Dewalt Power Washer Repair, No Pressure? No Problem - 5 minute fix!
HTML-код
- Опубликовано: 23 авг 2024
- This video will show you how to make a quick 5 minute repair that will cost ZERO dollars to most power washers on the market. This one is the Dewalt 3025 3,000psi 2.5gpm pump.
If it was helpful, please give me a thumbs up and subscribe to channel.
Dude, it's been sitting for 3 years and your vidio is up for 6. You the man!!
Whoa! This fixed my machine 😂 I was pulling into Home Depot to get it serviced. I saw this video and thought why not try it. And boom it’s fixed!!!!! You’re the man!!!!
@@vi8ezmusicgroup thanks!
I wish I would have seen this sooner, might have saved me a few hours of frustration. I can’t thank you enough. FYI for others, my pin wasn’t stuck but taking it apart and reassembling it seemed to do the trick.
I have a 3400 Dewalt bought it last year used it once tried starting yesterday it would run for a min and backfire. i took carb all apart checked jet it was clean. Did a youtube search found you. Mine was just the opposite, factory setting screwed down to tight over pressuring pump & motor, took valve apart it was operating fine. left adjustment about where yours was, ran fine....thanks for taking the time
I can use this. I also liked it when your dog stepped in for a nod.
Super helpful, this solved my "no pressure" problem on 3600 psi DeWalt, I didn't have to remove the pin, just tap it to loosen and worked great again. Thanks!
@@user-yn4tb1jj4z awesome!
Thank you SO MUCH-fixed me right up. Laughing because my husband threw up his hands, but via your video instructions I got it going again!
You’re welcome!
dude, this worked. Awesome, took me about seven minutes, and I have full pressure again! I did exactly what you told me to do! I knew some wise person on RUclips would have the answer!
7 year old video, and it just saved me. Thank you!
Thank you SOOOOOO much ….I have a Dwalt 3400 PSI , only used it may be 7-8 times, and today I got ready to power wash my side walk and driveway, it had no pressure, I am so glad I went online and after watching 4 videos, yours was the most relevant one that gave me the answer and it saved me at least $180 (according to the repair shop) , thank you so much again, you are a great blessing.
Having this exact issue. Great video. Good close up on what you were doing. Easy to follow. I wish all RUclips fixit tutorials were like this
Thanks for the kind words!
I was ready to junk mine until I saw your video. Works great. 10 minutes to find the tools and 5 minutes to fix. Thank you
Your an idiot if you junked a dewalt pressure washer guy
Thank you so much! I didn't even take it apart. After watching this I just sprayed it with WD-40 then tapped it with a hammer and whala making pressure! Thank you!
Thank you!!!! You saved me hours of time, and possibly the expense of buying a new power washer.
@@keithhafer I’m glad my video helped you out!
OMG, I'm watching this with the audio off, but your Dewalt looks like it has the same pump as my SIMPSON, and now I know EXACTLY how to get at my unloader! You rock.
The look
M
One
L
I’m l
I l
M I’m
M ok LN. Mmm l
M
M
Mom m m
Mmm
K
C m onI
B
I have a 3425 Dewalt Pressure washer about 3 years old this spring season. Started right up but no pressure. After checking user serviceable items I found your video, followed the directions and I'm back in business. Although I winterize my unit every year and it's garage stored I still encountered this issue. Thanks for the video.
5 min fix but have to watch 10 min video. Now a fifteen minute fix 😂.
But anyway jokes aside, thanks worked a charm 👍
Thank you so much. I was so frustrated and now it’s up and running again. You’re a life saver
Thank you so much! Just got a pressure washer for $200 because buddy said the pump was not working . Free fix! Pressure washer at 20% the price!
Thanks, and also check the filter that is in the first Hose
This is a great post!! This is the second year we had to watch your video and fix the pressure washer again. Worked out great!! thank you so much!!
I’m glad I could help!
Thank you for this video! Just saved me $395 from repairman claiming I needed a whole new pump!
Thank you! This totally fixed our Dewalt 3000 psi pressure washer. Exact problem. Keep it up!
Its a very easy and cheap fix that I needed to share with everyone. I hate when I or anyone gets ripped off on bogus repairs.
Excellent, such an easy fix and less than five minutes. Thank you!
Did the same and works great. Thank you sir you are a life saver ❤. God bless you
Thank you!! I hope this fixes my lack of pressure. Love your dog. From NE WA.
Fixed my water flow issue right up. FYI the small nut on the stem is a 10mm and the big nut is a 7/8. Thank you much for your video
Not all heroes wear capes. Thanks for the video sir! Glad I stumbled upon it. Now I know what to do just in case. I got the 3300psi
Thank you for posting this video! I was about to buy a new $275 pump. This was the fox for my pump problem!!
Thanks 🙏🏽 brothers saved me some money blessings to you an your loved ones
Dewalt 3400 PSI ... His solution work perfectly!
Thank you Billy I'm going to check my pressure washer out now
Hi Billy.
Well, I checked it and as you said the offloader was stuck. cleaned it up put it back together but unfortunately still no joy. Going to try (may part are obsoleted) and get a valve replacement kit, a new off loader (just in case) and see what happens. Anyway, thank for the great tip!
I really appreciate the video. My 3200 quit having pressure yesterday and I about lost my mind, since it was practically brand new. Was afraid it could have been something expensive.
Absolutely an easy fix! Appreciate you taking the time to do this for whomever. Mine is a 3400 psi but same process. And it works. Thank you Sir!
Excellent video. Just finished the fix on my Dewalt 3400 PSI pressure washer.
I have the Dewalt ( Simpson ) 4400,
The other thing to check is the valves, they crack after a while, I've done 100s of homes, a 25,558 sq ft Beach front hotel in 6 hours and have a 75,000+ sq ft hotel lined up with my Dewalt 4400, it lost pressure but my problem was the center valve, the plastic housing that holds everything inside cracked. It was hard to notice.
Easy $70.00 fix in 10 minutes.
UPDATE:1 year and still cranks within the first 2-3 pulls. Probably will buy another when this one finally does bite the dust ruclips.net/user/postUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX . No issues at all. Very happy with it.UPDATE: After 6 months of use and over 70 uses I would still highly recommend this pressure washer. It does vibrate a decent amount but never had it “walk” like others have mentioned. No oil leaks, still seems to run like the day I bought it. Still cranks within 2-3 pulls every time. Very happy with my purchase!Have used it about a dozen times now. Plenty of power, cranks up on 1-2 pulls every time. My only complaint would be I wish it was a little taller to make it easier to walk with it (hits my ankles a lot) and that the two hose connections were a little further apart but it hasn’t caused me any issues. Seems to run a good 1-1/2-2 hrs on a full tank, overall a well built machine and definitely worth the money in my opinion.
Mine is no pressure out of the box. I either have to wrench on it brand new or I need to get the gas out of it to return, think I will leave the oil in it.
Thanks you just saved me time and money, took me about 10 minutes and it’s fixed 👍
My DeWalt has absolutely no pressure and it's been driving me crazy the same scenario I haven't used it in a while so maybe it's the same problem nice video thanks for the help
I think putting some anti seize compound on the valve before reinstalling may help with seizing up issues
thank you friend , I have a back & decker 2600psi had the same problem !!! hugs from Brazil
So glad I watched, can't wait to try it.
Hey man a big thank you from down here in New Zealand. I thought my fairly new waterblaster had crapped out completely which was a real inconvenience at this time of the year. (its summer here). But i had a look on you tube for a repair and found your video and for the first time ever it all worked exactly as you said. Was an easy fix and its going fine. Thanks for your effort.
This is exactly what my problem was. Thanks for the help!!!!
Great video, thanks for the help! Worked like a charm!
Very helpful! I'm having pressure issues and I can't figure out why. Now I know! Gonna fix it right now! 👍🏾
Worked like magic on the 3400 too, but I didn't have to mess with the micro Allen nut
How did you get the stem out? I have a 3400 too and I can't figure it out.
How did you fix it
After watching this video I worked on my pressure washer. I did everything shown (except the end nut wouldn't come off so I could not get the spring off). I was able to get the unloader out and the pin was not stuck. It would move up and down. I put it back together and put water to it and it still did not create pressure. I took it off again then took off the other valves to the left of the unloader including the one on top. (I had the hose connected looking to see if there was a full flow of water at the rate of water flow through the hose. It took a little maneuvering and work to get a flow of water from the opening for the unloader but it finally came. There was restricted flow to the left of the unloader so I knew it was something on that side.) Long story short, I took all the valves off and sprayed a little penetrating oil in them. Put them all back on, started the motor, and turned let it run for about 15-20 seconds with the water turned on and whatever was stuck inside broke free and I had pressure. Thanks for the help.
Wow, I'm glad I came across your comment. Thank you so much.
Great job. Going to try it and if it works I'll let you know. This video is about 6yr old and so is my washer.
Thanks Billy.
There is a pump preservative fluid that can be used when put away for the winter. Briggs and Stratton makes it. Check Amazon.
Thank you sir thank you very much had it at work and same problem bit the other guy I work with is a fake mechanic. Went bought brand-new one cause said it s broken but it's not anymore thank you again
Thanks Billy. Repair shops for these will be quite upset that you've revealed one of their big money-makers. Since DeWalt only gives a 2-year warranty on a part that mfgr (AAA) offers 5-year is not impressive. But next pump for my 3800 will be from CAT anyway...
One comment on your procedure: I believe you should only remove the allen-head screw then back the entire unloader assembly out using nut that is against the pump body, but DO NOT touch the outermost nut that sets the spring pressure and resultant overpressure limit. Getting the later wrong could blow seals (if too high) or reduce operating pressure (too low).
haha o shops are going to be upset
Awesome video! Worked on my 3600 dewalt pressure washer also!
Thank you so much. I was about to pay to fix mine, and your video fixed it right up!
Great video it worked for a 3400 PSI , when we took everything apart it looked like the parts where like new but it had no water pressure, whe we put everything back it started working
How did you guys fix your model I have the same one no water is coming through at all no pressure..
@Mr. Suber, we followed the video instructions to take it apart but the key is what the guy did in the minute 4:10 you gotta make sure that little pin is moving as he shows , no new parts needed .
So nice to find a good video about a certain subject on RUclips, informative and clear information. Thanks much again.
Great video brother. Perfect fix!! Worked like a charm on my DeWalt 3400! 🤙🏼🤙🏼
Thanks for your great video Bill, I will fix the same problem that you have showing on the video.
Great video. Was about to take to the shop when I decided to check ole RUclips. Low and behold you were dead on right! Saved me money! Thanks
Thanks, Billy! Gettin' My pressure washer adjusted to get to work. You da Man! :-)
Worked great. Saved me time and money.
Thanks for getting right to the point and showing the RUclips community a quick easy solution. Oh, and not asking me to smash/pound/crush the like button.
Thanks!
Thanks. It got my pressure washer working again.
Gotta love RUclips! Thanks. Great solution.
Me and my husband started our own business and this video really help us at 2 am 🕑 😅 and you saves us a headache 🤕 thank you for your time
what if that spring IS working?? then what would the next thing to look for?
Boom! You saved another. Thank you.
Thanks alot!! BTW it's a 3mm Allen on the 3400 model anyway for anyone wondering
Mine is completely seized up. Tried 3mm and it stripped it out. Did you have any issues?
@@keiths585 ouch!! Sucks once any Allen head is stripped but you can try soaking in creeping oil overnight then take a slightly oversized flat headed screw driver and hammer it into the stripped out socket head
Thank you for sharing your videos and knowledge. Fix mine I was going to send it out.
great video. I've used it each of the past 3 years!
Thank you for that video! That was the problem!
Thx for the tip I appreciate it I’ll try check that on my pressure machine
Thank's I have the same Pressure washer worked great
Very good teacher
nice vid bud ...i fixed 2 pressure washers after seeing this ...thankyou
Your the Man I appreciate the video it saved me a lot of Money
Great job, I'll be trying this tomorrow!
Thank you very much sir I fix my own pressure washer because you did a good video
Husband did it but just skip the part where you took the entire thing apart to leave the factory study and just did your last step of unbolting from the main part and then getting the pin to move and put back in so we did not mess with the factory setting of the pressure so in less steps you can accomplish the same thing
I guess it is kinda off topic but do anyone know of a good website to watch newly released series online?
@Archer Kayson i use flixzone. Just google for it =)
@Lyric Ishaan Yea, have been using flixzone for months myself =)
@Lyric Ishaan thanks, signed up and it seems like a nice service :) Appreciate it !!
@Archer Kayson Glad I could help :)
I found that if you just tap it while still attached that works also
its not under warranty. they call it a ware and tare part. mechanic has mine now (the 3400psi model) and is about to hit me with a bill for $120 to replace the valve. going to ask for the ild valve back now so i can see if that was my issue. my washer stopped giving amy preasure amd after a few taps to the pump i got half pressure with a choppy flow. worked fine to wash my house then an hour later i started it up at my fathers to clean his siding and thats when i started having issues. thanks for the info, good to know.
Thank you ,for the video ,now I know how to fix mine 👍🏻👍🏻👏🏻
It works greats and easy to do. Thank you
Nice video sir. I have the 3300, huge regret buying this junk. Had many problems out the box. Soap reservoir tank leaking from the seam, as its not made of one piece lol. First time i used it the trigger pin got jammed. Now no pressue and the soap reservoir fills with water and blows the cap off... all this crap and the machine is new with under an hour total usuage 🗑 🚮
Thank you! You solved our problem!!
As we all know city water sucks . So if your going to store your unit over 30 days try using a product made by Black/Decker pressure washer pump lube , I think about $8.00 at Lowe’s but will save you a lot of headache and each can will give you multiple uses. I got some after I had to have my pump rebuilt and now 3 years later no issues at all.
Thank you very much man!!!!! You just saved me a ton of money!!!
Thank you.
Man i was having the same issue got it brand new im about to see if this is the problem and any tips on gas and mixing i cab use for gas
Thank you this is exactly what was wrong with mine
Thing is brand new with only like 10hrs run time
Thank you!
Thank you 🙏 sir for your video you save me a few dollars.
Thanks dude! I'm back to work.
Thank you, Billy!😀👍
Maybe you can help. I have a 3300 psi dewalt pressure washer (hose connects under neath the back side, not the style you have) how do you adjust these unloader valves? I’m trying to run a ball valve setup and it’s not drawing pressure on my valve setup. But if I kink the line it will build pressure. So I’m assuming I need to adjust the unloader but I’m not quite sure how, most commercial washers have a black handle that you adjust with but this one doesn’t. Maybe you can help?
I have a 3400 PSI model and my unloader has plastic cover which is used for adjusting amount of pressure. Does anyone know how to remove it?
Just bought one from a neighbor for 20 bucks at a garage sale. Haven't tinkered with it just yet..
I have same pressure washer, any ideas where I can buy this replacement part, because mine still not working after all this. Thanks