thanks for this proyect, i have a doubt about the audio conection, i don´t know the stereo conection, because no wire is connected to the negative, in the left ic, in the 10k resistor the audio conection is positive oe negative?
the negative terminal of the speaker is connected to the 1st 2030 output pin and the positive terminal to the other 2030. 2 Inputs used in 2 2030 are non inverting inputs.
from the datahseet....... The TDA2030 is a monolithic integrated circuit in Pentawatt® package, intended for use as a low frequency class AB amplifier. Typically it provides 14W output power (d = 0.5%) at 14V/4Ω; .................. double that in a bridge mode so with a 4 Ohm speaker 28W is possible in bridge mode though at moderate distortiion
You seem to have an understanding of the concept. I have a question. Can you find and post here a circuit diagram for me that will power 2 x 100w speakers at 8 ohms and can be driven from a 240v power supply (so a step-down transformer needs including) and the input is RCA cable from a tuner? I need a simple white noise set-up from a simple amplifier circuit with a potentiometer and outlet for 2 100w speakers for my bed. My neighbour is mentally ill and has taken to smashing on her floor/my ceiling at all hours. I need a powerful white noise set-up where I have 2 x 100w speakers (let's say 100w per channel) and I will buy a tuner to plug in to it through RCA cables. I'm so tired and no one will help me resolve her vile conduct. Thanks!
semua yg ada di konten anda saya praktekkan dan yg berhasil saya lakukan yg single tda 2030 sangat bagus..yg stereo double tda hasilnya kurang bersih suaranya..kira2 kenapa ya..? apakah karena kapasitor yg 10uf 63v,, saya ganti 10uf 50v??
depende si le pusiste un potenciometro o no si es si ponele un alambre preferiblemente no descubierto al chasis del potenciometro y conectalo al negativo del potenciometro y ademas si eso falla intenta colocar un capacitor serca a los transistores asi la corriente va a entrar al circuito sin basura externa preferiblemente de 25v100uf-1000uf con eso ademas de usar un cable blindado corto del potenciometro a los transistores ya deberia solucionar el problema 👍
WARNING from the datasheet............... Printed circuit board The layout shown in Fig. 16 should be adopted by the designers. If different layouts are used, the ground points of input 1 and input 2 must be well decoupled from the ground return So this layout here is NOT RECOMMENDED
The ic's output about 15 watts each and from a 12 volts battery you can't output 250 watts you need about 50 or 60 volts Heat sink is very small 😢 You don't have the slightest idea of what you are doing
Como haria para colocarle un pontenciometro y jack para conectarle un bajo electrico, podrias hacer un video haciendo un circuito para eso? bendiciones
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
Verry --- power full,,,,sond sytem❤
Thank you so much ❤️
🎉🎉🎉🎉 muito obrigado pelo vídeo amigo.gostei .
Eu que agradeço ❤️❤️
Superb ❤❤❤
Thanks 🤗
অনেক সুন্দর ইনশাআল্লাহ এগিয়ে যাও ❤❤❤
Its regally great ❤
Thank you so much 💕
Dada aaj eta ami try korlam khub valo bajche bass o darun Dada thanks❤❤❤❤🎉
Thank you so much ❤️
Creatives I ❤ 8..thank you for sharing us.god bless.
Thank you very much for the nice comment❤️
thanks for this proyect, i have a doubt about the audio conection, i don´t know the stereo conection,
because no wire is connected to the negative, in the left ic, in the 10k resistor the audio conection is positive oe negative?
Dear friend this is a functional circuit you can make very easily if you want. thank you.
@@taletech This is a very bad circuit
So grate working
Many many thanks
Como haria para colocarle un jack para conectarle un bajo electrico, podrias hacer un video haciendo un circuito para eso? bendiciones.
Good. This is real video. ❤
Many many thanks
Bhai sound kaisi aati hai laud hai ya nahi batao please
Very humminng soung how can i do away with it kindly
Input pe 4.7uf capacitor laggao audio input aur ground me parallel me aur ground pe capacitor ke plus ke sath 10 ohm ka resistance.
please take a video of how to assemble an amplifier on TDA8588J.
I will try to give it in a few days.
@@taletech ok!
the negative terminal of the speaker is connected to the 1st 2030 output pin and the positive terminal to the other 2030. 2 Inputs used in 2 2030 are non inverting inputs.
What is the wattage of the speaker and AC?
80w
@@taletech WRONG!
Definately wrong
How can I reduce harming sound coz it's very loud
Please use batteries
Can i use a 19v laptop charger on that type of circuit?
Excelente, muito bom.
Thank you
Nice project ❤
Thank you! 😊
Nice Project 😊
Thank you! 😊
220 uf 35v ka capisitor nahi hai koi dura laga sakte hai kya
Yes
Powerful Simple Circuit. Thank you❤
Thank you so much ❤️
Sir how much voltage and ampere do you used?
Bhai mene aapke jesa hi banaye heavy bass hai
Thank you ❤️
Big speaker shown but low in Watts. It's produce max 40W not more
is the 13007 amp better too
Thank you ❤️
Fantastic!
Thank you! Cheers!
220 uF 25 volt Is it suitable?
no problem You can use it. thank you
@@taletech It's not working, I did everything right
Bolchi j dada 470 ohm er bodole 100-300ohm er ki dao jabe
You can try it. Thank you ❤️
Bro can I change 470 ohm resistor to 1k ? or another?
Because I don't have 470 ohm😔
Bro. You can try connecting.
I REALLY question the wire thickness/gauge as this is a high current application
How many watts speaker and how many speakers am supposed to use
Use 60watt
👍show
from the datahseet.......
The TDA2030 is a monolithic integrated circuit in
Pentawatt® package, intended for use as a low
frequency class AB amplifier. Typically it provides
14W output power (d = 0.5%) at 14V/4Ω;
..................
double that in a bridge mode so with a 4 Ohm speaker 28W is possible in bridge mode though at moderate distortiion
You seem to have an understanding of the concept. I have a question.
Can you find and post here a circuit diagram for me that will power 2 x 100w speakers at 8 ohms and can be driven from a 240v power supply (so a step-down transformer needs including) and the input is RCA cable from a tuner?
I need a simple white noise set-up from a simple amplifier circuit with a potentiometer and outlet for 2 100w speakers for my bed. My neighbour is mentally ill and has taken to smashing on her floor/my ceiling at all hours. I need a powerful white noise set-up where I have 2 x 100w speakers (let's say 100w per channel) and I will buy a tuner to plug in to it through RCA cables. I'm so tired and no one will help me resolve her vile conduct.
Thanks!
Сер добрый вечер спасибо за видео 👍👍👍это линейный усилитель микросхемы греются подскажите
the pin 3 is not connected to the ground. That is the negative dc terminal. How come it isnt connected to a negative power supply?
Bro. This is 100% realistic video. You can make it very easily if you want.
Legal
Thank you so much 👍
10uf 50v chale ga kya
❤
Beautiful circuit 👍
Thank you! Cheers!
Nice project
Very easy circuit ❤️ thank you.
You are welcome 😊
Seems this is a BRIDGE version
Pode colocar dois alto faltante
Thank you
Good
Thank you so much ❤️💟
I want to ask a question
tell me
💪💪💪💯❤
bisakah anda membuat yang versi 2050 BTL
ok i will try.
Very distorted sound, even at low volume. Absolutely no bass at all. I’ve double and triple checked every wire, what could be wrong?
semua yg ada di konten anda saya praktekkan dan yg berhasil saya lakukan yg single tda 2030 sangat bagus..yg stereo double tda hasilnya kurang bersih suaranya..kira2 kenapa ya..? apakah karena kapasitor yg 10uf 63v,, saya ganti 10uf 50v??
WARNING
The Thermal resistance junction-case is quite high so you need a BIG heat-sink in high power use. Not the tiny one used here
sember
You may have made a mistake somewhere, please watch the video carefully.
bhai mene bhi banaya lakin mera clear sound nahi da raha
Try again it must be a real video thank you.
put it on breadboard do a tutorial ON BREADBOARD PLEASEEEEEEEEEEEEEEEEEEEEE
I will try bro
@@taletech ty
Cómo quito lá interferencia 🤔
depende si le pusiste un potenciometro o no si es si ponele un alambre preferiblemente no descubierto al chasis del potenciometro y conectalo al negativo del potenciometro y ademas si eso falla intenta colocar un capacitor serca a los transistores asi la corriente va a entrar al circuito sin basura externa preferiblemente de 25v100uf-1000uf con eso ademas de usar un cable blindado corto del potenciometro a los transistores ya deberia solucionar el problema 👍
like the sound is saturated..
Eta ki dc 12 0 supply naki 12 0 12 supply????❤
DC12 0 Supply 👍
What is the maximum watt output
It won't produce 250 w it will produce quatar of it
WARNING from the datasheet...............
Printed circuit board
The layout shown in Fig. 16 should be adopted by
the designers. If different layouts are used, the
ground points of input 1 and input 2 must be well
decoupled from the ground return
So this layout here is NOT RECOMMENDED
❤❤❤❤❤
Thank you ❤️
WARNING from the datasheet...............
the circuit in the datasheet is quite different than here
Vc fãs pra vender
It works but I am getting insane humming sound...
if you foillow a clown you can only expect a clown show
🎉🎉🎉🎉🎉
apakah kapasitor 10uf 6v bisa di ganti dengan ukuran lain
maaf 10uf 63v maksud saya
Yes
Saya praktekan sesuai video, tetapi gagal, apa ada yang tersembunyi dari video ?
Nothing is hidden.
@@taletech tetapi kenapa saya praktek kok tidak keluar suara, cuma suara noise aja ?
@@taletechgimana saya bisa dapatkan diagram sirkuitnya ?
14watt + 14 watt
How much watts output
You can make it if you want. This circuit is heavy powerful.
@@taletech useless reply
The ic's output about 15 watts each and from a 12 volts battery you can't output 250 watts you need about 50 or 60 volts
Heat sink is very small 😢
You don't have the slightest idea of what you are doing
AGREED this is a bad joke
w..????
It doesn't work properly
You may have made a mistake somewhere. Please try again. this is real video. Thanks
Bhai not working it is fake
Bhai work karta hai
Mana bhi banaya hai
Please watch the video carefully. This is a realistic video. You may have made a mistake somewhere. thank you.
Thank you ❤️
Stake Kari hogi bro please retry
why is it Ultra Bass? LMAO
Lol
Yes not working it is fake
Every video in this channel is realistic. We do not upload fake videos.
fake
This is 100% realistic video. You can make it very easily if you want. Thank you.
@@taletech saya gagal dan tidak ada bunyi sama sekali...
my from indonesia
Fake
100% realistic video.
Como haria para colocarle un pontenciometro y jack para conectarle un bajo electrico, podrias hacer un video haciendo un circuito para eso? bendiciones
I will make such a circuit very soon. Thank you dear brother.