Showed all the easy sides of welding in an Boiler try being 4 deep in the superheats welding in a mirror using both hands and the plant wants to x-ray it them
Boiler tubes are definitely not for everyone. A whole different set of welding skills. Super heats are definitely a chore. Just getting in to them is a bitch.
@@kf8575 ok so if you had 1700 hours of tig welding to do then what would be the number 1 thing your paying attention to in order to save time? Can you just keep adding more rod to go faster? Can you turn up the heat and risk destroying the part? Can you turn up the gas to make it better? Your acting as if my comment was terrible and completely out of context when in reality the only thing that could slow him down would be dipping his tungsten and having to resharpen it over and over again right?
@@tylerhensley2312 dont get your panties in a bunch dude, was a joke for crting out loud😄 Sharpen a few up, in a little tube in your boilersuit pocket and your good to go. Anyone that makes out they dont ever dip a tungsten or get a drip of filler wire contamimate it is a bullsh***er. Last thing needed is to have to climb down from an awkward spot to grind up a tungsten
Welding in the pipe rack ain't got shit on y'alls work bro, good job brotha I can only imagine how bad your body aches after being all twisted up inside that spaghetti mess much respect bro
Correct. Started welding in 1976 retired in 2017. Not only is it tough work but the cold steel will take a toll on you. Hip replacement. Bad knees both scooped to remove bone chips. Receive multiple qourtazone shots in back and shoulders. And have macular degeneration. I miss working with the guys but don't miss crawling around in tanks and boilers
To those who want to know welding try by all means to practice right and left hand welding. By so doing you will be broadening your chances of being a preferred welder.
What about the hoods? Just cos theyre not expensive? So in your opinion what should they be using?? Speedglass? Optrel? 99% of auto lenses are absolute dogshit for tig welding with restricted line if sight, let alone when using a mirror.
@@kf8575never had a problem 😂😂😂😂 because I’m not a loser hiding in pipes who will be sitting on bed my entire life when I’m older due to having a busted body.
Boilermakers aren't allowed to weave a cap or any other weld for that matter. Stringers only, you are not supposed to go more than 3x wider than the diameter of your rod. No jack stand walking the cup BS their. Peace
Nitro junkie I never knew pipe got capped this way till recently I always thought it was weaved in for some reason. I’m on my last semester in college welding and I’ve never thought about being a boilmaker looks hard but interesting
@Sean Kean That is correct but under the old certified classification in the Boiler making trade they were termed Pipe welders and most welding registers Lloyds and several others were, and still are registered as Pipe Welders, I think ABS is the exception as you may guess.
@Sean Kean No problem, ABS is the American Bureau of Shipping - US equivalent to Lloyds shipping. I think a lot depends on which country you are in as there are often differences in reference between them, often the US going its own way.
Cost of living very low in poland. Thats why they flood into western europe, pull the racist card and undercut local tradesmen in order to get work, to then pss off home after a couple of years👍
Retired Boilermaker 35yrs, all them non-welding video guys who make welding videos should watch this video, this is why Boilermaking isn't for pipe welding bench welders.
I am doing this in my welding class Corbin was coming out OK but the carbon and stainless filler wire or you have to pump argon in the pipe is difficult Masking tape keep catching on fire
Hello everyone.I watched this video,and that's what I do.Can anyone recommend a company that needs welders?I use it equally with my left and right hand,I also use a mirror....etc.Thank you very much.
No offence but tig welding does get much more difficult than this. These are all fairly open access welds, I am a nuclear tig welder on submarines and almost all of our welds are far more restricted than these ones shown. The welding in this video is skillful but its far from the most demanding Tig welding out there.
Witam. Super robota i mistrzostwo👍👍 Mam również pytanko. Zawsze chciałem taką robote dorwać ale nie zawsze się udawało. Chciałbym się zapytać jakie uprawnienia zrobić na taką robote?? Znaczy się w jakiej grupie materiałowej FM4 czy FM6 bądź też FM5 która z tych?? Oraz czy wy spawając te rurki ,rureczki użtwacie również metody Tig-lift jak to robią w USA lub UK?? Oraz czy robić łączone 141/111 czy każda osobno na rure w pozycji 6G?? Sorki za tyle pytań ale od niedawna się tym interesuje chociaż spawam od 15 lat Tig i Mig z tym że przeważnie nic specjalnego na zakładach nudne powtarzalne elementy😨 Z góry dziękuje za odpowiedź Pozdrawiam
Dobra robota chłopaki👍👍👍💪💪💪 Dziwne że wy spawacie z wolnej a mi kazali kręcić na próbkach, ciekawe. Swoją drogą takie pytanko jakie tam tigi macie 230V czy 400V i jakie marki?? Pytam bo chcę kupić tiga właśnie z przeznaczeniem na takie roboty. Pozdrawiam i tak trzymać👍👍👍
Impresionante enhorabuena mucho nivel es una pena q no haya máscaras para espacios reducidos mejores q esas de cuero , verdaderamente penoso !!felicitaciones os admiro
Wow impressive. I had to do a quick repair during a shutdown week. The re tubing job was a few months away. Not that big of a boiler. Would hammer bulging tubes in. A few blown tubes so close together on the wall had to cut a window in the front. weld the back and sides I couldn’t reach through the window I cut out of the tube then weld the window on the front of the tube. I was a pipe welder not a boiler maker. I have no idea if it was something you should do or not. Just had to get it ready to make steam in a few days. I wouldn’t put my stamp on it. The twin boiler was already down for new tubes no steam the plant would be closed. Held up until they had it re tubed. I was young this was back on the 60’s. To code or not to code?? I had a ASTM stamp as I recall. It got three passes almost half only on the inside.
The welds are very good. The fit up on the tubes in the thumbnail is not good. Some of them have a bad dog leg. The membrane on the new panel should of been split to straighten the tubes up. Most weld techs or even the customers would through and fit over the fit up on the panel.
Walk cup fools!!! China busting it out better and faster. Step it up welds look rolled, undercut, and inconsistent. Remember, it’s TIG it should be looking hell lot better. Looks like you stick weld that
They’re boilermakers 😂 they’re not allowed to walk the cup for some stupid unknown reason because they give the exact same results… stringers just look like shit.
It was, until he ruined it by running a file/grinder around the toes of the cap. That fails QA here in UK on any high spec work, due to removing wall thickness👎
@@kf8575 - Haha... really? That joint isn't being fitted in a nuclear powered submarine for you to claim that it wouldn't pass UK's code of inspection. I'll tell you what, if you were a QA on one of my field construction, conventional boilermaker jobs and, you rejected that weld for your claim of wall thickness removal.... that would've been your last weld inspection on that job.
You learn how to push the limits on just how far you can pull that tungsten out. Lol. And how to feed the wire from the inside. And how to feed wire for your tube partner. Them ain’t pipes BTW, them is tubes , big difference……
@@lonewolftech actually, pipe has a seam, tubes don’t. Also pipe is measured using the inside diameter, boiler tubes are measured using the outside diameter. If you had went through an apprenticeship you’d know that.
Loved all of the free hand. That's a boilermsker's bread and butter
Showed all the easy sides of welding in an Boiler try being 4 deep in the superheats welding in a mirror using both hands and the plant wants to x-ray it them
Yep. Been there.
You must be a hero.
Nope.Id be so pissed I'd have to quit.Fuck that
Where we can find your fantastic videos haw really welding looks like ?
Boiler tubes are definitely not for everyone. A whole different set of welding skills. Super heats are definitely a chore. Just getting in to them is a bitch.
Nice to see,,,,need a Job like this,,,me Tig-Welder,,,
szwecja z mostostalu zabrze?? pozdro
Dokładnie tak. Byłeś???
용신!~~
the biggest and most time saving trick to this kind and amount of welding is to NOT dip the tungsten.
Thanks you mean almost 90 degree of tungsten?
Bucket List 100 he means don’t lose tungsten in the pool. Never touch the tungsten to metal :)
Thats an idea with any sort of tig welding, is a proper pita lol
@@kf8575 ok so if you had 1700 hours of tig welding to do then what would be the number 1 thing your paying attention to in order to save time?
Can you just keep adding more rod to go faster?
Can you turn up the heat and risk destroying the part?
Can you turn up the gas to make it better?
Your acting as if my comment was terrible and completely out of context when in reality the only thing that could slow him down would be dipping his tungsten and having to resharpen it over and over again right?
@@tylerhensley2312 dont get your panties in a bunch dude, was a joke for crting out loud😄
Sharpen a few up, in a little tube in your boilersuit pocket and your good to go. Anyone that makes out they dont ever dip a tungsten or get a drip of filler wire contamimate it is a bullsh***er. Last thing needed is to have to climb down from an awkward spot to grind up a tungsten
superb welding skill especially considering the access to your joints .
Wow this is some great tig talent 👍👍 much respect
Welding in the pipe rack ain't got shit on y'alls work bro, good job brotha I can only imagine how bad your body aches after being all twisted up inside that spaghetti mess much respect bro
Correct. Started welding in 1976 retired in 2017. Not only is it tough work but the cold steel will take a toll on you. Hip replacement. Bad knees both scooped to remove bone chips. Receive multiple qourtazone shots in back and shoulders. And have macular degeneration. I miss working with the guys but don't miss crawling around in tanks and boilers
@@garyschroeder3242 1976 - 2016 👍
To those who want to know welding try by all means to practice right and left hand welding. By so doing you will be broadening your chances of being a preferred welder.
You have to be ambidextrous, the 6G tests this.
When you are out in the field welding on boilers you definitely going to need to be able to run a tig with either hand
The real boy under the hood 🇺🇲🛠️⚒️🇺🇲 Boilermakers
I invite you to the official facebook. facebook.com/WeldingFreak-1170869266332695/
BOILERMAKERS 🇺🇲🛠️🇨🇦⚒️🛠️🔥🇨🇦🇺🇲
Im retired now but when I did it we didn't tig it all the way out
Boilermakers are the best simply Put. They can do it all.
yeah bunch of stray arc on that pope at the beginning
Tomorrow ima go apply for boilermaker local 92.. how u like the boilermaker union? Are u always busy?
Did you get in?
I've retired now, done my share, but looking at what you are doing one word, Amazing 😎
They dont even shoot them weld they hydro that it. Welding gods my ass the hood were a dead give away.
What about the hoods? Just cos theyre not expensive? So in your opinion what should they be using?? Speedglass? Optrel? 99% of auto lenses are absolute dogshit for tig welding with restricted line if sight, let alone when using a mirror.
@@kf8575never had a problem 😂😂😂😂 because I’m not a loser hiding in pipes who will be sitting on bed my entire life when I’m older due to having a busted body.
S86 IS A BADASS
How come you guys don’t weave your caps it almost seems like you’re just laying the wire down I’m guessing WPS?
Boilermakers aren't allowed to weave a cap or any other weld for that matter. Stringers only, you are not supposed to go more than 3x wider than the diameter of your rod. No jack stand walking the cup BS their. Peace
Nitro junkie I never knew pipe got capped this way till recently I always thought it was weaved in for some reason. I’m on my last semester in college welding and I’ve never thought about being a boilmaker looks hard but interesting
@@Wanglicker42235it’s a shit job that will leave you broken.
Where did he get the owl looking hood
I love this job.ihope i will become profesional tig welder someday
Kaa mou-te-wehi e hoa ma, tino ataahua a koutou mahi.dat be a "Babcox n Wilcox" boiler, neha.. kaapai ra..boilie/welder.. Aotearoa..kia ora...thnx👍
nice welding..👍
My job 25 years in France !
Gravey, they prolly ain't making shit.
Stacking dimes. Yall are some badass Tig hands
Who makes the confined space hood seen in this video ?
Oh that wall
I’d love to see another video of this sorts
Never was a great welder.i miss boilermakin though
Cool. I love welding even though I'm really new at it and am not very good. I want to get better at welding with my powertig welder.
✌👈👉🤘👆👇✌👍🖖🤘🤙🖐✋👌👍👎✊👊🤛🤜🤚👋🤟✍👏👐🙌🤲👁🤝%100
Good to see some class TIG pipe welders, this is high quality welding.
@Sean Kean That is correct but under the old certified classification in the Boiler making trade they were termed Pipe welders and most welding registers Lloyds and several others were, and still are registered as Pipe Welders, I think ABS is the exception as you may guess.
@Sean Kean No problem, ABS is the American Bureau of Shipping - US equivalent to Lloyds shipping. I think a lot depends on which country you are in as there are often differences in reference between them, often the US going its own way.
@Sean Kean I'm from the UK but worked for 10 years in Chicago some years ago but I had given up the tools well before that.
@Sean Kean Cheers have fun.
Very good looking welds. I wish I had half your talent!
朋友你是那个国家的？这个是锅炉焊接最简单的，有机会我教你
Is it true welders in Poland only make $3-8 a hour....? That's just absurd
Experienced welders in Poland have much more. But at the beginning of my career I had a similar bid.
Tyle zarabia się w Polsce . Jeśli usrednic zarobki spawaczy kotlowych. Smutne ale prawdziwe.
@@bonerDB jako spawacz dorabiam ale o 8dolcach nie ma mowy. 5$/h..
@@bombaWypierdoli dlatego jebac spawanie w PL. W NL mam 19 e netto I wyjebane
Cost of living very low in poland. Thats why they flood into western europe, pull the racist card and undercut local tradesmen in order to get work, to then pss off home after a couple of years👍
Root
Hot
Fill
Cap
Repeat!👌
Awesome!!!!
Retired Boilermaker 35yrs, all them non-welding video guys who make welding videos should watch this video, this is why Boilermaking isn't for pipe welding bench welders.
Oh for gods sake be quiet 😂and stop bragging like you’re not replaceable.
My job forever boiler
I am doing this in my welding class Corbin was coming out OK but the carbon and stainless filler wire or you have to pump argon in the pipe is difficult Masking tape keep catching on fire
Hello everyone.I watched this video,and that's what I do.Can anyone recommend a company that needs welders?I use it equally with my left and right hand,I also use a mirror....etc.Thank you very much.
Good welding where are you from?
Looks like good money. You probably have a few tungsten rods sharpened up in case you accidentally dip your electrodes huh?
Hows it going? I'm just wondering where did you buy that small mask or you made it? Have a good one.
Dont under estimate the skill level required here, expert level required.
No offence but tig welding does get much more difficult than this. These are all fairly open access welds, I am a nuclear tig welder on submarines and almost all of our welds are far more restricted than these ones shown. The welding in this video is skillful but its far from the most demanding Tig welding out there.
that guy is a LEGEND THUMBS UP BRO :)
I love my work,,welding man👍👍👍👍
Teuku Ilfan same bro 👍👍👍
Witam. Super robota i mistrzostwo👍👍 Mam również pytanko. Zawsze chciałem taką robote dorwać ale nie zawsze się udawało. Chciałbym się zapytać jakie uprawnienia zrobić na taką robote?? Znaczy się w jakiej grupie materiałowej FM4 czy FM6 bądź też FM5 która z tych?? Oraz czy wy spawając te rurki ,rureczki użtwacie również metody Tig-lift jak to robią w USA lub UK?? Oraz czy robić łączone 141/111 czy każda osobno na rure w pozycji 6G??
Sorki za tyle pytań ale od niedawna się tym interesuje chociaż spawam od 15 lat Tig i Mig z tym że przeważnie nic specjalnego na zakładach nudne powtarzalne elementy😨
Z góry dziękuje za odpowiedź
Pozdrawiam
Dobra robota chłopaki👍👍👍💪💪💪 Dziwne że wy spawacie z wolnej a mi kazali kręcić na próbkach, ciekawe. Swoją drogą takie pytanko jakie tam tigi macie 230V czy 400V i jakie marki?? Pytam bo chcę kupić tiga właśnie z przeznaczeniem na takie roboty.
Pozdrawiam i tak trzymać👍👍👍
Ai sim caldeira de pressão ai eu conheço minha área trabalha de parceria
Jak się nazywa fioletowy preparat którym pokryte są elementy przygotowane do spawania ?
S 86 man from an aerospace thirty year welder ..you are fantastic
Beautiful !!
Fuckin hell
Big buck$$$
Excelente. Extraño mi trabajo en calderas. Saludos 😇🙏
sick skills brothers
What are song is this?
3:45 , can anyone tell me where a bood like that can be found?
Polacy to najlepsi fachowcy na swiecie, pozdrawiam.
Tube welders can make some money if there fast lol
UPS 55 Sekunden Das Rohr innen nicht geschliffen.
Impresionante enhorabuena mucho nivel es una pena q no haya máscaras para espacios reducidos mejores q esas de cuero , verdaderamente penoso !!felicitaciones os admiro
I can watch people welding with a powertig all day.
Ремонт ПГУ ? Чудная работа , главное удобно......
esto es soldar es complicado x la incomodidad aqui dominar con ls dos manos
Wow impressive. I had to do a quick repair during a shutdown week. The re tubing job was a few months away. Not that big of a boiler. Would hammer bulging tubes in. A few blown tubes so close together on the wall had to cut a window in the front. weld the back and sides I couldn’t reach through the window I cut out of the tube then weld the window on the front of the tube. I was a pipe welder not a boiler maker. I have no idea if it was something you should do or not. Just had to get it ready to make steam in a few days. I wouldn’t put my stamp on it. The twin boiler was already down for new tubes no steam the plant would be closed. Held up until they had it re tubed. I was young this was back on the 60’s. To code or not to code?? I had a ASTM stamp as I recall. It got three passes almost half only on the inside.
I been a boilermaker a long time and I still say those walls are seriously challenging 😂
where can i get mask for welding?
eso es elite si señor !!enorabuena desde españa a tu lado soi un humilde soldador !me suscribo amigo !!
حمد الله عندي هذه العمل أريد أن أذهب الي اروبا أنشائ الله
Anybofnyou welders know Ken Chaney
Just like eating Ice cream 😀....be safe #1
Se nota que este colega desempeña muy bien su trabajo de soldador de tubo caldera .
The welds are very good. The fit up on the tubes in the thumbnail is not good. Some of them have a bad dog leg. The membrane on the new panel should of been split to straighten the tubes up. Most weld techs or even the customers would through and fit over the fit up on the panel.
Shush or post a video of you doing better.
Walk cup fools!!! China busting it out better and faster. Step it up welds look rolled, undercut, and inconsistent. Remember, it’s TIG it should be looking hell lot better. Looks like you stick weld that
Got a FB QC here.
They’re boilermakers 😂 they’re not allowed to walk the cup for some stupid unknown reason because they give the exact same results… stringers just look like shit.
- Haha... @ 5:23 welder / S - 86 That's a "top-of-the-range" field weld. Keep up the GREAT work!
It was, until he ruined it by running a file/grinder around the toes of the cap. That fails QA here in UK on any high spec work, due to removing wall thickness👎
@@kf8575 - Haha... really? That joint isn't being fitted in a nuclear powered submarine for you to claim that it wouldn't pass UK's code of inspection. I'll tell you what, if you were a QA on one of my field construction, conventional boilermaker jobs and, you rejected that weld for your claim of wall thickness removal.... that would've been your last weld inspection on that job.
I love this game area....
Truly...
Que buen trabajo y muy buena la soldadura,un saludo colegas desde Uruguay
Dude that's a sweet welding hood what brand is that and whered you get it?
sKeM2k9 did you ever find out what it was?!
🙋♂️🙋♀️🔱🗽👍✌
Salut 👋 les mec un plaisir de voir cette vidéo ça me donne un coup de nostalgie merci 🙏 pour se partage et bonne continuation et courage
Это где? Сколько платили примерно?
Very good thanks is it down hill from 3/9 o clock to 6?
Floor tubes are down hand for the over head part
Это тэц или грэс. Но стали не хм и не р-91.
Nie wiem jak Ci się udało z przetopem z uchwytem w dół. Muszę popróbować.
Kolega podaje drut z góry, spawa się w parach.
Quá tuyệt vời 👍
mialbys jakieś wskazówki dla początkujących. Pozdrawiam
A dokładniej o jakie wskazówki ci chodzi? Bo wiesz, ten temat jest bardzo rozległy.
Welder's do it in all positions
Электростанция походу
ta robota to moje marzenie, tylko gdzie nauczyć się spawać rury?
Energop Sochaczew
Na jakim prądzie spawałeś ? ładny pion ci wyszedł na elektrodzie.
Nie pamiętam dokładnie, plus minus 70A
Katastrofa..jako lose
Przetopy 1 klasa ;)
Elek
elephantsting. oo,u
wtfffff dude this is insane!! How you get your tig torch in such a tight space, nevertheless to weld pipe.... kudos man
You learn how to push the limits on just how far you can pull that tungsten out. Lol. And how to feed the wire from the inside. And how to feed wire for your tube partner. Them ain’t pipes BTW, them is tubes , big difference……
@@nolankirkwood9655in name only 😂
@@lonewolftech actually, pipe has a seam, tubes don’t. Also pipe is measured using the inside diameter, boiler tubes are measured using the outside diameter. If you had went through an apprenticeship you’d know that.
how did you started working on the boilers
Join a Union. Find the local Boilermaker hall near you and apply
очень круто bardzo dobze
Mon boulot pendant 25 ans !