Thank you for this!😊 Just fitted the 4-channel replacement model to a 16mm scale steam locomotive model from '85 with a knackered 27MHz system (though the two, original servos are fine), and couldn't figure out where the power needed to go - saw yours fed in through Ch1, so shoved my power connector in Ch3, hoped for the best, and it works!🥳 Just need to re-jig so the regulator isn't half-open by default next, where this r/c has throttle+brake rather than just throttle like the old system.🤔 Switched on, bound the transmitter, and it automatically centred the throttle servo. Can't have everything go to plan, eh?!😅 Thank you again.
Many thanks for this.. any ideas why once I get the red light to say bind is complete, that when I turn power back on its not bound? I have a r3fs and cr2s.v2.
Is it correct that my throttle stick is on the right, which moves left and right and my steering is on the left which operates left and right steering by pushing up and down? Feels like it's the wrong way round
Hello, thanks for your nice video. Does the transmitter use 1,2 or 1,5 volt AA batteries? Because i cannot find 1,5v rechargeables. Or does it work with rechargeable 1,2v batteries ?
Just built tamiya hornet but I get a lag when moving stick forward (accelerate) reverse is ok I am a noob and new to setting an RC car up I have th trim up position and st nor is this right? thanks
Hi I have an older FTX vantage and I think it needs to be recalibrated but I can’t seem to find the button that is on yours and I can’t seem to find anything on it thanks
Thank you for this!😊 Just fitted the 4-channel replacement model to a 16mm scale steam locomotive model from '85 with a knackered 27MHz system (though the two, original servos are fine), and couldn't figure out where the power needed to go - saw yours fed in through Ch1, so shoved my power connector in Ch3, hoped for the best, and it works!🥳 Just need to re-jig so the regulator isn't half-open by default next, where this r/c has throttle+brake rather than just throttle like the old system.🤔 Switched on, bound the transmitter, and it automatically centred the throttle servo. Can't have everything go to plan, eh?!😅 Thank you again.
Bin scratching my head for last hr trying to figure this out lol this my first rc build. Thanks for your help 👍
No problem you’re welcome 👍🏼
Thank you so much, went through 3 vids before yours and now have it set up 👍
No problem glad it helped.
Great video, just bought 2 absima receivers to go along with my existing receiver and handset. Now I can swap between cars in seconds.
Many thanks for this.. any ideas why once I get the red light to say bind is complete, that when I turn power back on its not bound? I have a r3fs and cr2s.v2.
No problem. Does this happen even when you’ve taken the bind plug out?
@@spudskirc4458 Yes it does annoyingly!
Really helpful man! Thx a lot.
No problem glad it helped :)
Thanks for upload is helpful 👍
No problem glad it helped 👍🏼
Brilliant, thankyou
Thanks for the video, it's very helpful. Can you bind more than one receiver to that Transmitter?
Thanks spudski lad
Why is my steering and throttle reversed, I have to switch the buttons on the transmitter to reverse on both. Any help appreciated.
Do you have to do the same procedure with the Abisma cr4s?
Is it correct that my throttle stick is on the right, which moves left and right and my steering is on the left which operates left and right steering by pushing up and down? Feels like it's the wrong way round
Yes that’s the wrong way, if you swap the plugs over in your receiver channel 1 and 2 then it should be the correct way.
@@spudskirc4458 thank you soo much.
@@JayJay-1985 No problem 👍🏼
Hallo, kann ich den gyro im Empfänger auch über den Sender einstellen oder nur am Empfänger selbst? Danke
Hello, thanks for your nice video.
Does the transmitter use 1,2 or 1,5 volt AA batteries?
Because i cannot find 1,5v rechargeables. Or does it work with rechargeable 1,2v batteries ?
Thank you 🙏
You're welcome :D
Thanks mate
Great tip , thank you.
Just built tamiya hornet but I get a lag when moving stick forward (accelerate) reverse is ok I am a noob and new to setting an RC car up I have th trim up position and st nor is this right? thanks
Hi I have an older FTX vantage and I think it needs to be recalibrated but I can’t seem to find the button that is on yours and I can’t seem to find anything on it thanks
Hi, Is it a Vantage brushed or brushless you have? If it’s brushless and no button then it’s the original esc and different calibration process
How many cars can you run on the Abisma SR2S?.
There isn’t a limit how many times you can bind it to other receivers however sometimes when changing car you may need to rebind.
Mine dont turn red when turn on does nothing
The transmitter or receiver?