Never owned or shot an FX rifle, so can only comment on what your video showed and like you said, the block looks to be very nicely machined. Didn't notice any manufacturing marks on any of the components you removed, so you have to give it to FX for quality control on this aspect. Thanks for showing the methodical breakdown and description.
Brilliant stuff guys, I love the disassembly series 😎😎 I shot your panthera Saturday and managed a single pellet hole at 50 yards with 6 shots. Best panthera in the UK.
nice tear down mate . to be fair not as complicated as i thought it were going to be . as long as your carful not beyond a pretty component diy-er . think your bang on about the barrels . not saying every fx is the same but most i have seen when you stiffen up the liner they seem to shoot better . plus that oring malarkey seems like a faf to me
thanks mate, yes well within a diy repair👍 Fx guns all look more complicated than they are to me they have lots of bits but they go together easily 👍 thanks for watching
Wow the plenum on the sub 12 in damn near non existent that’s so sad and you don’t even get the quick tune system 😢 why don’t you get the FAC version or. Is it to much a hassle?
I'm impressed by the block too, though obviously on cnc the design is complex; overly in my view. I'd bet a Chinese person has already produced a CNC test version of much simpler design, fewer screws and parts to go wrong, also cheaper to build. The barrel support appears to be an example of a part that only exists because of a design fault with the block. Thanks again.
Hey! I dry fired my rifle to make sure no air was in the system and I believe this bent my valve. I now have a massive leak through the barrel and it wont hold air. Do you have the v2 valve installed (which is thicker) or any other modification that allows you to dry fire it?
Hi mate love the channel tell my local gun shop if you dont like it neither do i haha. For precise accuracy at 50m what pcp would you recommend for bench rest ?
Hi great video as always. I'd like to pick your brains if that's ok I've been shooting for a long time and I'm a springer shooter but I've got my first PCP today a daystate wolverine r ( used ) it's a great gun and very accurate the only issue with it it's only doing 10.5 ft lb with bsa goldstar 8.64gn I would have thought it would have been slightly higher is there anything I can do ( never worked on a pcp ) to increase the fps to increase the ft lb. Many thanks in advance phill
if you try 10.34 pellets it will be much closer to 12lbft if it's still a bit low have a look on the Daystste youtube channel there is a vid on the wolverine which will help 👍👍
Hi geoff / Jake I've tried heavier h&n baracuda match @ 10.65gn the power is now 10.9 ft lb so not much difference from the 8.64gn the reg is set at 120 bar could the hammer spring need a tweek and is it something I could do myself Many thanks in advance Phill
@@sub12airgunners hi guy's that's great thx for your reply. Just one more question if I may to remove the safety catch to get to the anti tamp bar to be able to make adjustments do I have to degas the gun first or is it something that can be done while gassed. Many thanks in advance phill
the ping is often the valve return spring resonating, a simple delrin slip ring on the ends of the spring can make a big difference to this the cylinder guns sometimes need a baffle in the cylinder 👍👍
Do you still have eBay store?,im trying to get a part you made for the fx dreamline.I’m getting aluminum shavings under my trigger from the two parts hitting each other.
@@sub12airgunners I really want one!,im communicating with fx now about the problem,they could fix this with a part like youve made.please consider making some as I’m sure other dreamline owners are having the same problem.thank you.
@@1776freddie i contacted FX when i found this problem they asked for pics i sent them never got any response so i don't think they are that interested, i had one of the first DT in the uk so they have had a long time to sort it, i even sent pics of the ones we used to sell 😔😔
the ping is often the valve return spring resonating, a simple delrin slip ring on the ends of the spring can make a big difference to this the cylinder guns sometimes need a baffle in the cylinder
Love watching your videos but unfortunately they're all out of my price range. Any chance of modding an smk cp2. I'm sure you could ring every ounce of power and accuracy from it
Don’t think the guys would do it on the grounds of power. Every project they have ever done has been all about accuracy. They only ever look at power if it’s effecting accuracy ( which will always be about delivering consistent power levels). Being co2 and unregulated doesn’t really sit with their interests. ( but I could be wrong !)
Never owned or shot an FX rifle, so can only comment on what your video showed and like you said, the block looks to be very nicely machined. Didn't notice any manufacturing marks on any of the components you removed, so you have to give it to FX for quality control on this aspect. Thanks for showing the methodical breakdown and description.
thanks for watching 👍👍
Great video Jake ,the new barrel absolutely transformed that rifle and it is now everything it should have been out of the box.
Thanks Martin 👍👍
Another great video. Looking forward to the rebuild.
Thanks for watching 👍👍
Brilliant stuff guys, I love the disassembly series 😎😎 I shot your panthera Saturday and managed a single pellet hole at 50 yards with 6 shots. Best panthera in the UK.
thanks mate, it is pretty good now 👍😁
Another invaluable video for owners well done guys and brilliant of you to share👏
Thanks mate 😁😁
Excellent strip down guide .... Nice and easy to follow and announcing the hex key sizes is great
Thanks Lee 😁😁
As always you explained so well 👍
Thanks for watching 👍👍
Cracking video as always Jeff, breat watch, thanks so much for sharing Cheers 👌👌👌👍👍👍👍👍👍
thanks for watching 👍👍
A nice tutorial and its come on in leaps an bounds. keep up the good work.
thanks Tim 👍👍
Great strip down guide. Clear and easy watching.
thanks for watching 👍
Well done Jeff. Do you write down what you are going to say or just commentate as you go along? Your commentary is seamless.👍👍
A bit of both really we don't write it all down but we do make notes 😁😁
Awesome video...I like your Hollywood voice too. Thanks a lot
Thank you so much 😀
Amazing strip down with so many parts to deal with. I’d be ok taking everything apart - putting it back together might not go so well! 😂
😂😂😂😂 it looks worse than it is 😁😁
Awesome video 👍
Thanks for watching 👍👍
nice tear down mate . to be fair not as complicated as i thought it were going to be . as long as your carful not beyond a pretty component diy-er . think your bang on about the barrels . not saying every fx is the same but most i have seen when you stiffen up the liner they seem to shoot better . plus that oring malarkey seems like a faf to me
thanks mate, yes well within a diy repair👍 Fx guns all look more complicated than they are to me they have lots of bits but they go together easily 👍 thanks for watching
Awesome 👍
Thanks for watching 👍👍
very informative, Great video guys 👍🏼
Glad you enjoyed it!
Well done Jeff. Do you write down what you are going to say or just commentate as you go along? Your commentary is seamless.
😁😁
Wow the plenum on the sub 12 in damn near non existent that’s so sad and you don’t even get the quick tune system 😢 why don’t you get the FAC version or. Is it to much a hassle?
I think the clue is in their channel name 😊
it's a lot of trouble in the UK to get a Fac so we do the vids on the sub 12 as that's what most people have 👍👍
Thanks for the great video. Tell me, is it possible to remove the pressure regulator without dismantling the trigger?
yes you have to remove the guard but the reg will come out 😀
Mine dumps all air out the barrel I’ve replaced valve seat and houseing and oil and all o rings and it still pours out of barrel any ideas?
it's the valve in some way, have you tried backing the hammer spring off and seeing if it still leaks 👍👍
😊
Thanks for watching 👍👍
I'm impressed by the block too, though obviously on cnc the design is complex; overly in my view. I'd bet a Chinese person has already produced a CNC test version of much simpler design, fewer screws and parts to go wrong, also cheaper to build. The barrel support appears to be an example of a part that only exists because of a design fault with the block. Thanks again.
yes i think any support they can give the stx barrel is a good thing 👍
Great, precise explanation, but I own an EDGUN MATADOR LONG rifle. Please make a video of how to disassemble it, if you please. Thank you very much.
it is on the list of guns to do 👍
@@sub12airgunners
Hello, very good video, thank you.
One question: where can I get the tool to remove the valve seat?
hi we supply Bagnal & Kirkwood they may have them in stock 👍
@@sub12airgunners thanks for answering. I am interested in the tool. but I can't find it on the web. Can you post the purchase link please?
Hey! I dry fired my rifle to make sure no air was in the system and I believe this bent my valve. I now have a massive leak through the barrel and it wont hold air.
Do you have the v2 valve installed (which is thicker) or any other modification that allows you to dry fire it?
we have the original valve in our one but we are only sub 12 fb so i don't think it's a problem
Hi mate love the channel tell my local gun shop if you dont like it neither do i haha.
For precise accuracy at 50m what pcp would you recommend for bench rest ?
i would go S/H HFT500 for that sort of money 👍
@sub12airgunners cheers mate
Great video as always! Do you plane on selling the tool to remove valve seat. I have the one for wildcat but I would like the one for the panthera
Yes we will be doing some 😁 thanks for watching
Hi there, do you or do you know any company who sell a LW barrel conversion for the panthera? Thank you
hi sorry no i don't know of anyone that does it a service but any good gun smith will be able to 😀
Complicated or what?
it looks worse than it is to be honest 👍 thanks for watching
any chance doing a budget one.reximex regime ?
next year we are going to do some budget guns 😁
Hi great video as always. I'd like to pick your brains if that's ok I've been shooting for a long time and I'm a springer shooter but I've got my first PCP today a daystate wolverine r ( used ) it's a great gun and very accurate the only issue with it it's only doing 10.5 ft lb with bsa goldstar 8.64gn I would have thought it would have been slightly higher is there anything I can do ( never worked on a pcp ) to increase the fps to increase the ft lb. Many thanks in advance phill
if you try 10.34 pellets it will be much closer to 12lbft if it's still a bit low have a look on the Daystste youtube channel there is a vid on the wolverine which will help 👍👍
@@sub12airgunners
Thx for your reply I'll give them a go and see how things go
Many thanks for getting back in touch regards phill
Hi geoff / Jake I've tried heavier h&n baracuda match @ 10.65gn the power is now 10.9 ft lb so not much difference from the 8.64gn the reg is set at 120 bar could the hammer spring need a tweek and is it something I could do myself
Many thanks in advance
Phill
@@phillipward4862 yes it is very simple, 1.5mm hex key
@@sub12airgunners hi guy's that's great thx for your reply. Just one more question if I may to remove the safety catch to get to the anti tamp bar to be able to make adjustments do I have to degas the gun first or is it something that can be done while gassed. Many thanks in advance phill
I have a leak on my brand new Fx Panthera, the air is coming out of the barrel, did the disassembly and couldn’t figure out what’s the problem !!
if it's coming from the barrel it's 99% the firing valve or seat
@@sub12airgunners found out it was the valve seat took it out and changed a seal, now it work works perfect !! Thank you so much 🙏
under a grand i should of mentioned
hi can you help ,I have sub 12 Panthera and its pinging when firing ,have you come across this before
the ping is often the valve return spring resonating, a simple delrin slip ring on the ends of the spring can make a big difference to this the cylinder guns sometimes need a baffle in the cylinder 👍👍
What's the weight of this part alone ?
5:38
Please help
sorry we didn't get the weight of the block on it's own
Do you sell that valve seat removal tool?
bagnal & kirkwood sell them 😀
Do you still have eBay store?,im trying to get a part you made for the fx dreamline.I’m getting aluminum shavings under my trigger from the two parts hitting each other.
we do still sell bits on ebay but we don't have any of the shuttles i don't know when we will have more sorry
@@sub12airgunners I really want one!,im communicating with fx now about the problem,they could fix this with a part like youve made.please consider making some as I’m sure other dreamline owners are having the same problem.thank you.
@@1776freddie i contacted FX when i found this problem they asked for pics i sent them never got any response so i don't think they are that interested, i had one of the first DT in the uk so they have had a long time to sort it, i even sent pics of the ones we used to sell 😔😔
how can you stop the pinging noise
the ping is often the valve return spring resonating, a simple delrin slip ring on the ends of the spring can make a big difference to this the cylinder guns sometimes need a baffle in the cylinder
Do you sell the modified tool to remove the valve?
we don't have any at the moment but we will be doing some soon 👍👍
Is there an online store where I can track to see when they come in stock?
@@11trevord we supply B & K spares.bagnallandkirkwood.co.uk/product-categories/
Lcs sk19 vs
Sidewinder
Love watching your videos but unfortunately they're all out of my price range. Any chance of modding an smk cp2. I'm sure you could ring every ounce of power and accuracy from it
Don’t think the guys would do it on the grounds of power. Every project they have ever done has been all about accuracy. They only ever look at power if it’s effecting accuracy ( which will always be about delivering consistent power levels). Being co2 and unregulated doesn’t really sit with their interests. ( but I could be wrong !)
Thanks for watching 👍👍