Hi buddy. You’re welcome. Glad it helps. I like this esc..the default governor gain work well for certain motor but my 550-700 requires adjustment (increase gain) to meet my preference☺️
Wish they would make a 200A the ZTW Hb heli lineup goes 130A -> 160A ->300A with the 160A $169 and the 200A 500$ that's a huge jump they need something in between.
Great review. I have the 65A version, would you perhaps know how to connect the ESC telemetry (not using Futaba/Sbus), is this using the separate yellow wire to a RX UART? I have this setup through Rotorflight and the Matek G474-Heli. Telemetry appears to be working but there is no current telemetry.
I have very limited knowledge on this. Even with futaba sbus, the changes for the current can only be ‘noticeable’ during flight, not on the ground. Do yours make any changes if spool with 0 load?
Hey Zack . Hope all is well . So I picked up the ZTW skyhawk 125A for the goblin 380 . So there’s 2 sets of wire RBW . For the throttle and send power to the receiver. And the other set RYB wire where would they go to the governor port on the ikon2 .
Oh yeah!!! 65A with trex450 is a killer, u will love it, especially the default value for governor. Fly like there is no tomorrow man! Now, since u got yourself an IZ, u will get full access on the telemetry features! Am happy for you bud😀🔥
@@bardspii2u thank you . IZ will here Thursday . Can’t wait . Now I’ll have to order the ZTW . BTW I was watching some of your videos of you flying . That is crazy stuff . I scale fly . It’s less stressful lol .
@@stevealoia thanks for your comment and support. Im trying to give more exposure on cheaper alternatives in which not really ‘acceptable’ in rc heli scene. Some are just fanboys and hard to be really open on options. I love this hobby and i dont mind sharing good infos to others.
Hey Zack . Received my ZTW 65amp Skyhawks today . Set it up . I can’t get the telemetry to work on the 16IZ . From the ZTW esc to the receive . The yellow wire do I plug that into the Sbus port thank
@@stevealoia okay, what u will need to do, that rx has 4 modes. U will need to change the default mode 1, to mode 2 to enable SBUS2. Starting by pressing the Link/Mode button and power up. Hold it for a few sec and release the button, you will see red led blink once and alternate. Change the mode by pressing it one time, and now it will blink 2 times which indicates your rx is in mode 2 (SBUS2 enabled). To save it, press the link/mode button and hold for a few seconds. Once done, unplug your main power pack. Now, the telemetry line (single wire) should be connected to SBUS2, signal pin. Your esc wire should be connected to channel 3. (Throttle) There you go. On your tx, Go to Linkage > Sensor, see if it detect any reading.
Hey Zack . How do I keep my telemetry when I have the ikon2 FBL in the sbus 2 port . I’ll put the single yellow wire in the ikon on #5 of the 4,5,6 plug of the ikon . Thanks hope all is well
Wow, Zack thanks so much, for this presentation and looks like it's a very reliable esc with affordable price! Cheers mate 👍 👌
Hi buddy. You’re welcome. Glad it helps. I like this esc..the default governor gain work well for certain motor but my 550-700 requires adjustment (increase gain) to meet my preference☺️
Wow, full collection!
baru 3 saja yg sudah d test..65A, 125A dan 160A. ;)
Will it have vbar telemetry in the future?
@@maksymilianwilkus1592 hope they can work together.
Wish they would make a 200A the ZTW Hb heli lineup goes 130A -> 160A ->300A with the 160A $169 and the 200A 500$ that's a huge jump they need something in between.
I think they will..latest update, they will release 85A esc🫠
Big Thank you to Zack for helping me get my Esc and Telemetry working with my Futaba 16IZ . Your the best
You are most welcome Steve. Now your heli is good to go..glad i could offer some help. But seeing others enjoying this hobby is a pleasure😀
Tyrique Radial
Great review. I have the 65A version, would you perhaps know how to connect the ESC telemetry (not using Futaba/Sbus), is this using the separate yellow wire to a RX UART? I have this setup through Rotorflight and the Matek G474-Heli. Telemetry appears to be working but there is no current telemetry.
I have very limited knowledge on this. Even with futaba sbus, the changes for the current can only be ‘noticeable’ during flight, not on the ground. Do yours make any changes if spool with 0 load?
Breanne Lodge
Hey Zack . Hope all is well . So I picked up the ZTW skyhawk 125A for the goblin 380 . So there’s 2 sets of wire RBW . For the throttle and send power to the receiver. And the other set RYB wire where would they go to the governor port on the ikon2 .
Hey Zack the ZTW 65amp is good for trex450 helicopter .and I’m so glad I sent the frsky back and went with 16IZ H radio from futaba
Oh yeah!!! 65A with trex450 is a killer, u will love it, especially the default value for governor. Fly like there is no tomorrow man!
Now, since u got yourself an IZ, u will get full access on the telemetry features! Am happy for you bud😀🔥
@@bardspii2u thank you . IZ will here Thursday . Can’t wait . Now I’ll have to order the ZTW . BTW I was watching some of your videos of you flying . That is crazy stuff . I scale fly . It’s less stressful lol .
@@stevealoia thanks for your comment and support. Im trying to give more exposure on cheaper alternatives in which not really ‘acceptable’ in rc heli scene. Some are just fanboys and hard to be really open on options.
I love this hobby and i dont mind sharing good infos to others.
@@bardspii2u hey Zack I got my 16IZ a bit different to setup on my trex 450 . And just ordered the ZTW 65amp with the programmer . Thanks for you help
@@stevealoia im glad if the video can at least offer a little help for you to go through the setup😄
Hello Zack, would you trust the 130A or the 160A ESC in a 700 helicopter???
I would go for 160A. ZTW 130A HV only offer quite limited peak current, about 160A only. Might as well get the 160A instead.
Where could I source this esc
It requires more exposure so people wont feel hesitate to try them..
Emie Vista
Does telemetry work work with FrSky radio?
As far as i know, currently it can work with Futaba, Vbar and Edgetx.
Hey Zack . Received my ZTW 65amp Skyhawks today . Set it up . I can’t get the telemetry to work on the 16IZ . From the ZTW esc to the receive . The yellow wire do I plug that into the
Sbus port thank
May i know what receiver do you use?
@@bardspii2u Hello Sir . I have the futaba
R7108SB receiver. with the 16IZ transmitter. I think I’m doing something wrong.
@@stevealoia okay, what u will need to do, that rx has 4 modes. U will need to change the default mode 1, to mode 2 to enable SBUS2.
Starting by pressing the Link/Mode button and power up. Hold it for a few sec and release the button, you will see red led blink once and alternate. Change the mode by pressing it one time, and now it will blink 2 times which indicates your rx is in mode 2 (SBUS2 enabled). To save it, press the link/mode button and hold for a few seconds. Once done, unplug your main power pack.
Now, the telemetry line (single wire) should be connected to SBUS2, signal pin.
Your esc wire should be connected to channel 3. (Throttle)
There you go. On your tx, Go to Linkage > Sensor, see if it detect any reading.
@@bardspii2u ok I will give that a try . I know I went Dom live feed to SBUS2 I will check it out thank you
@@bardspii2u ok so I tried all that and nothing . The Signal wire or yellow plugs into the pin closest to the Notch on the receiver right .
Hey zack can’t get telemetry to work. Do I have to register the esc to the transmitter. 16iz
Hey Zack . How do I keep my telemetry when I have the ikon2 FBL in the sbus 2 port . I’ll put the single yellow wire in the ikon on #5 of the 4,5,6 plug of the ikon . Thanks hope all is well