have a video to disassemble the frame?
Yes ruclips.net/video/llb53N2Lzgo/видео.html
i have the co2 version blowback can i fit on the green gas mag ?
Not sure u gotta test lol
How do you remove the slide so easily?! I have the exact same gun and just can’t remove it.
Lock the slide backward push the 2 pins down and release slide.
@@AirsoftNLD i have the same problem and i did what you said, but it still won’t slide all the way out to remove it. Its weird.
@@gloomy28 same problem here....doing my head in. I've watched loads of these vids where the slide just comes off. I can feel mine disengage and it's like its working but then sticks on something internally as the slide is about an inch past the front of the lower. Why?????? I've got a TM Glock that comes apart easy using same technique?
Actually...hold the front page...I think I solved it, not sure why this is necessary when clearly it's not in the above video. Follow the steps in the video, then after you release the slide catch and it pops forward, at the point where it sticks, pull the trigger and continue sliding. It should come straight off...mine did, tried it 3 times and it worked every time!
@@Cruser1068 do that first, then use your mag to hammer the slide untill it comes off
This video is amazing thank you very straight forward
E limpiado la mia ya dos veces, pero no veo q la goma del hop up salga. Held please.
no idea what this says
I cant seem to get the rear sight out i think its glued on if so how can i take it off?
Yes
Glue i think
Yeah it looks like i just gotta show it some love with a hammer
If u dont see a screw at the bottom inside of slide then yes not sure why u removing it? Upgrade?
I want to get an RMR on there
Can the 19x cO2 version take the plastic bbs as well or no
This isnt co2 so i cant help you there.
Is the 19x's hammer easy to break?😔
idk mine never broke at this day
can you do the same thing but on the Umarex Glock 19X with the co2 can on the mag
Same tutorial just lune all o rings
Wdym “lune all o rings”
I Love the gun and ion want it to get messed up
How did you take off the orange tip?
I did not
What oil do u use?
the one i use in the video lol nuprol pack