It would be a great idea. I watched their training DVD, but it’s so boring that you can't get through more than 15 minutes of it, even though I paid a hefty price for it. But I doubt they'd accept an lady it; the company is still very macho😂
Put atf in a pump bottle, we squirt it on the rail ever morning while running the head both ways, keeps the felt in the head lubed to keep the rail clean (way quicker) The chain we use a industrial chain spray, gets in better and quicker.. Cheers 😊
We put oil in a cheap pull top dish soap bottle. To oil roller chain on a chain apron/floor round baler. 6 chains on the floor and 2 on the apron. So easy! Oiled chain every 2 hours. Most nights baled 8-10 hours. So easy and clean!
suggestion for woodmizer to add a remote grease zert for drive bearing example harvest combines round baler have many zerts very hard to reach so manufacturers place zerts at a easy to access location and add tubing to the bearing
Emerald, they make a 45 degree grease fitting (zirk) that you could install in that location @ 15:22 and @ 16:20 that would allow you to attach your grease gun MUCH easier! It'd make you grease maintenance so much easier!
Print up a maintenance checklist and have it laminated. Hang it in the dollhouse where it’s clearly visible to remind what needs to be done and how often.
A good air compressor and a ball valve with 4’ of 1/4” pipe flattened to create a blow gun cleans the engine and tight gummy areas very well. Be careful you can damage things with this air.
Emerald if you had a narrow opening on the end of your leaf blower you can shift the sawdust and bark further out and your right about the maintenance not to many people do till something breaks
I was going to say also I've seen a guy that put a cable up with a blower and he set it up so you can pull all the sawdust and push it through a pipe to a finish spot to remove quickly. I also use a snow shovel to scoop the sawdusting and put it in a general pile to use a skid steer to scoop. you guys are awesome. I have two daughters 13 and 14 I'm trying to raise them like you are raised. God bless
If it's hardwood then your are well on your way to major health problems. Hardwood dust is known to cause cancer. Softwood with mould will give you sawmillers lung. And western red cedar causes major respiratory disease. Blowing yourself down is the worst thing you can possibly do. I pity that poor dog in the video. On a different note correct maintenance is really important. But over greasing is fatal for ball or roller bearings. If you see grease emerge from the seals it's already knackered. Fine on bushes like on a loader or backhoe or really slow stuff. For clarification. Most electric motors require zero grease for about 5 years. They don't even have a way to add grease. Sadly too many small mills learn on the job. Flying by the seat of their pants. Wood mixer should have been out and fully commissioned the new mill along with giving FREE training for every aspect of operations. In Europe it's a legal requirement. Not a choice.
Go to Harbor Freight and get a Hercules or Bauer workbench blower. Just like a leaf blower but smaller and lighter with a smaller nozzle to get a more focused airflow.
I love mine, and because it's shorter, it's easier to blow off my clothes...especially on my back. Otherwise it's the blow gun on my Garage compressor.
I think those little black plates right above the rail, on the part where the felt is in, is supposed to be almost touching the rail, so it cleans the rail a bit from sawdust buildup
Amazing video here, I helped my ex and her friends dad run there old mill before they sold it to another friend due to getting too old to run it anymore
Equipment maintenance is high on my list of priorities. I used to work for a tree service and operated everything from chainsaws to the John Deere 790D. I looked after the equipment i used as I don't like being stopped during a work day because of mechanical failure. It's a good habit to have. Once you streamline the process it becomes second nature.
I use a backpack blower and use I. use a 2 gallon pump sprayer mixed with half diesel quarter. used motor oil to spray things down after I blow it off at the end of the day and before I start. if you want you can use vegetable oil mixed with alcohol to thin it so it's more organic
That’s what I thought when Emerald was taking the cover off the felt pad that wipes down the bar that the mill travels on. A ratcheting box end wrench would work well too.
Low speed bearings dont need to be greased much , epically as new bearings tend to have dust covers so if you over geese them the grease blows the cover off the bearing and then dust can get in , but certainly high speed bearings should be greased regularly
I use the Dewalt 20volt grease gun. It has a work light as well. I highly recommend it as it speeds up the process and keeps the most of the mess off of your skin.
Maintenance is essential. I hope Wood-Mizer uses sealed bearings and related components because of the dusty environment. Very true about blowing the dust off first. Oil attracts dust. ATF is a good lubricant for outside uses but the smell is strong.
Sawdust and sap can build up and mess your dimensions up. We rarely sawed pine or other tar like sappy logs, but when we did we would saw one hickory log every fifth log to clean the sap off the blade. Happy sawing and keep that thing lathered up!
Had some chain lubing experience riding dirt bikes on sandy and dusty roads, there are "dry" lubricants, Teflon (PTFE) based, they will lubricate but will not be sticky, saw dust will not clog things up. They cost more than ATF, but they last longer and easy to apply, don't have to do it daily. A cheaper, but also good solution is rubbing the chain with a common candle wax, it will lubricate but will stay dry and less sticky, but this is a more of an improvised solution, can't tell how it will behave in your conditions, may accumulate on some cogs or rollers, may get hot and stick.
My mill is much smaller and basic. Maintenace is just as important but less to do. I also cut my own trees and haul them so time is spent doing that. Also , I live in the far north of Ontario ,Canada so with -50° f winters my usable milling time is limited . A T B
I believe that when greasing, you will be able to see the 'new' grease exiting someplace near the grease fitting. That is when it is full. Just no need to add more than that.
You should wax certain flat metal areas for protection. Maybe fluid film on exterior spots that away from sawdust that will get weathered the most. You sure can manually push that machine 😊
I would guess that the head travel distance could be part of maintenance counters inside the control unit, somewhere next to motor hours (or whatever the official term is for that).
It is practical if the worker also be the mechanics. And spars a lot of money for the family. In our old firm, the mechanicers, who came every day from diverse cities, but wanted not to work in our firm. Probably they earned more and could do private things in firm-time. A family firm is a family firm. I worked in a kind of government firm. Everything pay the tax-payer. All the best for your family.
@11:08 You showed us the "fabricy part" that you soaked with Automatic Transmission Fluid. You said the fabric was dirty and full of sawdust. Have you considered washing it in a bath of ATF or perhaps some solvent then soaking it in ATF? I've done that with some types of air cleaners and it seemed to prolong their life.
I would like to see it under some type of roof. Maybe parcel sides where needed. Winter is coming, snow, ice rain is not good. Watch every episode. Southern Oregon.
I'd be using proper chain lubricant on the roller chain and fluid film on the rail the head slides on.better than ATF it's designed more to prevent foaming than as a stay in place lube.
I'm surprised that chain doesn't have a dispenser where it picks up atf, or sprocket bearing grease, on it's own as it passes through. Like many other chain driven machines such as chain saws.
You mentioned a couple times lately about being at the Paul Bunyan show on October 3rd but it actually runs from Friday October 4th thru Sunday October 6th. Thought you might like to know so you can correct that on future videos. Take care all.
@@scottsoper The 3rd is a mistake. Look up the Paul Bunyan show online like I did and you will see on the website it says the dates are from Friday Oct 4th thru Sun Oct 6th.
@@geraldhandy2589 It is a question of what the internet says vs. what Emerald says! I know that the internet says 4-6th. I have been to the Paul Bunyan Show web site a number of times for a number of reasons. However Emerald and Jade will be there on the 3rd, do their thing and be going home on the 4th. Time will tell if I understand what they are doing correctly.
Bonjour à tous superbe vidéo très bien émeralde il faut être pointilleux sur l’entretien c’est des moulins qui coûte très chère il faut les bichonner n’oublie pas de mettre la ceinture de sécurité quand tu roule livrer le bois bonne journée. Kénavo. Bretagne
What ever happened with the breaking saw blade issue? Curious to know if you ever solved the problem or do you just live with it? Having been a machinist in the day I shudder to see all that saw dust and ATF accumulation on rolling and bearing surfaces. You look good in the natural light.
Some kinds of bearings can be over greased because of the seals that hold the grease in. However you are greasing by hand so it is not too likely that you will push to much grease in, Regular is what is needed, not large amounts. Just fill up the bearing.
Thankyou sensi 😂.. 🙏 🤲... get yourself a little oilcan for the auto transfluid with the rag youll get better penetration. Not too much caffeine get some HYDRATION POWDER in WATER BOTTLES TO KEEP YOU GIRLS HYDRATED... my Sawmill isn't a Woodmiser mine is a AUSTRALIAN HARDWOOD MILLS almost built 😂. Thankyou very informative with the added beautiful scenery ❤💜💐
You also need a flapper on your exhaust pipe. If it rains water goes into your exhaust and could hydrolock your engine which could be very costly repair .
Emerald, you should turn the exhaust on the engine sideways. You'll get rain water going down to the engine. That will ruin an engine quickly if you get enough water going down it.
home school all your children. a working sawmill ran by a home schooled lady will eventually wear out . your videos are very , much gold medal material dang it keep sawing and keep loggin drill a well a nd keep on truckin
I did notice you didnt grease or oil your guide arms for your saw lift. Does the one guide rail have a felt pad under it ? There are also track scrapers on that side.
I would buy a battery powered Blower. The Stihl blower will make your hair smell like 2 cycle oil. Plus the exhaust will give you lung damage. The batteries can charge in the control shed. We use silicone spray on rails because it repels dirt and sawdust better than atf and it doesn’t mess up the ground water. So electric blower and silicone spray plus get a battery powered grease gun with a long pigtail. Keep up the great work. If I was selling Mills I would hire both of you for trade shows and fairs. You both work very hard and know your stuff. Definitely try to keep the chemicals off you.
@@scottsoperI would normally agree except she is using that thing 360 degree. The new cordless blowers are perfect for what she is doing. The fire departments are using them to remove smoke and gasses. I would also use a cordless grease gun. Is this Pennsylvania or Poland turn of the century.
Daily maintenance though key to equipment longevity can sure be tedious. Have you got an old cordless drill or drill/driver laying around with some life left in it? It will work great on small nuts so long as there is room. Just chuck the correct socket and go drdrdrdrdrdrdrdr. Mch much easier and most importantly faster than the box wrench I saw used on the ATF applicator/rail wiper felt cover. Was that the idler or perhaps clutch pulley of the blade drive that you greased at the end of the video. Kinda looked like it but wasn't sure. Love the chennel and the point of view it (you) represent.
Not that I know... Could you use a battery operated tool to remove the nuts fast and flip the felt w/atf on it after a while, then replace on schedule?
Don’t hate me Emmy. I know we’ve been through the Veronica Lake long hair and gloves routine before, and that’s your call. Here’s my catch. When you jumped up on the crossmember of the mill holding the blower while it was running. As agile as you are with legs strong enough to cross time zones, holding the blower in one hand, you were off balance when you made the jump. You could tell by the expression on your face in the instant, even you knew that you exceeded the risk envelope. Here’s why. If there was even the slightest amount of condensation or residual lube oil on the beam or on your shoes, you would have lost traction, the blower would have hit your head, then broken a thigh bone like falling off the high beam in gym. Put the blower down before you make the jump. Never climb without three points of contact. Sorry to be a pinhead Em. I get it that you’re an extraordinarily strong kid and risk is something you chug down like your coffee. I appreciate your work too much for something to ground you.
You have a good sense of humor
I bet spending the day with you makes the day better.
As a retired aircraft mechanic, PM (periodic maintenance) saves repairs in the long run. The old "An ounce of prevention is worth a pound of cure".
Woodmizer should hire you to star as a presenter in some of its training/maintenance videos. You would certainly hold everyone's attention.
Great idea.
She could sell sand to a desert...
@@PerspectiveEngineer Saudi Arabia would be interested, for sure.
Wood miser should have done the upgrade from the lt40 to the lt70 for free. They're getting a ton of free advertising on this channel.
It would be a great idea.
I watched their training DVD, but it’s so boring that you can't get through more than 15 minutes of it, even though I paid a hefty price for it. But I doubt they'd accept an lady it; the company is still very macho😂
Put atf in a pump bottle, we squirt it on the rail ever morning while running the head both ways, keeps the felt in the head lubed to keep the rail clean (way quicker)
The chain we use a industrial chain spray, gets in better and quicker..
Cheers 😊
We use a product called “aerokroil” with silicone. Silicone repels dirt and dust better than straight atf.
I like that not having to take the felt out!!
@@scottsoper yes we might take it out every 3-6 months to give it a good clean but that's it..
We put oil in a cheap pull top dish soap bottle. To oil roller chain on a chain apron/floor round baler. 6 chains on the floor and 2 on the apron. So easy! Oiled chain every 2 hours. Most nights baled 8-10 hours. So easy and clean!
Great video and you are a good teacher. Keep things family friendly, if possible, so the home schoolers can teach from your videos.
suggestion for woodmizer to add a remote grease zert for drive bearing
example harvest combines round baler have many zerts very hard to reach so manufacturers place zerts at a easy to access location and add tubing to the bearing
Routine maintenance is the life of any machine. Take care and it will last for many years. Excellent job ladies thank you for sharing.👍♥️♥️
Loved the videos ❤ Have a wonderful day from 🇨🇦☕️📹👍
Slather and blather are technical terms! Good job.
splather is officially a new word at least in my book
Emerald, they make a 45 degree grease fitting (zirk) that you could install in that location @ 15:22 and @ 16:20 that would allow you to attach your grease gun MUCH easier! It'd make you grease maintenance so much easier!
If I may, I recommend installing grease lines for remote greasing in the places where the zerks are hard to reach.
Develop a written checklist and put it on or by the mill so that things are not overlooked.
Print up a maintenance checklist and have it laminated. Hang it in the dollhouse where it’s clearly visible to remind what needs to be done and how often.
A good air compressor and a ball valve with 4’ of 1/4” pipe flattened to create a blow gun cleans the engine and tight gummy areas very well. Be careful you can damage things with this air.
Enjoyed the video. Thanks for sharing
Emerald if you had a narrow opening on the end of your leaf blower you can shift the sawdust and bark further out and your right about the maintenance not to many people do till something breaks
Your witty repartee is what makes these maintenance videos bearable. Keep at it, you are burning it up!
I was thinking about her eyes
I was going to say also I've seen a guy that put a cable up with a blower and he set it up so you can pull all the sawdust and push it through a pipe to a finish spot to remove quickly. I also use a snow shovel to scoop the sawdusting and put it in a general pile to use a skid steer to scoop. you guys are awesome. I have two daughters 13 and 14 I'm trying to raise them like you are raised. God bless
Woodmizer should have a recommendation chart for all lubrication points on your mill.
.. WM recommends oil/clean the guide rail and chain every 25hrs ..!
I’m always messing with wood so I clean my machines and then I use the blower on me to get all the saw dust off. Great Video!
If it's hardwood then your are well on your way to major health problems. Hardwood dust is known to cause cancer. Softwood with mould will give you sawmillers lung. And western red cedar causes major respiratory disease. Blowing yourself down is the worst thing you can possibly do. I pity that poor dog in the video.
On a different note correct maintenance is really important. But over greasing is fatal for ball or roller bearings. If you see grease emerge from the seals it's already knackered. Fine on bushes like on a loader or backhoe or really slow stuff.
For clarification. Most electric motors require zero grease for about 5 years. They don't even have a way to add grease. Sadly too many small mills learn on the job. Flying by the seat of their pants. Wood mixer should have been out and fully commissioned the new mill along with giving FREE training for every aspect of operations. In Europe it's a legal requirement. Not a choice.
OMG Emerald! What more needs to be said. Love this channel!
Go to Harbor Freight and get a Hercules or Bauer workbench blower. Just like a leaf blower but smaller and lighter with a smaller nozzle to get a more focused airflow.
I love mine, and because it's shorter, it's easier to blow off my clothes...especially on my back.
Otherwise it's the blow gun on my Garage compressor.
I appreciate you and thank you for making content.
Great presentation!
Very nice sawmill and very nice of you.
.. what Emerald is calling the drive belt bearing is just a linkage bushing to engage and disengage the belt/blade ...!
Sono sempre bellissimi i tuoi video sei fantastica
Good job🎉
Имею виду ваше творчество и безусловно физический труд
I think those little black plates right above the rail, on the part where the felt is in, is supposed to be almost touching the rail, so it cleans the rail a bit from sawdust buildup
You girls are an incredible amount of knowledge
Amazing video here, I helped my ex and her friends dad run there old mill before they sold it to another friend due to getting too old to run it anymore
Equipment maintenance is high on my list of priorities. I used to work for a tree service and operated everything from chainsaws to the John Deere 790D. I looked after the equipment i used as I don't like being stopped during a work day because of mechanical failure. It's a good habit to have. Once you streamline the process it becomes second nature.
Breaths new life into it.your symbol of protection!
I use a backpack blower and use I. use a 2 gallon pump sprayer mixed with half diesel quarter. used motor oil to spray things down after I blow it off at the end of the day and before I start. if you want you can use vegetable oil mixed with alcohol to thin it so it's more organic
yes grease maintenance important to do and yes overgrease , happy video 's to look at , succes
Need a socket wrench vs regular wrench.
That’s what I thought when Emerald was taking the cover off the felt pad that wipes down the bar that the mill travels on. A ratcheting box end wrench would work well too.
Low speed bearings dont need to be greased much , epically as new bearings tend to have dust covers so if you over geese them the grease blows the cover off the bearing and then dust can get in , but certainly high speed bearings should be greased regularly
Mighty FINE job!!
Great information good videography and goid thumbnail. Thanks ladies
I use the Dewalt 20volt grease gun. It has a work light as well. I highly recommend it as it speeds up the process and keeps the most of the mess off of your skin.
Maintenance is essential. I hope Wood-Mizer uses sealed bearings and related components because of the dusty environment. Very true about blowing the dust off first. Oil attracts dust. ATF is a good lubricant for outside uses but the smell is strong.
Hey y'all.
nice shorts :-) . use a spray bottle to apply the ATF with a rag under the chain, and get a socket wrench and keep nearby to remove bolts.
Emerald: feel so empty inside? 😂 That just made me laugh. So funny 😘
Great T-Shirt
Sawdust and sap can build up and mess your dimensions up. We rarely sawed pine or other tar like sappy logs, but when we did we would saw one hickory log every fifth log to clean the sap off the blade. Happy sawing and keep that thing lathered up!
Ty😊😊😊😊😊
Had some chain lubing experience riding dirt bikes on sandy and dusty roads, there are "dry" lubricants, Teflon (PTFE) based, they will lubricate but will not be sticky, saw dust will not clog things up. They cost more than ATF, but they last longer and easy to apply, don't have to do it daily. A cheaper, but also good solution is rubbing the chain with a common candle wax, it will lubricate but will stay dry and less sticky, but this is a more of an improvised solution, can't tell how it will behave in your conditions, may accumulate on some cogs or rollers, may get hot and stick.
Great video!
My mill is much smaller and basic. Maintenace is just as important but less to do. I also cut my own trees and haul them so time is spent doing that. Also , I live in the far north of Ontario ,Canada so with -50° f winters my usable milling time is limited . A T B
I believe that when greasing, you will be able to see the 'new' grease exiting someplace near the grease fitting. That is when it is full. Just no need to add more than that.
Thanks beautiful ladies.
So, what will you do with the mill this winter?
Mill lumber..... What do you mean ?
@scottsoper probably means if it snows on top of it, since it's no longer under roof.
You should wax certain flat metal areas for protection. Maybe fluid film on exterior spots that away from sawdust that will get weathered the most. You sure can manually push that machine 😊
That's great advice❕🔥🔥💖😀
Always blow off the radiator. A plugged radiator will cause overheating issues.
It's called a wiper keeps the way clean of debris and lines it up
I would guess that the head travel distance could be part of maintenance counters inside the control unit, somewhere next to motor hours (or whatever the official term is for that).
Isn’t there a manual with a maintenance schedule for all the components?
It is practical if the worker also be the mechanics. And spars a lot of money for the family.
In our old firm, the mechanicers, who came every day from diverse cities, but wanted not to work in our firm. Probably they earned more and could do private things in firm-time. A family firm is a family firm. I worked in a kind of government firm. Everything pay the tax-payer.
All the best for your family.
@11:08 You showed us the "fabricy part" that you soaked with Automatic Transmission Fluid. You said the fabric was dirty and full of sawdust. Have you considered washing it in a bath of ATF or perhaps some solvent then soaking it in ATF? I've done that with some types of air cleaners and it seemed to prolong their life.
Nice Cephalic veins.
Use a driver and socket for the ATF lubing the cloth strip maintenance to make it faster.
Have you considered something like a DuPont
Motorcycle Grunge Brush?
I'd need ear plugs and safety glasses when running the blower. Thanks
ATF oil in your video, is that Automatic Transmittion Fluid? I use chain lubrication made especially for chains. It does not attract dirt.
I would recommend "transmission" fluid??
I would like to see it under some type of roof. Maybe parcel sides where needed. Winter is coming, snow, ice rain is not good. Watch every episode. Southern Oregon.
Unfortunately a roof will not likely be happening before winter.
Perhaps "partial" would work better?
dig the vids, idea for the shirt,,,,, sawdust on my mind, diesel in my veins ,,,,, pc out God bless
I'd be using proper chain lubricant on the roller chain and fluid film on the rail the head slides on.better than ATF it's designed more to prevent foaming than as a stay in place lube.
I'm surprised that chain doesn't have a dispenser where it picks up atf, or sprocket bearing grease, on it's own as it passes through. Like many other chain driven machines such as chain saws.
Wow you look amazing 😍
You mentioned a couple times lately about being at the Paul Bunyan show on October 3rd but it actually runs from Friday October 4th thru Sunday October 6th. Thought you might like to know so you can correct that on future videos. Take care all.
Better be there on October the 3rd if you want to see Emerald and Jade!! I am quite sure that is not a mistake.
@@scottsoper The 3rd is a mistake. Look up the Paul Bunyan show online like I did and you will see on the website it says the dates are from Friday Oct 4th thru Sun Oct 6th.
@@geraldhandy2589 It is a question of what the internet says vs. what Emerald says! I know that the internet says 4-6th. I have been to the Paul Bunyan Show web site a number of times for a number of reasons. However Emerald and Jade will be there on the 3rd, do their thing and be going home on the 4th. Time will tell if I understand what they are doing correctly.
@@scottsoper The show will not be open on the 3rd. If they are there then - there will be no public there to meet them.
Like the new hair doo their Emerald.
Bonjour à tous superbe vidéo très bien émeralde il faut être pointilleux sur l’entretien c’est des moulins qui coûte très chère il faut les bichonner n’oublie pas de mettre la ceinture de sécurité quand tu roule livrer le bois bonne journée. Kénavo. Bretagne
Good informational video. Enjoy watching. Stay safe.
Get a Makita drill motor and put a socket in it and you can remove that plate so much quicker.
What ever happened with the breaking saw blade issue? Curious to know if you ever solved the problem or do you just live with it? Having been a machinist in the day I shudder to see all that saw dust and ATF accumulation on rolling and bearing surfaces. You look good in the natural light.
Some kinds of bearings can be over greased because of the seals that hold the grease in. However you are greasing by hand so it is not too likely that you will push to much grease in, Regular is what is needed, not large amounts. Just fill up the bearing.
Instead of ATF, try 'Fluid Film'. Can purchase by the gallon or in spray cans.
Thankyou sensi 😂.. 🙏 🤲... get yourself a little oilcan for the auto transfluid with the rag youll get better penetration. Not too much caffeine get some HYDRATION POWDER in WATER BOTTLES TO KEEP YOU GIRLS HYDRATED... my Sawmill isn't a Woodmiser mine is a AUSTRALIAN HARDWOOD MILLS almost built 😂. Thankyou very informative with the added beautiful scenery ❤💜💐
awesome
Isn’t there a bearing on the left side also? Or is it a sealed bearing? Good job Emerald! ❤🌹
You also need a flapper on your exhaust pipe. If it rains water goes into your exhaust and could hydrolock your engine which could be very costly repair .
They put a can over it
Emerald, you should turn the exhaust on the engine sideways. You'll get rain water going down to the engine. That will ruin an engine quickly if you get enough water going down it.
They put something over it to keep the rain out.
What about the radiator and the oil cooler. Just wondering mike
I always enjoy your videos. Thank you for taking the time to make them.
home school all your children. a working sawmill ran by a home schooled lady will eventually wear out . your videos are very , much gold medal material dang it keep sawing and keep loggin drill a well a nd keep on truckin
I did notice you didnt grease or oil your guide arms for your saw lift. Does the one guide rail have a felt pad under it ? There are also track scrapers on that side.
I would buy a battery powered Blower. The Stihl blower will make your hair smell like 2 cycle oil. Plus the exhaust will give you lung damage. The batteries can charge in the control shed. We use silicone spray on rails because it repels dirt and sawdust better than atf and it doesn’t mess up the ground water. So electric blower and silicone spray plus get a battery powered grease gun with a long pigtail. Keep up the great work. If I was selling Mills I would hire both of you for trade shows and fairs. You both work very hard and know your stuff. Definitely try to keep the chemicals off you.
Gas powered is best in this case I believe. Anyway it is what they have and it works.
@@scottsoperI would normally agree except she is using that thing 360 degree. The new cordless blowers are perfect for what she is doing. The fire departments are using them to remove smoke and gasses. I would also use a cordless grease gun. Is this Pennsylvania or Poland turn of the century.
Wm must have a chart that denotes all the oiling needed emerald ?!
Daily maintenance though key to equipment longevity can sure be tedious. Have you got an old cordless drill or drill/driver laying around with some life left in it? It will work great on small nuts so long as there is room. Just chuck the correct socket and go drdrdrdrdrdrdrdr. Mch much easier and most importantly faster than the box wrench I saw used on the ATF applicator/rail wiper felt cover. Was that the idler or perhaps clutch pulley of the blade drive that you greased at the end of the video. Kinda looked like it but wasn't sure. Love the chennel and the point of view it (you) represent.
Not that I know... Could you use a battery operated tool to remove the nuts fast and flip the felt w/atf on it after a while, then replace on schedule?
need done? is that the new way to say it in PA?
Shouldn't all the routine maintenance be listed in your manual, including the frequencies to do it?
blades break for a couple way your feed is to fast check the tension if it keeps cracking near the weld the blade might not be anealed right
great T-shirt and love the make up!
Don’t hate me Emmy. I know we’ve been through the Veronica Lake long hair and gloves routine before, and that’s your call. Here’s my catch.
When you jumped up on the crossmember of the mill holding the blower while it was running.
As agile as you are with legs strong enough to cross time zones, holding the blower in one hand, you were off balance when you made the jump. You could tell by the expression on your face in the instant, even you knew that you exceeded the risk envelope.
Here’s why. If there was even the slightest amount of condensation or residual lube oil on the beam or on your shoes, you would have lost traction, the blower would have hit your head, then broken a thigh bone like falling off the high beam in gym. Put the blower down before you make the jump. Never climb without three points of contact. Sorry to be a pinhead Em. I get it that you’re an extraordinarily strong kid and risk is something you chug down like your coffee. I appreciate your work too much for something to ground you.
If you do a lot of wrenching - a speed handle is your best friendd
🔥🔥🔥🔥Emerald🔥🔥🔥🔥