Just finished cleaning up my wiring also, waiting on those sinewave controllers that you recommended to get in. I got the 12 volt convertor in, with new lights, got rid of the alarm, and added a $20 NFC Lock switch for the "ignition" for $25 in place of the alarm, (about half the size), Got my Thumb Throttle mod completed and its SOOOO much better than the trigger, less fatiguing for me. I also re-did my Phase wires with XT150 6mm bullet connectors. I added XT90 connectors with antispark to the battery connection so I don't have to listen to that "pop" each time I plug the battery in lol. I know XT90 is above what was in there, but, I changed out my Battery's BMS and cables also to match, I had a 300 AMP Smart BMS from a project that I ended up going Lifepo4 with, so the Li Ion BMS will get its use. I just set the current limit/shutoff to the same limit as the one that was in there, and I can now monitor the balance voltage of the 8 sets of 16, along with the temperature via Bluetooth. Looking forward to the controller installation video, So I can follow along. Thanks again for another great video!
Thank you for your video. I have exactly your scooter and I been looking how to rewire my controller for a while. Luckily I found your video. Thank you 🙏🏾 thank you 🙏🏾
Could you tell me how to rewire my horn correctly please. I had the same 60v front & rear indicators which I removed, but somewhere in spaghetti junction the front & rear indicator wires were looped in with the head & tail lights and horn wires, to the controller and switch. But since I've removed the indicators, my horn only works when my lights are switched on and not when they're off
You sound like you know whats up.. though i do have one question...for the motor phase cables, u have the green and blue swapped.. mine go from color to color g-g. B-b. Y-y. Should i switch them?
If your motors are turning in the right direction (forward) then leave them as they are. The only reason you would swap the colors is if the motor was turning backwards. It depends on the motor/controller combination. Controllers with a “learn” function like the Yunli Sinewave controllers, will learn the phase wires regardless of how you have them wired, so it wouldn’t even matter in that case.
Hi can you help me pls, i got the same controller model, i plugged some wires between 2 controllers wrong and now the main controller wont turn motor, i open the controller and it blinking red, i tried unplug everything and re done everything all over again, the controller still blinking red, nothing burnt just blinking red, any idea how to reset this red light so it will allow power to motor again?
Now wtht the new controllers from FLJ , i got problem with the low and high brakes, it only has 2 wires black and grey for the brakes sensor, wheb my battery fully charged the brakes wont work , when my battery drop to about 40% then the brakes starts kicking in really hard , should i cut off the grey wire and connect to the positive power see if the high brake will kick in at fully charged battery?
@mikenguyen4207 The brake sense line only has two wires and they do NOT carry voltage. The brake sense line is just an open/closed indication to the controller triggered by switches in the brake lever assemblies. Do not apply voltage to the brake sense line. If when you pull either brake lever, your brake lights come on, then the brake sense is working properly. Watch this: ruclips.net/video/gLE3i_xoe3I/видео.htmlsi=EgTRFNq2mX5DYgZ6
The JP controllers are not good and I wouldn’t recommend them. I replaced mine with the Yunli sinewave controllers which are far superior. banggood.onelink.me/zMT7/6c7rcb4s ruclips.net/video/nVbxYaVWYAk/видео.htmlsi=ttW9fLlQwjAtCn4D ruclips.net/video/RRiVyBfwXf8/видео.htmlsi=oFr_Dzigy09fhxp3
Your customize scooter gonna be bad ass... i just noticed when i unfolded my handle bars that red lever of my scooter is down hitting on scooter deck and i been riding like that since...does it make a difference leaving it down i guess the proper position is keeping the red lever up.... i also tried to unfold the scooter but forgot how i ended up pressing the red lever upwards instead of down where i currently have it but forgot its the other way around i have to push down on the side silver lever then down on the red lever to fold the scooter handle bars down????
Part 2 will not make your motor work. If you followed part 1 correctly and your motor does not spin then your controllers are bad. The flashing box is an indication that there is an issue between the controllers and the motors. If the wiring is correct, then your controllers are the problem.
The JP controllers that came in mine did not have a learn function so the blue and green needed to be swapped for the motors to turn in the forward direction. It came from the factory that way. I now have the Yunli controller setup which has the learn function, so this is not necessary for those controllers.
@@Desert-Ecruising ok my friend thanks. One more question ❓ due to the fact I had an accident with ti30 now I will rebuild it. Could you tell me if you know how can I put switch with key??
@MotoTaz86 if you’re rebuilding, I highly suggest you switch over to the Yunli setup. It’s so much better than the JP. Yes, you could add a keyed switch. Email me and I’ll help you out : maikemarx@gmail.com
The stock JP controllers don’t have a learn function. For the JP controllers with these specific motors, the blue and green must be swapped for the motors to spin forwards. The far better Yunli controllers I am using now have a learn function so the colors don’t matter, the controllers will learn the motors regardless of which color goes where.
Since you look like u know what’s up. I purchased one on Amazon and when it arrived I checked the voltage and charged it. It lost 3 volts in short time I disconnected the alarm and checked it after some time. It didn’t loose anywhere near the voltage this time. I was ready to put it on the road and touched the display to turn it on and noticed that the power button was extremely hot. I quickly disconnected the battery and waited for it to cool. The dealer promised me a new display but I am not certain if I should wait for the new display. I only have a week left in order to send it back. I don’t know what to do I have not even road it yet and I am presented with all these problems. What so u think should I keep it or send it back before the 30 day limit. Scott Farley
It’s a great scoot but you shouldn’t have to deal with that. I’d send it back while you can. That’s the benefit of ordering through Amazon. Then, if you like, u can email me and I’ll help you look for a scoot in whatever your price range is and based on your needs. maikemarx@gmail.com
Hello. Thanks for that video! I have one problem : When I turn on the scooter. No problem. But when the Eco turbo switch is pressed, and released, so now it is released, my front motor turn alone. It is at a small speed, I think 25kilometers/hour. And the switch are not doing what they need to do. Dual single, etc. Any idea? Thanks.
Hey has anyone had their scooter just stop working? Mine was working great then suddenly wouldn’t drive, quickly after that it powered off and wouldn’t start up. I tried the alarm button reset and then by passed the alarm and removed it. Now one accessory light will work, but the rest of the scooter won’t power on. Any ideas for next steps?
Hy man my horn stopped working on the ti30 and puff of smoke happend from the controller and now I need new ones how do I remove the old ones I can’t finds the mounts
@@Desert-Ecruising sorry for the confusion yes I mean the controller mounts I’m getting the sinewave controllers bc my old one made a small puff of smoke and every thing works but the head lights and horn
I have a sine wave foc controller dual monitor 60v45amp whole lot of orange wires I have no idea what to do after phase wire and hall sensor can see display wire can you video chat with me please maybe 10 minutes pleSe please
Just finished cleaning up my wiring also, waiting on those sinewave controllers that you recommended to get in. I got the 12 volt convertor in, with new lights, got rid of the alarm, and added a $20 NFC Lock switch for the "ignition" for $25 in place of the alarm, (about half the size), Got my Thumb Throttle mod completed and its SOOOO much better than the trigger, less fatiguing for me. I also re-did my Phase wires with XT150 6mm bullet connectors. I added XT90 connectors with antispark to the battery connection so I don't have to listen to that "pop" each time I plug the battery in lol. I know XT90 is above what was in there, but, I changed out my Battery's BMS and cables also to match, I had a 300 AMP Smart BMS from a project that I ended up going Lifepo4 with, so the Li Ion BMS will get its use. I just set the current limit/shutoff to the same limit as the one that was in there, and I can now monitor the balance voltage of the 8 sets of 16, along with the temperature via Bluetooth. Looking forward to the controller installation video, So I can follow along. Thanks again for another great video!
Thank you for your video. I have exactly your scooter and I been looking how to rewire my controller for a while. Luckily I found your video. Thank you 🙏🏾 thank you 🙏🏾
Great videos mate
You are the man. Perfect vídeo. Wait for the part 2🙏🙏
Should be uploading part 2 by next Saturday.
I had difficulties in assembling the lights, the part 2 will be Great 😊😊
Could you tell me how to rewire my horn correctly please. I had the same 60v front & rear indicators which I removed, but somewhere in spaghetti junction the front & rear indicator wires were looped in with the head & tail lights and horn wires, to the controller and switch. But since I've removed the indicators, my horn only works when my lights are switched on and not when they're off
This will help: ruclips.net/video/DuVWxyx59TM/видео.html
@@Desert-Ecruising thanks dude! I'm gonna open the deck up tomorrow and check where the wrong connection is
You sound like you know whats up.. though i do have one question...for the motor phase cables, u have the green and blue swapped.. mine go from color to color g-g. B-b. Y-y. Should i switch them?
If your motors are turning in the right direction (forward) then leave them as they are. The only reason you would swap the colors is if the motor was turning backwards. It depends on the motor/controller combination. Controllers with a “learn” function like the Yunli Sinewave controllers, will learn the phase wires regardless of how you have them wired, so it wouldn’t even matter in that case.
Hi can you help me pls, i got the same controller model, i plugged some wires between 2 controllers wrong and now the main controller wont turn motor, i open the controller and it blinking red, i tried unplug everything and re done everything all over again, the controller still blinking red, nothing burnt just blinking red, any idea how to reset this red light so it will allow power to motor again?
You can email me and I’ll try to help: maikemarx@gmail.com
Nvm it fried, i bought another
Now wtht the new controllers from FLJ , i got problem with the low and high brakes, it only has 2 wires black and grey for the brakes sensor, wheb my battery fully charged the brakes wont work , when my battery drop to about 40% then the brakes starts kicking in really hard , should i cut off the grey wire and connect to the positive power see if the high brake will kick in at fully charged battery?
@mikenguyen4207 The brake sense line only has two wires and they do NOT carry voltage. The brake sense line is just an open/closed indication to the controller triggered by switches in the brake lever assemblies. Do not apply voltage to the brake sense line. If when you pull either brake lever, your brake lights come on, then the brake sense is working properly. Watch this: ruclips.net/video/gLE3i_xoe3I/видео.htmlsi=EgTRFNq2mX5DYgZ6
can you give me link to buy this controller please? and what is its advantage over the standard one?
The JP controllers are not good and I wouldn’t recommend them. I replaced mine with the Yunli sinewave controllers which are far superior.
banggood.onelink.me/zMT7/6c7rcb4s
ruclips.net/video/nVbxYaVWYAk/видео.htmlsi=ttW9fLlQwjAtCn4D
ruclips.net/video/RRiVyBfwXf8/видео.htmlsi=oFr_Dzigy09fhxp3
Your customize scooter gonna be bad ass... i just noticed when i unfolded my handle bars that red lever of my scooter is down hitting on scooter deck and i been riding like that since...does it make a difference leaving it down i guess the proper position is keeping the red lever up.... i also tried to unfold the scooter but forgot how i ended up pressing the red lever upwards instead of down where i currently have it but forgot its the other way around i have to push down on the side silver lever then down on the red lever to fold the scooter handle bars down????
Thank you but my rear motor is still not moving. It still show the little box on the display
I’ll be waiting for part 2 ❤🙏
Part 2 will not make your motor work. If you followed part 1 correctly and your motor does not spin then your controllers are bad. The flashing box is an indication that there is an issue between the controllers and the motors. If the wiring is correct, then your controllers are the problem.
Double check all the display connections. Make sure the pins in the connectors are secure and not backed out.
Hello why did you connect green with blue and opposite? At the controllers?
The JP controllers that came in mine did not have a learn function so the blue and green needed to be swapped for the motors to turn in the forward direction. It came from the factory that way. I now have the Yunli controller setup which has the learn function, so this is not necessary for those controllers.
@@Desert-Ecruising ok my friend thanks. One more question ❓ due to the fact I had an accident with ti30 now I will rebuild it.
Could you tell me if you know how can I put switch with key??
@MotoTaz86 if you’re rebuilding, I highly suggest you switch over to the Yunli setup. It’s so much better than the JP.
Yes, you could add a keyed switch. Email me and I’ll help you out : maikemarx@gmail.com
What was the reason for switching the yellow blue green wires?
The stock JP controllers don’t have a learn function. For the JP controllers with these specific motors, the blue and green must be swapped for the motors to spin forwards. The far better Yunli controllers I am using now have a learn function so the colors don’t matter, the controllers will learn the motors regardless of which color goes where.
how i change the rear motor ?
Since you look like u know what’s up. I purchased one on Amazon and when it arrived I checked the voltage and charged it. It lost 3 volts in short time I disconnected the alarm and checked it after some time. It didn’t loose anywhere near the voltage this time. I was ready to put it on the road and touched the display to turn it on and noticed that the power button was extremely hot. I quickly disconnected the battery and waited for it to cool. The dealer promised me a new display but I am not certain if I should wait for the new display. I only have a week left in order to send it back. I don’t know what to do I have not even road it yet and I am presented with all these problems. What so u think should I keep it or send it back before the 30 day limit. Scott Farley
It’s a great scoot but you shouldn’t have to deal with that. I’d send it back while you can. That’s the benefit of ordering through Amazon. Then, if you like, u can email me and I’ll help you look for a scoot in whatever your price range is and based on your needs. maikemarx@gmail.com
I had this issue with the key/voltage display. I just jumped the switch and use the voltage display on controller.
Can you by past the remote for all push start controller
If the alarm is the same as in the video, then you should be able to bypass it in the same way. A lot of scoots use that same alarm module.
how do you take all the parts off i cant remove my battery or controllers... its very tight and hard move...looks stuck???
Watch from 1:20 to 3:40
ruclips.net/video/DgSNKXOZ680/видео.htmlsi=BqheJ10JTDfoU0lb
Hello. Thanks for that video! I have one problem :
When I turn on the scooter. No problem.
But when the Eco turbo switch is pressed, and released, so now it is released, my front motor turn alone.
It is at a small speed, I think 25kilometers/hour.
And the switch are not doing what they need to do. Dual single, etc.
Any idea?
Thanks.
If the wiring is all correct, then I would have to believe the controllers have an issue.
@@Desert-Ecruising yes, replaced and good now, but now gear 1 and 2 in Eco are 4 and 14 km/h.. Sad. Faulty new controller..
To me eco mode is useless. I can still go as slow as I want in turbo mode just using the throttle.
@@Desert-Ecruising sometime I found it useful and need that Eco switch too for magnetic speed limit 😝
Hey has anyone had their scooter just stop working? Mine was working great then suddenly wouldn’t drive, quickly after that it powered off and wouldn’t start up. I tried the alarm button reset and then by passed the alarm and removed it. Now one accessory light will work, but the rest of the scooter won’t power on. Any ideas for next steps?
I can help you troubleshoot it if you email me: maikemarx@gmail.com
I’ve emailed you, thanks!
@@justinalvis4409I haven’t received your email. Did u send it to maikemarx@gmail.com?
I have see some people have had a wire come loose on bms. Pirate made a video on fixing it.
Hey I need help i am using this but unfortunately showed the warning sign in the display than its not working but power is on. What I have to do?
Hy man my horn stopped working on the ti30 and puff of smoke happend from the controller and now I need new ones how do I remove the old ones I can’t finds the mounts
Do you really mean the controllers? They are inside the chassis. Do you mean the throttle? What mounts are you referring to?
@@Desert-Ecruising sorry for the confusion yes I mean the controller mounts I’m getting the sinewave controllers bc my old one made a small puff of smoke and every thing works but the head lights and horn
I think from what I can tell there is a pice adhesive but am not fully sure and do not want to brake anything
@D-rek420 yes, it’s just adhesive thermal tape holding them in. Just pull them up.
@D-rek420 also, if you’re getting the Yunli Sinewave controllers, get the kit with the Yunli DS20 throttle.
I have a sine wave foc controller dual monitor 60v45amp
whole lot of orange wires I have no idea what to do after phase wire and hall sensor can see display wire
can you video chat with me please maybe 10 minutes
pleSe
please
How do you take out the controller my made a puff a smoke and I want them out until I get new ones