@@littlebittathisnthatfirear8048 a 4056 is a battery charge circuit. Its only designed to charge one battery at a time. Putting them all in parallel, each charging only 1 battery, like in the video, is the correct way to use them There is a… very very terrible way to use them to charge batteries in series, it requires 4 separate decoupled power supplies and if you hook them up wrong your batteries will all explode
@@littlebittathisnthatfirear8048these Little Blue board are litium battery charger and are called 4056 because thats the game of the integrated circuit on the board itself, normally they operate by themselves and if he hadnt done any modification to them they would still works separetly and if you plug One USB on One of the board It would only charge One battery, but he connected the inputs of all the board together in parallel (all + connected together and all - connected together) and with that modification he can charge all batteries with One USB instead of 4, let me know of you didnt understand something, i probably used some weird langage form since english isnt my First language
But ofcourse the storage capacities of each batt are not the same so if you have 1800mah and 2200mah, once 1800mah is full it will indicate charging full while the 2200mah won't be full.
@@alexvalentino2227It will take longer using a USB. At least with a power supply you can supply more amps. The issue with this setup is a loss in power to the boards and you are limited to 2amps for a 4 battery system.
charged mine with an old mini fan:D i just put the battery in and boom i charged it using my charger and now its still working better (i have been doing it for 6 months so yeah its not dangerous [i think...])
Nahh, the TP4056 is fine and all but in my experience. They get really uncomfortably hot, I suggest adding small heatsinks so they won't cook themselves lol
Hey bro can i ask something? İ have got a speaker project and ill use 3 tp4056 while using serial connection on my li ion batteries and they become shortcut and burnt the tp4056 circuits will it work with this circuit if i add 1n4007 diode for every circuit and use batteries same as before?
@@ErCanEverything thanks for help but i need a 12 v tp4056 serial circuit without shortcut. Will diodes help? Can you make a video abt that? İ need 1 with 3 li ion battery and 3 tp4056. Thanks.
Right, i was wondering why waste time. You'd have to wait to fully charge one and then the next and so on. Although charging all at once in parallel with one board might take more time. Heck leave it overnight right!
I was going to ask the same question, nvm now. This guy is just wasting tp4056 boards. I'm very new to this too, but why waste good resource for other things and he's made it more difficult to charge each battery one at a time.
Для тех кто не понял - он подключил аккум к каждой плате по отдельность а вот инпут плат подключил паралельно и запитал все 1 проводом. Все банки заряжаются независимо др от друга
@@mne_normalno_777 а куда спешить, если макс ток зависит от емкости, и у производителей акумов от равен либо 1С либо 0.5С, (С емкость акума в mAh). И предпочтительно заряжать акумы током 0.5С, (дольше служит). У обычной 18650 емкость 2-3 Ah, следовательно ток от 1-1.5 ампер и время заряда будет где-то 2-3 часа. можно и ещё ниже ток сделать, ток время увеличится, а большие токи заряда чреваты деградацией аккумулятора!
@@burkin_alex Это глупое решение. Просто нужно иметь одну нормальную зарядку и подключать к ней хоть 1 хоть 4 хоть 6 банок! А под них можно напечатать корпус, куда вставлять для этого.
Только TP4056 греются так, что расплавят этот элегантный тонюсенький держатель при первой же зарядке 😂 их к алюминиевому рельсу надо клеить, а не это вот все 😂
Собирал раньше похожую. Проблема что уже при третьей плате с акамуятором нагрузка увеличилась до того что гнездо микро юсб долго не выдерживает высокой температуры.
Yes about 3.4A will draw for 4 batteries at 1A charging current of the batteries. Because it will draw about 850mAh from the charger at 5V for each board
@@ultimatesheep Stacking them would connect the outputs and batteries in parallel. That would be rather stupid, because the idea of using 4 TP4056 is to charge each battery individually. He connected the inputs of the TP4056 in parallel without showing it in the video. In general there is nothing wrong with it. It just makes his build look a bit simpler than it is and makes it a bit harder for those who want to reproduce it.
@@gufo_tave Ok. I did not watch the full video, because I know those TP4056 mudules since a long time. If you can use one of them to charge 1 batterie its obvious that you can use 4 of them to load 4 batteries.
Which should I connect in parallel? I connected the inputs in parallel, and the outputs are separate so that each board can be responsible for its own battery. ruclips.net/video/ti0IjZPfojs/видео.html
Connecting lithium ion batteries in parallel if they don’t exactly match each other in chemical properties causes them to rapidly degrade. If you ever see lithium batteries in parallel they were most likely manufactured at the same plant at the same production line at the same day and hopefully their serial numbers are only one apart, otherwise they are quite dangerous
@@JoshinkenOhh bro ! He didn't connected batteries in parallel ! He just connected the inputs of charging module in parallel ! Each batteries are separated by a module.
Nunca faça isso, essas plaquinhas usa 1 amperes de corrente, mas, as bateria precisa ser carregadas com 500mh. o ideal seria carregar 2 baterias em paralelo para cada placa de carregamento.
Не совсем. Это плата как раз нужна для контроля заряда, но есть 2 версии. Та что на видео, нормальная, а есть уменьшенная версия, а точнее не полноценная. Ей заряжать нельзя
Какие все умные. Явно не понимают что 1А можно получить только с охлаждением. Потому что по мере нагрева ТР4056 она сама снижает ток. Но с этим явно никто не разбирался из комментаторов. Сосать с одного USB это как писали бред. Разве что зимой чтобы от него греться. Так же комментаторы не заметили что платки с защитой стоят. Так что максимум что ляжет контроллер который управляет поливиком. Так же если покурить документацию то можно еще пару плюшек нарыть. Но это сами. А так лучше ставить ТР5100. В таком решении она куда лучше и интересней.
Modules are limited to 1A and the phone charger can support up to 3A. The best option is to make one with 10 battery slots and mount it on a 10A charger
Soy yo, o el hizo soldadura en el bat+ junto con la salida del mosfet protector de la batería 🤔? Segun tengo entendido uno es para cargar la batería y el otro es para la salida hacia el aparato.
The positive output and + of the battery are factory connected and the mosfet controls the negative outputs. I connected the type C inputs in parallel so that I could charge them with 1 charger, but otherwise each board is responsible for its own battery. Full Video👉 ruclips.net/video/ti0IjZPfojs/видео.html
@@Gera.1489-110? ТР4056 в пике потребляют 1А, их там 4 штуки. 4-х амперного БП за глаза хватит! Даже если БП будет на меньший ток - это совсем не страшно. Ну, чуть медленнее будет заряжаться. Допустим не 2-3 часа, а 3 - 4 часа… 🤷♂️
I also want to charge 4 18650 batteries with four Tp4056 modules, here are my some doubts can u please clear it😊 1,Should i connect input for modules in series or parallel 2, can i use 12v 1.5amp as input for 4 modules
You need to connect them in parallel and supply with 5V power supply. Depending on the pcs. of the batteries, you will need to use a suitable charger. Example, for 5 batteries you need a 5V 5A power supply.
..edit. Thank You , can i use 5V/2A 🤔 it shows same in ur fullVideo but u use other Generator or Batterie ... i want use it as a Small Powerwall and of this Way i can load whit Solarpvminisystem.
You can use any phone charger. If the maximum current of the charger is 2A it will charge 4 batteries with about 500mAh for each battery, if you put 2 batteries it will charge with 1A for each battery. If you put 1 battery, it will still charge with 1A current
Поделил 2 ампер на все четыре и на каждую банку 500ма и при наборе полностью ёмкости каждая банка отключается и заряд идёт на оставшиеся пока все не заряд не возьмут. Но если окажется что один аккумулятор с более высоким внутренним сопротивлением он будет сажать другие. Не идеальный вариант хоть исполнение 👍
3d yazıcıda cıkarttınız sanırım istasyonu. en sağlamı olmuş ama.pil yataklarını sıcak silikon ile nasıl yapıştırırsan yapıştır. pil sök tak yaparken elle tuttuğum halde pil yatağı kalkıyor her seferinde. bender vidalamayı düşünüyorum 0.5cm lik suntaya.
ТАК НУЖНО 4 ПРОВОДА ДЛЯ ЗАРЯДКИ ОДНОВРЕМЕННО ДЛЯ ЭТИХ МОЛУЛЕЙ ДЛЯ КАЖДОЙ БАТАРЕЙКИ .А МОЖНА НА АЛИЖКСПРЕС КУПИТЬ МОДУЛЬ ЧТО ЩАРЯДАЕТ ОДНОВРЕМЕННО ВСЕ 4 БАТАРЕЙКИ И НЕ БУДЕТ ГРЕТТСЯ
It will be a problem if the individual cells are not balanced (are at different voltages). There is a tutorial that explains why it's good to use one module for each cell.
Я так понял, что он запаралеллил входы плат заряда, а не выходы, иначе сами платы сдохли бы. Лучше питать сами платы от одного источника, чем кучу АКБ от одной платы. Во всяком случае я так сделал.
not worth for me, XTAR chargers cost 15 dollars with 4 slots, LCD screen and some options like storage, test, charge, discharge, are more saver and you can put there all sizes of li-ion cells like 21700 and 26650 big ones, buying the tp4056 for 1 dollar is just waste of money
🔊Full Video👉 ruclips.net/video/ti0IjZPfojs/видео.html
4
😊😊😊😊😊😊😊vv
😊
ল
ɢxɢᴠʜʜʙ🎉ʜᴠʜɪɢʜʜ
The moment you broke out 4 tp4056 i screamed, but thank god you just put them in parallel
Elaborate for a newbie?
@@littlebittathisnthatfirear8048 a 4056 is a battery charge circuit. Its only designed to charge one battery at a time. Putting them all in parallel, each charging only 1 battery, like in the video, is the correct way to use them
There is a… very very terrible way to use them to charge batteries in series, it requires 4 separate decoupled power supplies and if you hook them up wrong your batteries will all explode
@@littlebittathisnthatfirear8048these Little Blue board are litium battery charger and are called 4056 because thats the game of the integrated circuit on the board itself, normally they operate by themselves and if he hadnt done any modification to them they would still works separetly and if you plug One USB on One of the board It would only charge One battery, but he connected the inputs of all the board together in parallel (all + connected together and all - connected together) and with that modification he can charge all batteries with One USB instead of 4, let me know of you didnt understand something, i probably used some weird langage form since english isnt my First language
😊😊😊😊😊😊
Unless you use a BMS it's not safe, because each individual battery has a different charge
You can make it even better. Combine the plus poles and minus poles of each circuit and put it on a powersupply
Real it will work
Right, then you wouldn't have to unplug and charge the next and so on, although it might consume more time to fully charge the four batt at once.
But ofcourse the storage capacities of each batt are not the same so if you have 1800mah and 2200mah, once 1800mah is full it will indicate charging full while the 2200mah won't be full.
@@alexvalentino2227It will take longer using a USB. At least with a power supply you can supply more amps. The issue with this setup is a loss in power to the boards and you are limited to 2amps for a 4 battery system.
Did y'all not watch the video? All 4 are charging at once as all 4 lights were on at the end of the video with only 1 cable plugged in
Making a charger for 18650 batteries from charger units for 18650 batteries.
Wow.
Isn't that what they are for?
@@AckzaTV Yes they are,Thats why they called rechargeable.
The TP4056 is a classic charge module. 😊
Yep
Max load Type C is 5A. This max current is 4A for a 1A on 1 cell. That is norm diy
It doesn't have a max really, it was pushed to over 10 amps on fast charging, so...
@@sw3gmach1ne17 nah, really?
📸cgdgcycn
charged mine with an old mini fan:D i just put the battery in and boom i charged it using my charger and now its still working better (i have been doing it for 6 months so yeah its not dangerous [i think...])
Nahh, the TP4056 is fine and all but in my experience. They get really uncomfortably hot, I suggest adding small heatsinks so they won't cook themselves lol
What tool do you use to weld the wires to the electronics using metal
Soldering iron
Hey bro can i ask something?
İ have got a speaker project and ill use 3 tp4056 while using serial connection on my li ion batteries and they become shortcut and burnt the tp4056 circuits will it work with this circuit if i add 1n4007 diode for every circuit and use batteries same as before?
In the description of this video you will find some useful things that you might like.
ruclips.net/video/p6AyG4ou6-Y/видео.html
@@ErCanEverything thanks for help but i need a 12 v tp4056 serial circuit without shortcut. Will diodes help? Can you make a video abt that? İ need 1 with 3 li ion battery and 3 tp4056. Thanks.
Only a toaster-like ejection device is missing
Just using 1 TP4056 can charge 4 batteries in parallel, regardless of the number. What are the benefits of installing 4 TP4056s?
Right, i was wondering why waste time. You'd have to wait to fully charge one and then the next and so on. Although charging all at once in parallel with one board might take more time. Heck leave it overnight right!
@@alexvalentino2227 i see...thank you sir..🤗👍🏻
I was going to ask the same question, nvm now. This guy is just wasting tp4056 boards. I'm very new to this too, but why waste good resource for other things and he's made it more difficult to charge each battery one at a time.
The module comes with overcharge protection, different batteries has different capacity
why use a module that has protection? while only for charging only
I used a module because this way I charge with the phone charger and once the voltage reaches 4.2V it stops charging
@@ErCanEverything Have the cell after that 4,2v or only the charging power?
Для тех кто не понял - он подключил аккум к каждой плате по отдельность а вот инпут плат подключил паралельно и запитал все 1 проводом. Все банки заряжаются независимо др от друга
Да, но скорость зарядки минимальная. Учитывая,что плата не даёт сама больше 1 ампера....
@@mne_normalno_777 а куда спешить, если макс ток зависит от емкости, и у производителей акумов от равен либо 1С либо 0.5С, (С емкость акума в mAh). И предпочтительно заряжать акумы током 0.5С, (дольше служит). У обычной 18650 емкость 2-3 Ah, следовательно ток от 1-1.5 ампер и время заряда будет где-то 2-3 часа. можно и ещё ниже ток сделать, ток время увеличится, а большие токи заряда чреваты деградацией аккумулятора!
Как зушка
@@burkin_alex Это глупое решение. Просто нужно иметь одну нормальную зарядку и подключать к ней хоть 1 хоть 4 хоть 6 банок! А под них можно напечатать корпус, куда вставлять для этого.
It's a stupid video, and that's why you copy and upload my videos, right?
You don't need discharge protection on tp4056 in this case. Preferred to buy cheaper tp4056 without protection, because here is only charging!
you are correct but I think it is always good to have protection in the even something goes wrong, but no need for discharge protection
Ẻ4errekrjs
платы с защитой меньше греется, потому-что у них нет токоограничивающего резистора на микросхему tp4056, в отличии от плат без защиты
7hugjvhighfjgy
The tp 4056 without protection is also good for charging undervoltage batteries. While the protection one refuse to charge
I have those exact charging circuits that I used in a few projects!
From where to get this battery holder
Can you make a simple discharge for 18650?
4 Parallel using a 5A 500ma charger is going to take forever to charge. For decent charging time use 5V 2A charger!
Where can I supply power to the board from a small solar panel?
You can buy this for $10 on Amazon, although I understand if you want to make it yourself.
I swear if I see one breath air comment in here I'm going to shit myself.
voopoo drag 3 reference
Только TP4056 греются так, что расплавят этот элегантный тонюсенький держатель при первой же зарядке 😂 их к алюминиевому рельсу надо клеить, а не это вот все 😂
один элемент держат не напрягаясь. 2 в параллели заряжал и полет нормальный
Собирал раньше похожую. Проблема что уже при третьей плате с акамуятором нагрузка увеличилась до того что гнездо микро юсб долго не выдерживает высокой температуры.
лучше паять напрямую. токи большие, какой тупись тут выдержит или блок питания?
Там разъем тайп-с и он по входу запараллелен
Используй Т-С у него выше допустимый ток нагрузки
Solo que esos cargadores pueden dar 1 ampere cada uno están jalando un poquito más de la mitad ...
Yes about 3.4A will draw for 4 batteries at 1A charging current of the batteries.
Because it will draw about 850mAh from the charger at 5V for each board
What about reverse polarity protection for circuit
If you are DIYing Li-ion battery chargers... You probably don't need a reverse polarity protection feature, do you?
Чтобы не подключать 4 провода, сделай перемычки через кнопку на каждый модуль. Одного хорошего блока питания вполне хватит на 4 батареи.
Он же так и сделал
Дай пожалуйста ссылочку где можно приобрести подобный держатель 18650?
@@user-sj2dp3lg7iонраспечатал наверное на 3 д принторе
@@user-sj2dp3lg7iTry searching the net, ordered myself some 3 and 4 piece 18650 holders from Ebay.
@@user-sj2dp3lg7isearch SDM PCB battery holder
Wow, cool. 4 modules charging after connecting one only. Thats the next level of wireless charging.
💯💯🤣
I heard they can stack idk prove me wrong
@@ultimatesheep Stacking them would connect the outputs and batteries in parallel. That would be rather stupid, because the idea of using 4 TP4056 is to charge each battery individually. He connected the inputs of the TP4056 in parallel without showing it in the video. In general there is nothing wrong with it. It just makes his build look a bit simpler than it is and makes it a bit harder for those who want to reproduce it.
If you see the full video, you will notice that the input of all modules are connected in parallel
@@gufo_tave Ok. I did not watch the full video, because I know those TP4056 mudules since a long time. If you can use one of them to charge 1 batterie its obvious that you can use 4 of them to load 4 batteries.
the problem for that when you reverse the battery the magic smoke come out...
For this you need 25v 6amp
Haha, that wont even work with a Type C to Type C cable.
Must be slow charging 4 batteries like that
Вместо тп4056,я использую зарядный модуль электронных сигарет.Если сгорит при ошибке полярности,не жалко они бесплатные.
Why you used multiple charging port instead of one pord
Her biri için ayrı modül koymak yerine bir modül ve her biri için ayrı tuş koyabilirdin
What about heat dispassion of tp4056 ....?
Normally, they don't heat up much.
I never use heat dissipation because it goes up to 50c and that's perfectly safe.
So, not necessary.
Great,where are these battery terminals found ?
Check the dark market😅
Can you charge 2 18650 in parallel with 1 TP4056?
Why you didn't connected in parallel way ???
Which should I connect in parallel?
I connected the inputs in parallel, and the outputs are separate so that each board can be responsible for its own battery.
ruclips.net/video/ti0IjZPfojs/видео.html
Connecting lithium ion batteries in parallel if they don’t exactly match each other in chemical properties causes them to rapidly degrade. If you ever see lithium batteries in parallel they were most likely manufactured at the same plant at the same production line at the same day and hopefully their serial numbers are only one apart, otherwise they are quite dangerous
@@JoshinkenOhh bro ! He didn't connected batteries in parallel ! He just connected the inputs of charging module in parallel ! Each batteries are separated by a module.
@@Jatin7321 i know?
@@Jatin7321 yeah i know?
Perfect 👌
where did u find this readymade socket 😂😂😂
Only 2000 man. My phone has 5000
Можно еще провода самому отливать и изоляцию установить , и аккумуляторы тоже самому производить.
ممتاز و مميز و يشحن ٤ أجهزة فى نفس الوقت ممتاز و اتمنى ان ينتشر و اتمنى الخير الوفير الاءم و التوفيق الداءم للجميع .
Aren't those battery's dangerous?
Умничка! Литокала ли 500 отдыхает)
How are all charging at the same time?? Where connection
Give one power suply to all with some circuit for security
charging modul ko series ya perelal joda hai? kitne volt ,ampier ka chrger lagaya hai?
Nunca faça isso, essas plaquinhas usa 1 amperes de corrente, mas, as bateria precisa ser carregadas com 500mh. o ideal seria carregar 2 baterias em paralelo para cada placa de carregamento.
This depends on the specifications of the batteries.
But as you say low charging current is always good for the battery health🙂🤝
You could also simply replace the 1.2 k ohm resistor with a 2.2 k one
Estoy de acuerdo con vos, salvó que te dormiste en la espera a que se carguen!!!!
Не совсем. Это плата как раз нужна для контроля заряда, но есть 2 версии. Та что на видео, нормальная, а есть уменьшенная версия, а точнее не полноценная. Ей заряжать нельзя
@@reynaldojaviersilva4674 5ีคงืวจขขยขต
Какие все умные. Явно не понимают что 1А можно получить только с охлаждением. Потому что по мере нагрева ТР4056 она сама снижает ток. Но с этим явно никто не разбирался из комментаторов. Сосать с одного USB это как писали бред. Разве что зимой чтобы от него греться. Так же комментаторы не заметили что платки с защитой стоят. Так что максимум что ляжет контроллер который управляет поливиком. Так же если покурить документацию то можно еще пару плюшек нарыть. Но это сами. А так лучше ставить ТР5100. В таком решении она куда лучше и интересней.
You need 20V dc to operate these 4 charging module becz each take 5v 2a so running on. 5v volt charger is not a good idea
Modules are limited to 1A and the phone charger can support up to 3A. The best option is to make one with 10 battery slots and mount it on a 10A charger
Um any solutions for the heat generating from tp 4056?
2.55A de charge ou en entrée du chargeurs ? Cest module sont censé charger a 1A ??
What would happen if i connect them all to a charger
Если перепутать полярность модуль сгорит, не надёжно
Charge all battery with one power bank module
Use the powerbank module to show you the consumption and the real current
these modules get very hot during charging. The plastic around them will melt 🫠
This is very use😊 full project
Soy yo, o el hizo soldadura en el bat+ junto con la salida del mosfet protector de la batería 🤔?
Segun tengo entendido uno es para cargar la batería y el otro es para la salida hacia el aparato.
The positive output and + of the battery are factory connected and the mosfet controls the negative outputs.
I connected the type C inputs in parallel so that I could charge them with 1 charger, but otherwise each board is responsible for its own battery.
Full Video👉 ruclips.net/video/ti0IjZPfojs/видео.html
@@ErCanEverything entendido sr.
shunday platalarni qayerdan topsa boladi iltimos aytsangiz??
would'nt it be melt? as i know tp4056 can be very hot when charging
My pcbs don't heat up like you said🤔🤷♂️
Wow great❤
Какой же хороший по мощности должен быть блок питания .....
Ампер на 10 хватит спокойно учитывая что кпд этих микросхем а именно tp4056не такой уж и большой то потери на тепло большие
Зачем мощный , если они заряжаются по очереди?
@@user-yt4rt9tm7lАхахахахаха
Эти платы больше 1А на зарядку не дают , значит на 5А вполне достаточно
@@Gera.1489-110? ТР4056 в пике потребляют 1А, их там 4 штуки. 4-х амперного БП за глаза хватит! Даже если БП будет на меньший ток - это совсем не страшно. Ну, чуть медленнее будет заряжаться. Допустим не 2-3 часа, а 3 - 4 часа… 🤷♂️
Давно хотел такую.сделать, но все руки не доходили модель нарисовать
I also want to charge 4 18650 batteries with four Tp4056 modules, here are my some doubts can u please clear it😊
1,Should i connect input for modules in series or parallel
2, can i use 12v 1.5amp as input for 4 modules
You need to connect them in parallel and supply with 5V power supply. Depending on the pcs. of the batteries, you will need to use a suitable charger. Example, for 5 batteries you need a 5V 5A power supply.
Very good
Bachside all +in a row seperated all - in a row and this are conected to ? One 5v Handyloader? For 3 Tp's ?
Full video👉 ruclips.net/video/ti0IjZPfojs/видео.html
..edit. Thank You , can i use 5V/2A 🤔 it shows same in ur fullVideo but u use other Generator or Batterie ... i want use it as a Small Powerwall and of this Way i can load whit Solarpvminisystem.
You can use any phone charger.
If the maximum current of the charger is 2A it will charge 4 batteries with about 500mAh for each battery, if you put 2 batteries it will charge with 1A for each battery.
If you put 1 battery, it will still charge with 1A current
Поделил 2 ампер на все четыре и на каждую банку 500ма и при наборе полностью ёмкости каждая банка отключается и заряд идёт на оставшиеся пока все не заряд не возьмут. Но если окажется что один аккумулятор с более высоким внутренним сопротивлением он будет сажать другие. Не идеальный вариант хоть исполнение 👍
Cant read ur com.
Как сделать обозреватель за пять минут:
funny enough, i did something like this but for one battery. made out of wood and hot glue lol
2 amp is enough to all this modules? I think 1 needs 2A or am I wrong?
The modules are fixed at 1A and for this purpose they need 4A for maximum efficiency, but my charger supports up to 3A
@@ErCanEverything Nice! I gonna do this for my projects!
One module for 5V1A
it's adjustable
Hepsi aynı anda tek giriştenmi sarj oluyor
So powerbanks are actually just rechargeable batteries but glued together ? lol
Excuse me, that module can charge 9v batteries?
No.
كيفية شحن ال ٤ بطاريات ليثيوم بشاحن واحد . علما ان لا يوجد اتصال بي ال ٤ بورد شحن tp4056
Красява главное чтобы зарядка была на 💯 процентов
What is the name of the song
2 Hearts - Patrick Patrikios
ruclips.net/video/HagWuqSrr98/видео.html
Everyone just be careful 👌
Thank you🙏🙂
Can we make 4v 3amp power supply.....
Plz respond...
Моделька простая, но все же можно получить модель в формате фьюжена? F3d
یہ کہاں ملے گا بنا ھوا یا پارٹس۔۔۔کراچی میں مل سکے گا
۔۔
3d yazıcıda cıkarttınız sanırım istasyonu. en sağlamı olmuş ama.pil yataklarını sıcak silikon ile nasıl yapıştırırsan yapıştır. pil sök tak yaparken elle tuttuğum halde pil yatağı kalkıyor her seferinde. bender vidalamayı düşünüyorum 0.5cm lik suntaya.
нужно на различные штекера разъёмы входа иметь этот повр банк. например лайтнинг, мини юсб, микро юсб, тайпси..... спасибо за ролик
почему это повербанк должен быть?
18650 созданы не для этого гений блять
Было бы практичнее взять контроллеры от старых телефонных батарей
ТАК НУЖНО 4 ПРОВОДА ДЛЯ ЗАРЯДКИ ОДНОВРЕМЕННО ДЛЯ ЭТИХ МОЛУЛЕЙ ДЛЯ КАЖДОЙ БАТАРЕЙКИ .А МОЖНА НА АЛИЖКСПРЕС КУПИТЬ МОДУЛЬ ЧТО ЩАРЯДАЕТ ОДНОВРЕМЕННО ВСЕ 4 БАТАРЕЙКИ И НЕ БУДЕТ ГРЕТТСЯ
I didn't say it was warming up.
Viewers, they say that and at this charger everything is fine.
модули паралельно на входе питания соединены. зарядник линейный, вот и греется. чем больше ток и разность напряжения, тем больше нагрев.
Stl?
Creative video, thanks :) 👍
какая схема подключения?
Есть многоканальные зарядные устройства . Зачем так извращатся ?
How to found this making material
I have now added the link to the long video below and its description has it all.
i added 4 cells to one board and it seems to be working. am i right in doing that? complete novice just messing around see what i can do lol
It will be a problem if the individual cells are not balanced (are at different voltages). There is a tutorial that explains why it's good to use one module for each cell.
And that's how you manage to burn your usb cable
Meu amigo a onde vende estes suportes de bateria vc teria o lik
I want one, how much?
я не понял принцип работы,как они все сразу заряжаются?
The positive and negative terminals are joined together underneath the pcbs
он соединил в параллель , но не учел то что , максимальный ток который может переварить проверил
*провод
@@user-yq4zq4ph6c но на видео он не показал что запаял их в паралель
Я так понял, что он запаралеллил входы плат заряда, а не выходы, иначе сами платы сдохли бы. Лучше питать сами платы от одного источника, чем кучу АКБ от одной платы. Во всяком случае я так сделал.
Liitokala : widzisz mnie ?
Haha. Wo gibt's den Bausatz ?
not worth for me, XTAR chargers cost 15 dollars with 4 slots, LCD screen and some options like storage, test, charge, discharge, are more saver and you can put there all sizes of li-ion cells like 21700 and 26650 big ones, buying the tp4056 for 1 dollar is just waste of money
make to a Flash charge , like super fast charging
Ore board 5 bettari 3.7 use oru video podunka