Amazing work & thumbs-up .. Your channel deserves a ton more views .. A true Master at work & a Credit of a man for the entire PS3 community .. Many thanks
As I've been watching your videos for a while, and I've seen you fix this issue multiple times, I think I've understood your diagnostic process. Symptom: PS3 shows red light that turns to green, but then the system either immediately loses power or loses it after a second. Diagnosis: it's all about ruling out components, that is, figuring out what is NOT causing the issue. 1 you test whether or not the power supply is causing the issue. So, you swap the PS3's own power supply to a different PS3's power supply. There are two possibilities: either the PS3 will now turn on or nothing changes. If it turns on, the fault must be in the power supply, because it's the only component that was changed. However, of the system doesn't turn on, then you know that the power supply is not causing the issue (or at least it's not the only cause). 2 The PS3 is powered by 12 "mini" power supplies on the motherboard. These mini power supplies only work at certain voltages, so if the voltage is incorrect, the PS3 will protect itself by shutting itself down. The mini power supplies are regulated by resistors. If there is an incorrect voltage it's caused by a resistor that doesn't output correct voltage. 3. You need to test which out of the 12 power supplies is not outputting the correct voltage. You can test it by measuring the resistance values of their resistors. 4 Once you've found a resistor that has an incorrect output value, you need to replace it by a resistor that will output the correct value. Now, you only need to do the final test: does the PS3 turn on? If it does, the issue was indeed caused by the resistor, if not, then there's probably another fault that needs to be found and fixed. P.S. If your PS3 stays on for 30 seconds before it shuts down, it's likely that the fault is caused by something other than one of the resistors in question.
Thank you for sharing Master Jedi of electronic repair. Better improvement video, Great job! The subtitles of what you are doing help a lot, providing the value of each resistor and detail by detail until the problem was fixed.
idrees am a new subscriber to your channel from algeria . love your vids and i want to say u are a respected man and a good teatcher . and if i can ask about a tutorial vid about the e3 flasher i bought one but still yet to use it not having time and i dont know how to do it properly
The second one out of the three present resistors (with two unpopulated spots to separate them all, so the middle one) below the south bridge is reading 0 ohm. The first is 48 ohm and the third is 32.8 Are these values correct?
@idreestech Sorry, I was being stupid. The resistor that measured 0 Ohm is actually at 4.5 KOhm, forgot to set my multimeter correctly. Is this normal? I removed the cmos battery since it was dead.
Hallo sir,you are genius !!! I also have exactly the same problem in my ps3 super slim. Kindly suggest what I should do. Sir it will be a great boon for all of your followers and viewers if you please share values of all ps3 variants resistors and power rails.please also make a video about explaining which section of ps3 motherboard is responsible for what thing.it will be a great help for all of us. Thanks a lot.
The king returns nice video you are so underated keep them coming
Appreciate it
Amazing work & thumbs-up .. Your channel deserves a ton more views .. A true Master at work & a Credit of a man for the entire PS3 community .. Many thanks
Thank you so much 😀
As I've been watching your videos for a while, and I've seen you fix this issue multiple times, I think I've understood your diagnostic process.
Symptom: PS3 shows red light that turns to green, but then the system either immediately loses power or loses it after a second.
Diagnosis: it's all about ruling out components, that is, figuring out what is NOT causing the issue.
1 you test whether or not the power supply is causing the issue. So, you swap the PS3's own power supply to a different PS3's power supply. There are two possibilities: either the PS3 will now turn on or nothing changes. If it turns on, the fault must be in the power supply, because it's the only component that was changed.
However, of the system doesn't turn on, then you know that the power supply is not causing the issue (or at least it's not the only cause).
2 The PS3 is powered by 12 "mini" power supplies on the motherboard. These mini power supplies only work at certain voltages, so if the voltage is incorrect, the PS3 will protect itself by shutting itself down.
The mini power supplies are regulated by resistors. If there is an incorrect voltage it's caused by a resistor that doesn't output correct voltage.
3. You need to test which out of the 12 power supplies is not outputting the correct voltage. You can test it by measuring the resistance values of their resistors.
4 Once you've found a resistor that has an incorrect output value, you need to replace it by a resistor that will output the correct value. Now, you only need to do the final test: does the PS3 turn on? If it does, the issue was indeed caused by the resistor, if not, then there's probably another fault that needs to be found and fixed.
P.S. If your PS3 stays on for 30 seconds before it shuts down, it's likely that the fault is caused by something other than one of the resistors in question.
WOW! Incredible...
Thank you so much sir, you are the master and you deserve a five star
Wow, thanks
Thank you for sharing Master Jedi of electronic repair. Better improvement video, Great job! The subtitles of what you are doing help a lot, providing the value of each resistor and detail by detail until the problem was fixed.
Thank you very much!
👌👌 EXCELLENT VIDEO!!! Subtitles helped alot 🙏🏽
Glad to hear that!
Really Really good video again the way of identification of problems are unique N show your experience 👍
Thanks a ton
idrees am a new subscriber to your channel from algeria . love your vids and i want to say u are a respected man and a good teatcher . and if i can ask about a tutorial vid about the e3 flasher i bought one but still yet to use it not having time and i dont know how to do it properly
Thanks for the sub! In any of my videos, you can find its use.
ما شاء الله / شكرا لك اخ ادريس / ربنا يجعل عملك في ميزان حسناتك / تعلمت منك الكثير / اخوك حامد من فلسطين
Very poor used of camera. Your video would have been one of the best but no visible.
Sorry for that dear.
Nice job. What's the value of the resistor replaced?
it shows 247k ohms, not the actual value but it shows like that You have to find it out yourself.
Mashallah acha kaam karty ho ap really appreciate your Work
Wow cheers!
amazing video as usual plz continue ,, and plz brother when can u make a video about how to use the oscilscope
As soon as possible
My master please continue your good work and do I need an oscillator to check the power rails?
An oscilloscope.
@@idreestech yes sorry that’s what I meant to say
The second one out of the three present resistors (with two unpopulated spots to separate them all, so the middle one) below the south bridge is reading 0 ohm.
The first is 48 ohm and the third is 32.8
Are these values correct?
Please check the reading after separating the battery cell. I hope this helps!
@idreestech
Sorry, I was being stupid. The resistor that measured 0 Ohm is actually at 4.5 KOhm, forgot to set my multimeter correctly. Is this normal?
I removed the cmos battery since it was dead.
Yes, it is normal.
Great job stay blessed for ever
Thanks for the video... great job. plese make more
Thank you, I will
Brother from which country you are ??
Pakistan ??
Reply plzzz ?
Lahore Pakistan.
Hallo sir,you are genius !!! I also have exactly the same problem in my ps3 super slim. Kindly suggest what I should do. Sir it will be a great boon for all of your followers and viewers if you please share values of all ps3 variants resistors and power rails.please also make a video about explaining which section of ps3 motherboard is responsible for what thing.it will be a great help for all of us. Thanks a lot.
Watch my new video
genius. could u make a video on fixing 8002F1F9 problem on ps3 slim while updating bluetooth chip?
Sure I will.
My humble request, please explain for us all the power rails and resistor values of both ps3 and ps4 motherboards. Thanks in advance be blessed
Noted
Nice video
Thanks
Sir which smd testor is used ?
It is an ordinary SMD tester dear.
ويا ريت ترجمة للغة العربية اذا امكن / واذا لا تسطيع الترجمة لا يهم / وربنا يوفقك
اه ، احمر الخدود في حضن كبير.