After several attempts at dialing in the modulator I believe I got it where it needs to be. The gold standard, in my opinion, is the shift smoothness of the Turbo Hydramatic 400 (TH400) in my Coupe Deville. (chosen for certain models of Rolls Royce cars as well mind you) The 722.3 in this 300SD now shifts quite smoothly and is not distracting like it was before. Even the 3to4 shift is now smooth. I've not encountered any flairing..... what ever that is. The end result was that I turned the adjustment all the way counter (anti) clockwise until it stopped, then a half turn back clock wise. (7.5 turns from where ever it was out of the box) I made several adjustments in either 2 or 3 turns at a time before each test drive. Note also that I started these adjustments with a new unit right out of the box. I have no way of knowing the position in which the manufacturer places the adjustment before they package it for sale.
I will definitely be doing this next. I believe I have adjusted all I can with vcv and current modulator. My shifts are close to what you were experiencing before you changed the part. All vacuum related
This modulator allows for fine tuning adjustments. Couple that with adjustments made to the Bowden cable, and yes. There is a high degree of adjustment available and simple replacement alone is just the first step.
Great vid. I have a w124 with the same modulator, and I think mine's fine cause it can be adjusted with the T-pin to impact shift smoothness. However, I have one peculiar symptom. When I cause the car to shift between 2000-2200 rpm, there is a noticeable flare. If I am gentle with throttle and it shifts below 2000 rpm, no flare. Same with full throttle when it shifts upwards of 2500 rpm, no flare. What could possibly be the reason for this you reckon? Slight tranny oil leak exists, but dipstick has been showing full for atleast an year.
From what I understand, the situation you are describing is quite common. Long story short I believe it has to do with the amount of vacuum supplied to the modulator by the VCV (Vacuum Control Valve) under these part throttle conditions. Here is a document detailing the modification of the VCV to help with this situation. I've not done it however. jenniskens.livedsl.nl/Technical/Tips/Files/Mercedes%20722.4%20adjustment%20guide.pdf
@@ImpalamansGarage This article was awesome but I failed to mention, mine's on petrol, not a diesel. I read most of it thinking maybe some parts will overlap but feels like on diesel, the vacuum system is completely different.
Can the valve be removed when the transmission is still filled with ATF, or will the fluid start draining from this opening the moment I pull the valve out? Shifting is working fine but there is wetness in that area. I suspect that o ring to leak.
Thank you for your great videos. I have a 1991 350SD, I lost reverse gear and started looking for a used transmission but after not finding one I decided to replace my vacuum modulator using your video as reference and to my surprise , I now have reverse but is not smooth, it doesn't kick in until 4 or 5 seconds later and makes my tires spin. How do I know which way to adjust the modulator? I also found a disconnected vacuum hose from the vacuum control valve that runs next to the fuse box but I don't know what it connects to. Any advice will be much appreciated , thanks again..
Clockwise adjustments of the modulator increase shift firmness. Counter clockwise adjustments make them smoother. Going too far either way has obvious repercussions. I'm not sure adjustments to the modulator will address the reverse issue. Here are a couple of links with good discussion on this topic that may help. Regarding Modulator adjustments: www.benzworld.org/threads/i-fixed-my-shift-flair.1314697/#post-2330736 Regarding reverse issues: www.peachparts.com/shopforum/diesel-discussion/376603-only-using-half-springs-722-3-transmission-reverse-piston.html
Here's a vacuum diagram of an OM603 from 1987. It may suffice to help you. www.peachparts.com/shopforum/attachments/diesel-discussion/98874d1326765510-om603-vacuum-parts-vacuum603.jpg
I have E320 with 722.5 transmission, it only gears first gear and don't change it. Do you think that modulator valve is my problem? What you indicates me how start the diagnosis?
The modulator valve only controls the quality of the shifts. You could remove it entirely from a normal transmission and it would still shift through all of the gears but each shift would be very harsh. There does seem to be a lot of discussion on your problem in the Mercedes forums. www.benzworld.org/threads/722-5-transmission-shift-problem.1549876/
No sir. It will not. First: Check your fluid. If it all leaked out, then the trans won't do anything. Second: Check your shifter linkage under the car. It may have become disconnected. If it's full of fluid and your shifter linkage is OK then you need to tow it to a transmission shop. If all the fluid leaked out you will need to refill it. Remember that checking trans fluid is done with the engine running at idle and trans in park. Each time you add fluid to the system you should hold your foot on the brake with the engine running and cycle the shifter through all of the gears and then back to park. Check again. Add fluid if needed. Cycle through gears again, etc.....
Several annoying issues: Shifts from 1 to 2 and 3 to 4 were hard as nails. Shift from 2 to 3 was way too soon. Also the original modulator has a rubber cap on it that is prone to leaking vacuum. The new modulator is an improved design. Mercedes is not the only car manufacturer that uses vacuum modulators to control shifts. This is an extremely common maintenance item for older auto trans cars.
Here is the modulator valve for your car. It should not be difficult. www.pelicanparts.com/More_Info/1262709179.htm?pn=126-270-91-79-M22&SVSVSI=3760&DID=13332
I've got a 1986 560SL with 200K miles that shifts smoothly while driving. Its also a 722.3 transmission. The problem is when I shift to or from Park/Neutral/Drive to Reverse I get a hard engage. I can get a softer engage if I momentarily shift to Reverse, quickly back, then back to Reverse. The Modulator looks original. Have not checked the Modulator to see if it holds Vacuum - need to, but was concerned about loosing my Transmission fluid. Do you think I need to try a new Modulator?
You'll note very early in the video where I show the open port where the modulator resides that there is no transmission fluid which had dripped down over the lip of the pan. It's dry. Thus there is no fluid loss when removing it. If your transmission shifts properly and the only thing wrong is a hard reverse engage then I would say your modulator is not the issue. Without knowing what you consider to be a "hard engage" into reverse, it's tough to say where the problem may reside, however there is a fair amount of discussion on this topic. Here is one example: www.peachparts.com/shopforum/diesel-discussion/376603-only-using-half-springs-722-3-transmission-reverse-piston.html Your issue may be related to the reverse clutches or springs insde the transmission. I would start with the basics however. Does you fluid look good? If it's not red, change it and the filter. Check all vacuum lines.
@@ImpalamansGarage Transmission fluid is bright red and full to correct level. I can get a much less "thunk" by teasing it quickly into reverse, back out, and back in. Wondering if its vacuum. Can the way the Modulator is adjusted have an impact on this "thunk"?
@@cwmoser I highly doubt it is vacuum. The modulator, whether or it's bad or good, should have no effect on the engagement of reverse gear. The modulator regulates fluid pressure to control firmness of upshifts. I would just hold my foot on the brake and shift it into reverse and wait until it's properly engaged before reversing. I fear moving the shifter around like that might do more harm than good.
Hello, I have some problem with shifting from my European 1983 w126 380. It shifts true the gears very fast, when I drive 40/45 kmh it’s already in last gear.. when I press the gas pedal driving 50 kmh there is no shift back, this only happens when I press the kickdown. Than as you press it the car wil drop 1 or 2 gears and brings a smile on my face.. But as soon as I release the “kickdown button” with the gas pedal it wil shift back to last gear. Now I don’t know if this is normal or there is something wrong here.. Next problem.. when I floor it from stand still, it wil shift first to second smooth, around 5000 rpm maybe 4800rpm. Not sure. than the 3rd to 4th I need to let the pedal come up (release the “kickdown button with the pedal) because it wil go past 5500 rpm and feels like it won’t shift 🤷🏼♂️ Is this supposed to be like this or is there something wrong here to..
You may need to adjust the bowden cable. On my car a clockwise adjustment makes the transmission shift sooner. Counter (anti) clockwise makes the transmission shift later. Do this 1/2 turn at a time and test drive after each adjustment. The bowden cable adjustment determines WHEN the transmission shifts. The QUALITY (how hard or soft) the shifts are is determined by the adjustment of the vacuum modulator on the transmission. A clockwise adjustment of the vacuum modulator will make the transmission shift harder. A counter (anti) clockwise adjustment will make the transmission shift more softly. Both the modulator and bowden cable work in concert with one another. It will take you a while to make the adjustments and get your transmission shifting properly. The Mercedes factory set these adjustments by measuring transmission fluid pressures during the manufacturing process. Lastly, when the transmission is shifting from 3rd to 4th under a heavy throttle condition, you may find it necessary to let up (decrease throttle pressure) to make it shift. In general, under wide open throttle you want the transmission to shift at the shift points noted on the speedometer. There are marks on the speedometer showing about where the car should shift when you floor it.
Here is an excellent document on how to adjust your Mercedes transmission. This document is for a diesel but it may be of help. jenniskens.livedsl.nl/Technical/Tips/Files/Mercedes%20722.4%20adjustment%20guide.pdf
Yes. The adjustability of this new version of the modulator is nice. Keep in mind the quality of shifts is dictated by the modulator and the timing of the shifts is regulated by the Bowden cable adjustment. They work together so you will need to tweak both of them.
The transmission shifts so much better than before. With the updated modulator and adjustments plus new vacuum lines in several areas.... the driving experience is very nice. In some instances, depending on the driving conditions I have noticed a very slight flare from 2 to 3 but this has only happened once or twice. Debating on whether or not to make another small adjustment. Guess I will just have to drive my classic Mercedes some more to determine!
@@ImpalamansGarage Once you put that plastic cap on, can you remove it? I have a new injection pump with bigger elements. The car shifts great except for the 2-1 down shift is rough. I used the fine adjustment and the shift improved slightly. If I could just get that cap off and adjust it more I believe the problem will be solved.
Sounds like you've got some troubleshooting to do. Even if the modulator was not working at all, I think your transmission would still shift. I would start with the Bowden Cable. Have you tried adjusting it? Trying screwing the Bowden Cable clockwise (inward) for several turns and see if that has an effect. You are saying your transmission stays in 1st gear no matter what ?
@@joshuapena1314 Have you confirmed that your shift linkage under the car is connected properly? If it is connected properly it sounds like a transmission rebuild is needed.
Impalaman's Garage that’s the first thing o checked and both bushings were missing so I replaced both of the i even went ahead and bought a brand new shifter but still no luck I also flushed transmission fluid out and replaced the filter, Jesus sounds like it’s gonna be an expensive fix
Might be a better option to find a good used one that you know is good to go. Install it. Then buy a rebuild kit for the old one and learn to rebuild one at home.
After several attempts at dialing in the modulator I believe I got it where it needs to be. The gold standard, in my opinion, is the shift smoothness of the Turbo Hydramatic 400 (TH400) in my Coupe Deville. (chosen for certain models of Rolls Royce cars as well mind you) The 722.3 in this 300SD now shifts quite smoothly and is not distracting like it was before. Even the 3to4 shift is now smooth. I've not encountered any flairing..... what ever that is. The end result was that I turned the adjustment all the way counter (anti) clockwise until it stopped, then a half turn back clock wise. (7.5 turns from where ever it was out of the box) I made several adjustments in either 2 or 3 turns at a time before each test drive. Note also that I started these adjustments with a new unit right out of the box. I have no way of knowing the position in which the manufacturer places the adjustment before they package it for sale.
Did it solve your late shift?
Good video. Thanks for being so detailed about the adjustments
I will definitely be doing this next. I believe I have adjusted all I can with vcv and current modulator. My shifts are close to what you were experiencing before you changed the part. All vacuum related
You are the best ever
So important question, did this fix all of your shifts??
This modulator allows for fine tuning adjustments. Couple that with adjustments made to the Bowden cable, and yes. There is a high degree of adjustment available and simple replacement alone is just the first step.
Dumb question, Do you turn it right to make the shifts smoother or harder?
Clockwise adjustments of the modulator increase shift firmness. Counter clockwise adjustments make them smoother.
Great vid. I have a w124 with the same modulator, and I think mine's fine cause it can be adjusted with the T-pin to impact shift smoothness. However, I have one peculiar symptom. When I cause the car to shift between 2000-2200 rpm, there is a noticeable flare. If I am gentle with throttle and it shifts below 2000 rpm, no flare. Same with full throttle when it shifts upwards of 2500 rpm, no flare. What could possibly be the reason for this you reckon? Slight tranny oil leak exists, but dipstick has been showing full for atleast an year.
From what I understand, the situation you are describing is quite common. Long story short I believe it has to do with the amount of vacuum supplied to the modulator by the VCV (Vacuum Control Valve) under these part throttle conditions. Here is a document detailing the modification of the VCV to help with this situation. I've not done it however. jenniskens.livedsl.nl/Technical/Tips/Files/Mercedes%20722.4%20adjustment%20guide.pdf
@@ImpalamansGarage This article was awesome but I failed to mention, mine's on petrol, not a diesel. I read most of it thinking maybe some parts will overlap but feels like on diesel, the vacuum system is completely different.
Can the valve be removed when the transmission is still filled with ATF, or will the fluid start draining from this opening the moment I pull the valve out?
Shifting is working fine but there is wetness in that area. I suspect that o ring to leak.
No need to drain the ATF to remove the modulator.
@@ImpalamansGarage Thank you!
Thank you for your great videos. I have a 1991 350SD, I lost reverse gear and started looking for a used transmission but after not finding one I decided to replace my vacuum modulator using your video as reference and to my surprise , I now have reverse but is not smooth, it doesn't kick in until 4 or 5 seconds later and makes my tires spin. How do I know which way to adjust the modulator? I also found a disconnected vacuum hose from the vacuum control valve that runs next to the fuse box but I don't know what it connects to. Any advice will be much appreciated , thanks again..
Clockwise adjustments of the modulator increase shift firmness. Counter clockwise adjustments make them smoother. Going too far either way has obvious repercussions. I'm not sure adjustments to the modulator will address the reverse issue. Here are a couple of links with good discussion on this topic that may help. Regarding Modulator adjustments: www.benzworld.org/threads/i-fixed-my-shift-flair.1314697/#post-2330736 Regarding reverse issues: www.peachparts.com/shopforum/diesel-discussion/376603-only-using-half-springs-722-3-transmission-reverse-piston.html
@@ImpalamansGarage I will try the adjustment tomorrow and will also check the other info. thank you for your time and knowledge.
Here's a vacuum diagram of an OM603 from 1987. It may suffice to help you. www.peachparts.com/shopforum/attachments/diesel-discussion/98874d1326765510-om603-vacuum-parts-vacuum603.jpg
I have E320 with 722.5 transmission, it only gears first gear and don't change it. Do you think that modulator valve is my problem? What you indicates me how start the diagnosis?
The modulator valve only controls the quality of the shifts. You could remove it entirely from a normal transmission and it would still shift through all of the gears but each shift would be very harsh. There does seem to be a lot of discussion on your problem in the Mercedes forums. www.benzworld.org/threads/722-5-transmission-shift-problem.1549876/
Hello I own a 1982 300sd 126, my transmission won’t engage into any gears it stays in park any clue if changing the vacuum modulator would fix this?
No sir. It will not. First: Check your fluid. If it all leaked out, then the trans won't do anything. Second: Check your shifter linkage under the car. It may have become disconnected. If it's full of fluid and your shifter linkage is OK then you need to tow it to a transmission shop. If all the fluid leaked out you will need to refill it. Remember that checking trans fluid is done with the engine running at idle and trans in park. Each time you add fluid to the system you should hold your foot on the brake with the engine running and cycle the shifter through all of the gears and then back to park. Check again. Add fluid if needed. Cycle through gears again, etc.....
I have W126 280se m110 722.3 transmission, the vacumm line is hanging loose at the engine bay, where does it connect??
I cover it in this video. ruclips.net/video/Wz4_eMrZk9o/видео.html Let me know you need additional info.
You can always buy a new cap or rod. The cap part number is #
The cap part number is "#" ? Clarify.
Hi Master, I am using W124 year 1992
My problem is when normal driving , gear 3 can't shift to gear 4 .
It become free gear .
What is the problems ?
Make sure your transmission fluid is new and is full. Usually a transmission which refuses to shift will require a complete rebuild.
Hello. What was youre problem? Your tranny starts from1, and goes to 3 (no 2. gear)?
Thanks a lot:)
Several annoying issues: Shifts from 1 to 2 and 3 to 4 were hard as nails. Shift from 2 to 3 was way too soon. Also the original modulator has a rubber cap on it that is prone to leaking vacuum. The new modulator is an improved design. Mercedes is not the only car manufacturer that uses vacuum modulators to control shifts. This is an extremely common maintenance item for older auto trans cars.
I have benz w124 1995 e320
What color type of this modulator valve well used in my car?
And am I can replacement it easily!?
Here is the modulator valve for your car. It should not be difficult. www.pelicanparts.com/More_Info/1262709179.htm?pn=126-270-91-79-M22&SVSVSI=3760&DID=13332
I've got a 1986 560SL with 200K miles that shifts smoothly while driving.
Its also a 722.3 transmission.
The problem is when I shift to or from Park/Neutral/Drive to Reverse I get a hard engage.
I can get a softer engage if I momentarily shift to Reverse, quickly back, then back to Reverse.
The Modulator looks original.
Have not checked the Modulator to see if it holds Vacuum - need to, but was concerned about
loosing my Transmission fluid.
Do you think I need to try a new Modulator?
You'll note very early in the video where I show the open port where the modulator resides that there is no transmission fluid which had dripped down over the lip of the pan. It's dry. Thus there is no fluid loss when removing it. If your transmission shifts properly and the only thing wrong is a hard reverse engage then I would say your modulator is not the issue. Without knowing what you consider to be a "hard engage" into reverse, it's tough to say where the problem may reside, however there is a fair amount of discussion on this topic. Here is one example: www.peachparts.com/shopforum/diesel-discussion/376603-only-using-half-springs-722-3-transmission-reverse-piston.html Your issue may be related to the reverse clutches or springs insde the transmission. I would start with the basics however. Does you fluid look good? If it's not red, change it and the filter. Check all vacuum lines.
@@ImpalamansGarage Transmission fluid is bright red and full to correct level.
I can get a much less "thunk" by teasing it quickly into reverse, back out, and back in. Wondering if its vacuum. Can the way the Modulator is adjusted have an impact on this "thunk"?
Thanks also for that posting in Peachparts.
Interesting that a firm shift to Reverse is less wear.
@@cwmoser I highly doubt it is vacuum. The modulator, whether or it's bad or good, should have no effect on the engagement of reverse gear. The modulator regulates fluid pressure to control firmness of upshifts. I would just hold my foot on the brake and shift it into reverse and wait until it's properly engaged before reversing. I fear moving the shifter around like that might do more harm than good.
KOOL TANKS
Hello, I have some problem with shifting from my European 1983 w126 380. It shifts true the gears very fast, when I drive 40/45 kmh it’s already in last gear.. when I press the gas pedal driving 50 kmh there is no shift back, this only happens when I press the kickdown. Than as you press it the car wil drop 1 or 2 gears and brings a smile on my face.. But as soon as I release the “kickdown button” with the gas pedal it wil shift back to last gear.
Now I don’t know if this is normal or there is something wrong here..
Next problem..
when I floor it from stand still, it wil shift first to second smooth, around 5000 rpm maybe 4800rpm. Not sure. than the 3rd to 4th I need to let the pedal come up (release the “kickdown button with the pedal) because it wil go past 5500 rpm and feels like it won’t shift 🤷🏼♂️
Is this supposed to be like this or is there something wrong here to..
You may need to adjust the bowden cable. On my car a clockwise adjustment makes the transmission shift sooner. Counter (anti) clockwise makes the transmission shift later. Do this 1/2 turn at a time and test drive after each adjustment. The bowden cable adjustment determines WHEN the transmission shifts. The QUALITY (how hard or soft) the shifts are is determined by the adjustment of the vacuum modulator on the transmission. A clockwise adjustment of the vacuum modulator will make the transmission shift harder. A counter (anti) clockwise adjustment will make the transmission shift more softly. Both the modulator and bowden cable work in concert with one another. It will take you a while to make the adjustments and get your transmission shifting properly. The Mercedes factory set these adjustments by measuring transmission fluid pressures during the manufacturing process. Lastly, when the transmission is shifting from 3rd to 4th under a heavy throttle condition, you may find it necessary to let up (decrease throttle pressure) to make it shift. In general, under wide open throttle you want the transmission to shift at the shift points noted on the speedometer. There are marks on the speedometer showing about where the car should shift when you floor it.
Here is an excellent document on how to adjust your Mercedes transmission. This document is for a diesel but it may be of help. jenniskens.livedsl.nl/Technical/Tips/Files/Mercedes%20722.4%20adjustment%20guide.pdf
@@ImpalamansGarage the best, thanks very much man. I really appreciate 💪🏽 I’ll let you know if this works 😁
Did it fix your problem?
Yes but it required dialing in. The adjustability of the new modulator is nice.
@@ImpalamansGarage Cool!
did this fix your hard shift into 4th?
Yes. The adjustability of this new version of the modulator is nice. Keep in mind the quality of shifts is dictated by the modulator and the timing of the shifts is regulated by the Bowden cable adjustment. They work together so you will need to tweak both of them.
@@ImpalamansGarage great! I'll dig deeper! Great video
Did you try to adjust this yet?
I plan to over the next day or two. Will reply to this video's comments with findings.
so what was the result of your labour?
The transmission shifts so much better than before. With the updated modulator and adjustments plus new vacuum lines in several areas.... the driving experience is very nice. In some instances, depending on the driving conditions I have noticed a very slight flare from 2 to 3 but this has only happened once or twice. Debating on whether or not to make another small adjustment. Guess I will just have to drive my classic Mercedes some more to determine!
@@ImpalamansGarage Once you put that plastic cap on, can you remove it? I have a new injection pump with bigger elements. The car shifts great except for the 2-1 down shift is rough. I used the fine adjustment and the shift improved slightly. If I could just get that cap off and adjust it more I believe the problem will be solved.
My R129 won’t shift to any gears you think replacing this might help?
Sounds like you've got some troubleshooting to do. Even if the modulator was not working at all, I think your transmission would still shift. I would start with the Bowden Cable. Have you tried adjusting it? Trying screwing the Bowden Cable clockwise (inward) for several turns and see if that has an effect. You are saying your transmission stays in 1st gear no matter what ?
Impalaman's Garage it actually not picking up any gears it I can move it from RD23 but nothing happens the engine just revs
@@joshuapena1314 Have you confirmed that your shift linkage under the car is connected properly? If it is connected properly it sounds like a transmission rebuild is needed.
Impalaman's Garage that’s the first thing o checked and both bushings were missing so I replaced both of the i even went ahead and bought a brand new shifter but still no luck I also flushed transmission fluid out and replaced the filter, Jesus sounds like it’s gonna be an expensive fix
Might be a better option to find a good used one that you know is good to go. Install it. Then buy a rebuild kit for the old one and learn to rebuild one at home.