As he didn’t mention it, for anyone who has a seized sensor and they don’t have an impact tool, I heated mine with a blowtorch 👍🏻 but of course, be very careful when doing this as there are a lot of wires and plastic components that are around the bank 1 sensor
Something like that : www.amazon.co.uk/Baceyong-Oxygen-Sensor-Installation-CUT-OUT/dp/B0978RR5QW/ref=mp_s_a_1_11?keywords=lambda+sensor+socket&qid=1661179807&sr=8-11
En mi 206 había una fuga de gas en la parte delantera entre los tubos de escape, hizo mucho y se arrastró, arrancó y se encendió la lámpara de control del motor.
@@orenweinstock6867so this statement is true then ? : " White and white are heater wires, it doesn't matter whether hot or ground goes into which white wire. "
@@orenweinstock6867 oh god damn it I also bought a third party lambda sensor and I never understood why the hell I get the code every now and then, it drives me nuts. Should have bought the original part but it cost a lot more ffs :/
@@VukLazarevic check another thing that raised emission trouble coded as well >> I had a leak of exhaust gasses in the middle flange below the vehicle (they found it in the MOT). Once solved and new original lambda installed car run perfectly and fuel consumption improved
عاشت ايدك توب
Siempre se cambian los 2 sensores?? tengo combustión mala, con cambiar el sensor primario no qedariaa solucionada la falla?
As he didn’t mention it, for anyone who has a seized sensor and they don’t have an impact tool, I heated mine with a blowtorch 👍🏻 but of course, be very careful when doing this as there are a lot of wires and plastic components that are around the bank 1 sensor
Another thing always clean off surfaces before replacing the part for a better flush fit
Every thing is perfect
Mi carro es un Peugeot 207 a veces arranca y a veces no será por el sensor de oxigeno múltiple de escapé
Hi, which socket do I need to get out the Lambda Sensor?
Ok I just saw it on the video, it is 22mm.
Hard to see it watching the video via Smartphone 😆.
Something like that : www.amazon.co.uk/Baceyong-Oxygen-Sensor-Installation-CUT-OUT/dp/B0978RR5QW/ref=mp_s_a_1_11?keywords=lambda+sensor+socket&qid=1661179807&sr=8-11
Espero algún comentario para buscar soluciones saludos desde Guatemala
En mi 206 había una fuga de gas en la parte delantera entre los tubos de escape, hizo mucho y se arrastró, arrancó y se encendió la lámpara de control del motor.
My car stop I make u trun than stop I try take starter but no start
is it the same sensor, below and above ?
No
I own the same car. I discovered there is no sensor underneath, will it cause a problem?
Do you have a check engine light on dashboard ? Can you read obd trouble code and see if there is an error code ?
Is the sensor needed to be programmed after installation
Not at all
Never replace these sensors with aftmerket ones!
The Ecu is programmed to work only with the Oem Ngk sensor.
Both sensors are the same?
Hi 👋 not the same sensors
color codes ? if using universaL lambda...how to tell 2 heater wires apart....that would be usefull
mechanics.stackexchange.com/questions/88680/lambda-wiring-diagram-wrong-from-bosch
@@orenweinstock6867so this statement is true then ? : " White and white are heater wires, it doesn't matter whether hot or ground goes into which white wire. "
Correct
I also used generic Bosch sensors on another car. Works fine
Is this the anti pollution fault repair
Yes
Have they malfunctioned since you replaced them?
Eventually I was needed to replace with Peugeot genuine ones, those didn’t work well
@@orenweinstock6867 what was the problem? Did it report the antipollution faulty code again?
@@VukLazarevic - Exactly, emission code came up again ! non-original parts didn't work for me in this case
@@orenweinstock6867 oh god damn it I also bought a third party lambda sensor and I never understood why the hell I get the code every now and then, it drives me nuts. Should have bought the original part but it cost a lot more ffs :/
@@VukLazarevic check another thing that raised emission trouble coded as well >> I had a leak of exhaust gasses in the middle flange below the vehicle (they found it in the MOT). Once solved and new original lambda installed car run perfectly and fuel consumption improved
Hallo, Guten Tag
bis wie viel N M können wir fest machen?
ihre Video gefällt mir sehr.
Dankeschön für gut information.
Gruß von Deutschland.
Hello ! Happy you like the video. Can you please re phrase question I’ll be happy to help
bro...the music. wtf...😮