The boat will handle 6 s but it needs a smaller prop. If you modify it with cooling upgrades you can run a stock prop or slightly bigger on 6s for 73 + mph but you have to upgrade the cooling system . I love this boat , it’s an absolute rocket ship if set up correctly. Great vid keep them coming !
I forked my cooling tubes for fresh water and added just used aluminum rivets with center punched out for outlets on both sides.get them home depot cheap,tubing stretches on them with zip ties and stays
I don't think it's just quad addiction, it's an R/C addiction. Getting me excited about boats and I don't even have anywhere to enjoy them around me...lol
That seems to be a common occurrence. I own a Traxxas m41 and it's rated for 6s. I was using it at a local pond and the solder came off, it was fairly lame luckily I was able to rescue it using a drone. But yeah these companies keep pumping out vehicles that go fast but don't think about the heating and venting.
Just like with any vehicle...when you go faster either via faster motor or more voltage...you need to change the gear ratio. For boats that means changing the prop. If you don't you'll over heat things. You must have missed this portion of the instructions: "The included electronics are rated for 2S-6S LiPo batteries; however, running the stock propeller nonstop on a 6S battery could overheat your electronics or damage your batteries. If you run the stock propeller on 6S, we recommend using full throttle on straight line passes only. Return passes should be at half throttle to reduce the heat of the electronics. If you want to run 6S nonstop, use optional propellers (PRB282006 or PRB282027)"
JJ, Been checking out some of your vids. Nice work! That extra water pickup won't work where you have it. The back of the hull on a hydro will be off the water due to prop lift at speed. The place for that pickup on a hydro is thru the bottom of the sponson where it rides on the water. Nice weather ain't far away!
I don't know if anyone has touched on this, but no solder joint is coming undone by heat unless that joint is getting 500+ degrees. If it's getting that hot, it's a poor joint. My XT90s on both my boats and X-maxx get warm when running hard. An aside, and you should know this if you're into quadcopters, is more voltage means less amperage, so running hot on 4s makes perfect sense.
@@jjrotogeek that's weird to me that the ESC would get that hot. For now, just an old Aquacraft UL-1 Superior and a V1 Impulse 31, both with HW 120a ESCs, running on 6s in the Impulse, 4s in the UL-1. Now that I look at the video again, I caught a glance of the solder joint and it looks good, so that wasn't the issue.
Agreed. It was the esc. It’s a known issue with that esc. And that was just on 5s! I’m doing s video this week on a couple new boat builds. You’ll dig it. The new outrigger I built and a genesis that’s going to be very custom lol
Yeah, that boat runs hot, regardless of how many cells you use. Horizon told me 180deg is normal operating temps. The only thing I found that helps is switching to a prop that has less pitch. the stock props 1.7 pitch is too much load on the motor.. I'm going to switch out to a 180amp esc and leopard 4074 combo from OSE..
I tried a Octura x442 that was balanced and sharpened. I ordered it for a different boat, but it brought the temps down quite a bit. There’s a guy on here using a ABC 1716 prop hitting over 70mph stock with 6s.
Hi I had the same problem with my UL-19 i forgot to do the full safe calibration wich is very important and it burned my esc so I had to get a new one also the particular esc is quite small fir the boat
Your like me bro I have to upgrade everything even if there’s nothing left to upgrade I will find somert to upgrade 🤣😂 awesome bro links for the parts you upgraded two
Had the same problems with the UL19 and Voracity. Those escs are junk . Voracity overheated even with double cooling. Big boats like that need a decent esc. We ran a TFL pursuit all day flat out with the stock hobbywing 120amp esc and 3660 motor and not a problem. Proboat are slipping with quality.
The pickup at the back of your hull will do exactly nothing... the rear of your hull on that style boat is for air relief and rides above the water surface at speed
Hi I came across your channel and was listening to the issues you had with boat. I have a Pro Boat Recoil 26 I upgraded the prop to a 440 cnc 3/blade that gave me an additional 6mph faster speed. Then I upgraded the stock 60 amp ESC to the dynamite 120 amp. It runs 4s great but as soon as I tried 6s the boat got so hot the ec3 connector to the lipo battery melted off just like what happened to you. So I fixed that and should have taken it as a clear warning not to use anything larger then a 4s lipo, well I didn't I tried it one more time got two laps in and boom fried the motor. So I ordered a dynamite 2300kv 14 pole marine motor should be ready next week, but no more 6s just sticking to 4s it just runs to hot. The boat will max out at 50 mph on 4s I guess I should just be happy with that and call it a day. But I'm like you always trying to make things better and faster. Anyway just wanted to share that with you long story short a 120 amp ESC is not big enough to handle 6s so they should stop telling people it can, so they don't waste money, you know what I mean. Listening to you talk about all that stuff and upgrading your ESC to 150 amp all makes sense to me now so I can stop trying to figure out why my recoil will not run 6s, so thanks now I know sticking to 4s only,
Hey brother!!!! Yeah woth the upgraded esc and dual water pick up, she runs 5s nice and cool. Haven’t tried 6s. Not sure I will. Can barely keep it in the water on 5s. Can u send me the link to the prop your using??? Oddly enough I just sharpened and balanced mine tonight
I got the first 440 cnc 3 blade prop on ebay for 21 dollars, ran the boat at a summer camp for the kids showing off shit like that, gave the Recoil full throttle and it jumped out of the pool breaking the prop. The second one I purchased off of Amazon for $31.00 with free shipping, great prop .You can find it on ebay just type 440 cnc 3 blade rc boat prop it should be in stock, they make it in China like everything else but it came to the house fast works great.
The three blades prop is one of the reasons your running hot though. Lot more torque. I’m running a huge 3 blade prop on my 52” proboat rockstar and it jumps out too. If u want to run 5 or 6s. You’ll have to drop to a two blades prop. Thanks for the info brother. I’ll pick one up and play with it in 4s
JJ, don't forget about "Hose Clamps, " of some sort, with strong incoming water,,,, they may blow off under the water pressure,,,, UNLESS you play on driving Miss;. Daisy...Lol
I put the auto Baylor and my boat that you will 19 like yours and it was steady flooding it with water everybody tells me that's made for gas boats only so I filled it
I'm getting this boat used tom and I have a 200a esc without Bec what do you recommend Bec wise to add to the esc ? And how would I put the Bec to the esc
You should just be able to wire the bec into the battery terminals (esc side) so when u connect power, the beck will also get power then supply to the reciever. Just make sure your bec can handle 6s.
Need biggers water outlets , you not doing nothing bacause the water fluid is the same because is stock in the outlets , 42mm prop 1.4 pitch less and will run nice with the original ESC 120amp that is for S6 and the water pickup is in a bad position doing nothing but nice ideas but theres on OSE some plates for ESC cooling and better water pickups
Hi I read you put the hull pick up in the wrong place?...did you fix it if so where did you move it too?...and do you have any problems over heating on 6s now?
You all probably dont give a damn but does anyone know of a trick to log back into an instagram account?? I was dumb forgot my password. I love any assistance you can give me.
@Elian Anderson Thanks so much for your reply. I found the site thru google and Im waiting for the hacking stuff atm. I see it takes quite some time so I will reply here later with my results.
Sick boat brother but a course its going to be a F^ huge difference look at the size if it compared to the Dynamite - apples to orange my man! Do you have a PB?
You know you could of just installed better connectors in the first place and saved yourself money and time but I get the tinkering aspect. THe xt90 connectors or the 60s are a complete bottleneck for 6s hard charging. try rc proplus x6 connectors. the best. I use them on 14s
I don’t disagree with that. Thanks for the tip brother. Most of what I do now is gas and nitro. Still do a few electrics here and there. Building a sport 40 hydro. I’ll try those connectors u recommend
What was the Fuck Count? Anyone, Anyone? Anyways, just a thought on the hull pickup, if your boat is lifting out of the water, you will get a lack of water draw would you not, or I suppose bubbles. Why not "Y" it off of one of the rudder pickups
Sir, same boat same problems, love your battery mounts, can you link me to the stl file so I can print some? ordering ose esc next already on my second motor. my cooling is very similar to yours and does drop the temps, also found that different battery mfgs make huge difference in temps and top speed. my boat will run near 70 on 6s but only short runs, overheats and derates, also looking at leppard motor after watching your vid. thanks for the show!
Doug DePottey hey brother!!! Yeah upgrade the esc and get a dual pickup rudder and it’s perfect lol. The motors fine so far. I didn’t make any battery 3d print last for this??? What are u referring to
and i have the aussie dual pick up rudder, it is much larger on both dimensions than the ose, my boat will throw water 6 to 8 inches out the side, dropped running temps 30 degrees.
Oh damn. Send me the link to that if you would. I’ll grab that rudder. Mines cooling fine now, but better is better. Here is the tape I use 3M Dual Lock Reclosable Fastener SJ3560 250 Clear, 1 in x 6 Ft www.amazon.com/dp/B00JHKTDMA/ref=cm_sw_r_cp_api_HuD1BbJZ5J6TB shits awesome
@@jjrotogeek its on ebay www.ebay.com/usr/ponti454, rc boat biz, takes a while to get here but i really like it, turns the boat like a meffer, have t reduce steering on control so it doesn't turn to hard, thanks for the link.
That hull pickup isn't going to do you any good. At speed that part of the boat isn't even in the water. These are considered a 3 point boat meaning the boat only rides on 3 points of the water...the 2 forward sponsons and the prop.
I would assume the lack of morals are the parents that aren’t regulating what their children are watching online. In 5 years I don’t think I’ve ever had a kid make a comment or made known to me that they are watching. But thank you for your judgement and projection of righteousness 🖕
JJRotoGeek Tell you what...seeing as how young kids that are getting into rc modeling want to see videos like yours, do you think that what little morals you do have would allow you to put the words “strong language “ in the header? No? Well maybe you have no morals or you care nothing about today’s youth......or both.
JJRotoGeek Thank you. You just proved my point. You care for no one but yourself. I truly wish I could make people like you understand Maybe then people would talk with more warmth to others. Enjoy what the good Lord has given you. For you, it’s all down hill from here. 🙂
Would subscribe but can’t watch in front of grand kids. Coarse Language seems to be forced. Reminds me of when I was I high school. Oh. Well. An otherwise good resource. Best of luck.
The boat will handle 6 s but it needs a smaller prop. If you modify it with cooling upgrades you can run a stock prop or slightly bigger on 6s for 73 + mph but you have to upgrade the cooling system . I love this boat , it’s an absolute rocket ship if set up correctly. Great vid keep them coming !
Completely agree with what u said.
Ya im converting my Miss Vegas over. using this exact system from OSE, Bought sooo much from them over the yrs... they re awesome.
It's better now. Has big battery connections now and runs about 63 box stock on 6s. Same esc stays cool enough if you run around between speed passes
I forked my cooling tubes for fresh water and added just used aluminum rivets with center punched out for outlets on both sides.get them home depot cheap,tubing stretches on them with zip ties and stays
That’s a damn clever idea brother
Dam bro, I'm surrounded by the ocean and I don't have a boat! Crap like this can make a man homeless!! 😢😆... Love ya!!🤘🤘
I don't think it's just quad addiction, it's an R/C addiction. Getting me excited about boats and I don't even have anywhere to enjoy them around me...lol
That seems to be a common occurrence. I own a Traxxas m41 and it's rated for 6s. I was using it at a local pond and the solder came off, it was fairly lame luckily I was able to rescue it using a drone. But yeah these companies keep pumping out vehicles that go fast but don't think about the heating and venting.
Just like with any vehicle...when you go faster either via faster motor or more voltage...you need to change the gear ratio. For boats that means changing the prop. If you don't you'll over heat things. You must have missed this portion of the instructions: "The included electronics are rated for 2S-6S LiPo batteries; however, running the stock propeller nonstop on a 6S battery could overheat your electronics or damage your batteries. If you run the stock propeller on 6S, we recommend using full throttle on straight line passes only. Return passes should be at half throttle to reduce the heat of the electronics. If you want to run 6S nonstop, use optional propellers (PRB282006 or PRB282027)"
Super informative Awsome information cause of this I pulled the trigger video was Awsome but this one comment made me learn more thanks brother
JJ, Been checking out some of your vids. Nice work! That extra water pickup won't work where you have it. The back of the hull on a hydro will be off the water due to prop lift at speed. The place for that pickup on a hydro is thru the bottom of the sponson where it rides on the water. Nice weather ain't far away!
Agreed. Not sure what the hell I was thinking on that lol. I have since moved it. Thanks for catching that brother
Btw, that's some lovely hydro dipping you're doing. Have you done a how-to-video on that?
Yes brother I’ve done a few last summer. If u want to chic chat we can exchange numbers. Shoot me an email at jjrotogeek@patriot-blades.com
Thanks buddy for the help! Your Fuking right ! Because it’s a nice freakin boat ✨🤙✨💙
Yes .i have the same-its a shame with the cooling system ? Total weard !!!! But i have now the see king 200A with the lepard 6Pole ! It goees wild !!!
Damn I bet!
I don't know if anyone has touched on this, but no solder joint is coming undone by heat unless that joint is getting 500+ degrees. If it's getting that hot, it's a poor joint. My XT90s on both my boats and X-maxx get warm when running hard.
An aside, and you should know this if you're into quadcopters, is more voltage means less amperage, so running hot on 4s makes perfect sense.
Agreeed brother. It was the esc. Over heating and heating through. Swapped her out for a bigger one and no issues. What boats ya running?
@@jjrotogeek that's weird to me that the ESC would get that hot.
For now, just an old Aquacraft UL-1 Superior and a V1 Impulse 31, both with HW 120a ESCs, running on 6s in the Impulse, 4s in the UL-1. Now that I look at the video again, I caught a glance of the solder joint and it looks good, so that wasn't the issue.
Agreed. It was the esc. It’s a known issue with that esc. And that was just on 5s! I’m doing s video this week on a couple new boat builds. You’ll dig it. The new outrigger I built and a genesis that’s going to be very custom lol
Awesome! I'm looking forward to it.
Love how you describe how much stock sucks man lol
Keep up the great work and don't change how you do it 👍
I put the same Auto Bailer you have in my boat is flooding up all the time
Yaa it's my fear about these kinds of experiences that makes me hover around the hobby
Bet she'll run cool now. Gonna be spitting out ice cubes. Very Cool
Great job jj looks awesome bro. Still want to build one of these
Thanks brother 🤘🤘
Yeah, that boat runs hot, regardless of how many cells you use. Horizon told me 180deg is normal operating temps. The only thing I found that helps is switching to a prop that has less pitch. the stock props 1.7 pitch is too much load on the motor.. I'm going to switch out to a 180amp esc and leopard 4074 combo from OSE..
Agreed brother. I upgraded the esc and it helped a ton. I’ll swap out the prop next season as well. What prop u going to?
I tried a Octura x442 that was balanced and sharpened. I ordered it for a different boat, but it brought the temps down quite a bit. There’s a guy on here using a ABC 1716 prop hitting over 70mph stock with 6s.
I put the motor and esc from Vorocity in this boat and it did it some justice
love the printed fuel tube holders
Hi I had the same problem with my UL-19 i forgot to do the full safe calibration wich is very important and it burned my esc so I had to get a new one also the particular esc is quite small fir the boat
Your like me bro I have to upgrade everything even if there’s nothing left to upgrade I will find somert to upgrade 🤣😂 awesome bro links for the parts you upgraded two
Had the same problems with the UL19 and Voracity. Those escs are junk . Voracity overheated even with double cooling. Big boats like that need a decent esc. We ran a TFL pursuit all day flat out with the stock hobbywing 120amp esc and 3660 motor and not a problem. Proboat are slipping with quality.
100% agreed on all counts brother
The pickup at the back of your hull will do exactly nothing... the rear of your hull on that style boat is for air relief and rides above the water surface at speed
Hi I came across your channel and was listening to the issues you had with boat. I have a Pro Boat Recoil 26 I upgraded the prop to a 440 cnc 3/blade that gave me an additional 6mph faster speed. Then I upgraded the stock 60 amp ESC to the dynamite 120 amp. It runs 4s great but as soon as I tried 6s the boat got so hot the ec3 connector to the lipo battery melted off just like what happened to you. So I fixed that and should have taken it as a clear warning not to use anything larger then a 4s lipo, well I didn't I tried it one more time got two laps in and boom fried the motor. So I ordered a dynamite 2300kv 14 pole marine motor should be ready next week, but no more 6s just sticking to 4s it just runs to hot. The boat will max out at 50 mph on 4s I guess I should just be happy with that and call it a day. But I'm like you always trying to make things better and faster. Anyway just wanted to share that with you long story short a 120 amp ESC is not big enough to handle 6s so they should stop telling people it can, so they don't waste money, you know what I mean. Listening to you talk about all that stuff and upgrading your ESC to 150 amp all makes sense to me now so I can stop trying to figure out why my recoil will not run 6s, so thanks now I know sticking to 4s only,
Hey brother!!!! Yeah woth the upgraded esc and dual water pick up, she runs 5s nice and cool. Haven’t tried 6s. Not sure I will. Can barely keep it in the water on 5s. Can u send me the link to the prop your using??? Oddly enough I just sharpened and balanced mine tonight
I got the first 440 cnc 3 blade prop on ebay for 21 dollars, ran the boat at a summer camp for the kids showing off shit like that, gave the Recoil full throttle and it jumped out of the pool breaking the prop. The second one I purchased off of Amazon for $31.00 with free shipping, great prop .You can find it on ebay just type 440 cnc 3 blade rc boat prop it should be in stock, they make it in China like everything else but it came to the house fast works great.
The three blades prop is one of the reasons your running hot though. Lot more torque. I’m running a huge 3 blade prop on my 52” proboat rockstar and it jumps out too. If u want to run 5 or 6s. You’ll have to drop to a two blades prop. Thanks for the info brother. I’ll pick one up and play with it in 4s
Great work, JJ! That's a sick boat!!!
Just don't throw away the old esc... Maybe you can use it to make a half size boat for your kid. LOL
JJ, don't forget about "Hose Clamps, " of some sort, with strong incoming water,,,, they may blow off under the water pressure,,,, UNLESS you play on driving Miss;. Daisy...Lol
Lolol. Agreed brother!!!
What batteries do you use and charger
Very nice work brother!!! I subbed👍
What batteries do you use exactly? And charger?
Seen a video where the water outlet was drilled out to 2.5 mm I drilled mine out some he said it ran cooler
I put the auto Baylor and my boat that you will 19 like yours and it was steady flooding it with water everybody tells me that's made for gas boats only so I filled it
I'm getting this boat used tom and I have a 200a esc without Bec what do you recommend Bec wise to add to the esc ? And how would I put the Bec to the esc
You should just be able to wire the bec into the battery terminals (esc side) so when u connect power, the beck will also get power then supply to the reciever. Just make sure your bec can handle 6s.
I got a kick just listening to how many times u cussed in the vid😂
Need biggers water outlets , you not doing nothing bacause the water fluid is the same because is stock in the outlets , 42mm prop 1.4 pitch less and will run nice with the original ESC 120amp that is for S6 and the water pickup is in a bad position doing nothing but nice ideas but theres on OSE some plates for ESC cooling and better water pickups
Hi I read you put the hull pick up in the wrong place?...did you fix it if so where did you move it too?...and do you have any problems over heating on 6s now?
Awesome upgrades brother. i know your not done either. Can't wait to see her run!
You all probably dont give a damn but does anyone know of a trick to log back into an instagram account??
I was dumb forgot my password. I love any assistance you can give me.
@Ryland Brayden instablaster =)
@Elian Anderson Thanks so much for your reply. I found the site thru google and Im waiting for the hacking stuff atm.
I see it takes quite some time so I will reply here later with my results.
@Elian Anderson it worked and I now got access to my account again. I'm so happy!
Thanks so much you saved my ass!
@Ryland Brayden Glad I could help xD
What's up with your next video on the upgrades? I think we'd all like to see video of it shredding!
Agreed!!! Need to get my ass down to the water
You sound like us in jersey fuckin fuckin fuckin love it brother I just subbed fuckin aaaaaaaaaaa lol
Im looking to buy the same boat..
Where do I get these upgrades? I just got one of these for my son
Stock 5s is best temps are good. 6s on off throttle your good.
Agreed 🤘
And when your esc gets burned it dose that exact thing
Great vid. What do you think of the traxxas spartan for my first boat.
From what I’ve heard it’s a great duck
JJRotoGeek okay cool. I may try it out.
Besides the fact the hull is cheap plastic instead of fiberglass
MrJnation89 I went with a oxidean Marie mini dom. I really like the self righting on it.
By any chance do you still have the ESC ? Mine burnt out in my Recoil and I'd buy yours if you would be interested. Let me know!!!
Love to help ya out brother but I don’t 😰
He uses the f word in almost every sentence I like it
Sick boat brother but a course its going to be a F^ huge difference look at the size if it compared to the Dynamite - apples to orange my man! Do you have a PB?
Hey brother, a PB?
@@jjrotogeek your personal best record in speed mate?
You know you could of just installed better connectors in the first place and saved yourself money and time but I get the tinkering aspect. THe xt90 connectors or the 60s are a complete bottleneck for 6s hard charging. try rc proplus x6 connectors. the best. I use them on 14s
I don’t disagree with that. Thanks for the tip brother. Most of what I do now is gas and nitro. Still do a few electrics here and there. Building a sport 40 hydro. I’ll try those connectors u recommend
Great vid. Thinking about getting this boat. How did the upgrades work?
It’s a great hull. They worked great. I strongly advise that unshitcan the original esc and put in a better one. That one is a crapwagon
👍 thanks for the advice
silver solder melts a higher temp never tried it, my pursuit melts the solder leopard motor
Dang bro, I want see that thing rooster.
Nice And i Thought my cooling was cool mine squirts up tho lol
"mine squirts up tho" Most of ours should ;)
How do you replace the plastic piece inside the shaft?
????? Which part brother
The plastic tubbing that keeps the flex shaft from touching the inside of the shaft
Gear drive off of the motor with twin screws!
What was the Fuck Count? Anyone, Anyone? Anyways, just a thought on the hull pickup, if your boat is lifting out of the water, you will get a lack of water draw would you not, or I suppose bubbles. Why not "Y" it off of one of the rudder pickups
Sir, same boat same problems, love your battery mounts, can you link me to the stl file so I can print some? ordering ose esc next already on my second motor. my cooling is very similar to yours and does drop the temps, also found that different battery mfgs make huge difference in temps and top speed. my boat will run near 70 on 6s but only short runs, overheats and derates, also looking at leppard motor after watching your vid. thanks for the show!
Doug DePottey hey brother!!! Yeah upgrade the esc and get a dual pickup rudder and it’s perfect lol. The motors fine so far. I didn’t make any battery 3d print last for this??? What are u referring to
@@jjrotogeek did u 3d print the tape for the batteries or buy it, i HATE those effing straps to hold em down, big pia
and i have the aussie dual pick up rudder, it is much larger on both dimensions than the ose, my boat will throw water 6 to 8 inches out the side, dropped running temps 30 degrees.
Oh damn. Send me the link to that if you would. I’ll grab that rudder. Mines cooling fine now, but better is better. Here is the tape I use 3M Dual Lock Reclosable Fastener SJ3560 250 Clear, 1 in x 6 Ft www.amazon.com/dp/B00JHKTDMA/ref=cm_sw_r_cp_api_HuD1BbJZ5J6TB shits awesome
@@jjrotogeek its on ebay www.ebay.com/usr/ponti454, rc boat biz, takes a while to get here but i really like it, turns the boat like a meffer, have t reduce steering on control so it
doesn't turn to hard, thanks for the link.
That hull pickup isn't going to do you any good. At speed that part of the boat isn't even in the water. These are considered a 3 point boat meaning the boat only rides on 3 points of the water...the 2 forward sponsons and the prop.
You trying to be a hand model or something, lol
Lolol. Hmmmmm maybe I should
This old tony has entered the chat
I run mine on 6s 100% stock lol
ohhh RC Porn
What the hell is with the hand show? lol....pull back on the camera!
Some reason you have to cuss on a video that kids watch? Lack of morals
I would assume the lack of morals are the parents that aren’t regulating what their children are watching online. In 5 years I don’t think I’ve ever had a kid make a comment or made known to me that they are watching. But thank you for your judgement and projection of righteousness 🖕
JJRotoGeek Tell you what...seeing as how young kids that are getting into rc modeling want to see videos like yours, do you think that what little morals you do have would allow you to put the words “strong language “ in the header? No? Well maybe you have no morals or you care nothing about today’s youth......or both.
JJRotoGeek Thank you. You just proved my point. You care for no one but yourself. I truly wish I could make people like you understand Maybe then people would talk with more warmth to others. Enjoy what the good Lord has given you. For you, it’s all down hill from here. 🙂
Lol. Your so trivial and judgmental, I do more for people than u possibly know. But because I curse I’m immoral. Your simple
Amen to op.
Would subscribe but can’t watch in front of grand kids. Coarse Language seems to be forced. Reminds me of when I was I high school. Oh. Well. An otherwise good resource. Best of luck.
I’ll take that crapwagon Esc off your hands.
Sorry brother, I think I already gave it away but I’ll check. I have a ul19?
U
JJRotoGeek I have two blackjack 29’s one is complete the other is just the hull.
Upgrade your language...
Try not to cuss so much