Hello jeff...can we autolaunch the dolphin using frisbee/wing throw style? I already had my fingers clipped by the 7 inch props during launch...aauochhj
Hi Jeff If BLHeli doesn’t show the low voltage cut off, does it mean there is no cutoff for that esc? And do you connect the BLheli configurator thru the FC usb plug? I used a BLHeli usb dongle directly to the esc, which is not so convenient 😅
Hey Jeff, thanks again for your videos! May I ask something? Let's say I have the matek board (the 405 like this one) and want to install it on a different plane, are these settings OK and need some adjustments, or it's very different and has to be set again from 0? Thanks!
Hello sir I know cg point is marking but how can balance CG properly like your atomrc dolphin? And can I copy your pdi tuning to get smooth flying sir?
In autolaunch mode, we don't need to raise throttle, right? Then after throwing the plane, we will raise the throttle (to 50-70%), did I understand correctly? And do we set switch for autolaunch and angle mode are activated at the time?
arm in autolaunch, raise the thottle to max. the plane will throttle up to the autolaunch idle throttle you set, then you throw it. after it detects the throw it will raise throttle to the autolaunch throttle and climb out. after autolaunch has completed, or you touch the sticks then your sticks will start working normally.
Thank you for this video, will help my problem of the auto lunch! its new and didnt know how to set the correct values! May I ask if this is the stock motor or you can set these values to every motor? I have a 1500kv motor, 7x4.5 prop and 6s battery, is it ok or the throttle will be too much? Thanks!!!
Too much throttle is never a problem. You can also can apply these setting to other crafts and different motor/prop setups. When setting up autolaunch I start with max setting and then tune it down from there.
thanks for this config u have helped me setup my first fix wing, 2 questions though, what switches should i setup (flight mode, buzzer rth etc.) Also do you have the stock electronics on your plane like the 2306 motor and 30a esc from atomrc? Im asking as i want to copy it exactly so that i can have my plane working with the stock electronics. Thanks :)
Yes, in this video, I have the stock electronics, motor, esc, and prop. I'm making a video right now on my radio setup, too. It should be out on Saturday or Sunday.
Check this for the gps, 8:29 gps on uart 4, 8:49 GPS For nav and telemetry, 15:41 at the top GPS for navigation and telemetry. Then take it outside and wait a couple of minutes for it to get a lock. Once it has a lock and 6 satellites it remembers your general location and will lock satellites faster then next time you power it up. Let me know if this works.
How are the control surfaces set? I just got a dolphin and the right side is slightly higher than the left in manual mode while level. Kinda new to fixed wing. I did succeed flying the penguin.
just bought one using your code last Friday hope you get some commission you have been so helpful
Thank you so much. I'm glad these videos help you out.
@@JeffDoesThis yes thank you so much. Hopefully you post a radio video so I could see how you set it up.
I’ll try the idle increase with my S800 tomorrow. Good video
Thanks just finished my dolphin.
Lot of info there as new dolphin builder. Thanks for sharing the great 3D files.
My pleasure!
Hello jeff...can we autolaunch the dolphin using frisbee/wing throw style? I already had my fingers clipped by the 7 inch props during launch...aauochhj
Thanks Jeff for all of your very helpful videos that help us out. I appreciate it.
Your welcome! Enjoy your flying!
Hello Jeff, can you show how your flight modes and switches are currently set?
Hi Jeff
If BLHeli doesn’t show the low voltage cut off, does it mean there is no cutoff for that esc?
And do you connect the BLheli configurator thru the FC usb plug?
I used a BLHeli usb dongle directly to the esc, which is not so convenient 😅
Hey Jeff, thanks again for your videos! May I ask something? Let's say I have the matek board (the 405 like this one) and want to install it on a different plane, are these settings OK and need some adjustments, or it's very different and has to be set again from 0? Thanks!
From one flying wing to another, you should be okay.
Thanks for sharing this. 👍
You bet!
Hello sir I know cg point is marking but how can balance CG properly like your atomrc dolphin?
And can I copy your pdi tuning to get smooth flying sir?
In autolaunch mode, we don't need to raise throttle, right?
Then after throwing the plane, we will raise the throttle (to 50-70%), did I understand correctly?
And do we set switch for autolaunch and angle mode are activated at the time?
arm in autolaunch, raise the thottle to max. the plane will throttle up to the autolaunch idle throttle you set, then you throw it. after it detects the throw it will raise throttle to the autolaunch throttle and climb out. after autolaunch has completed, or you touch the sticks then your sticks will start working normally.
when i hit "read setup" in BLHELI it says "reading setup finished" but nothing is showing up, do you have any tips? ESC is powered with a battery
What ESC is it, make model?
Thank you for this video, will help my problem of the auto lunch! its new and didnt know how to set the correct values! May I ask if this is the stock motor or you can set these values to every motor? I have a 1500kv motor, 7x4.5 prop and 6s battery, is it ok or the throttle will be too much? Thanks!!!
Too much throttle is never a problem. You can also can apply these setting to other crafts and different motor/prop setups. When setting up autolaunch I start with max setting and then tune it down from there.
@@JeffDoesThis I am building it right now and these settings are very valuable to me! Thank you for this!!!
No problem!
Also, check out this video - It has some updated inav settings in it for the PID Tuning - ruclips.net/video/ezTsxAiL-8U/видео.html
Excellent video.... how do you set-up the channels for the pan and tilt in your radio and Inav?... I think I am doing something wrong thaks.
I'm making a video right now on my setup and how to do it. It should upload on Thursday.
What trouble are you having?
What mode are you launching in ? I launch mine and starts out fine then just rolls over and crash …
I launch in Angle Mode.
thanks for this config u have helped me setup my first fix wing, 2 questions though, what switches should i setup (flight mode, buzzer rth etc.) Also do you have the stock electronics on your plane like the 2306 motor and 30a esc from atomrc? Im asking as i want to copy it exactly so that i can have my plane working with the stock electronics. Thanks :)
Yes, in this video, I have the stock electronics, motor, esc, and prop. I'm making a video right now on my radio setup, too. It should be out on Saturday or Sunday.
Thanks jeff, I'm hoping to maiden mine this weekend! Sadly it won't arm and no there are 0 satellites connecting to the gps@@JeffDoesThis
Check this for the gps, 8:29 gps on uart 4, 8:49 GPS For nav and telemetry, 15:41 at the top GPS for navigation and telemetry. Then take it outside and wait a couple of minutes for it to get a lock. Once it has a lock and 6 satellites it remembers your general location and will lock satellites faster then next time you power it up. Let me know if this works.
How are the control surfaces set? I just got a dolphin and the right side is slightly higher than the left in manual mode while level. Kinda new to fixed wing. I did succeed flying the penguin.
the trim, either on controller or in inav
Where do you plug an epressLrs receiver in the atomrc f405 navi flight controller like in your model
You plug into any available UART on the flight. It's a 4 wire connection, ground, positive, TX, and RX. If use UART #1.
@@JeffDoesThis thank you very much 👍✈️
Great vid! thanks for sharing.
Thank you!
Do u have to put it in stability mode