exelente video sobre esta placa, ya que no se encuentra mucha informacion de ella en linea, a la espera de mas videos sobre ella. Saludos desde Argentina
You are welcome. The best thank you for me is to subscribe to my channel. Your subscription is stamp of approval and my videos will be suggested to more people and this will help me. I appreciate it. thanks❤️
Have you test maximum range? How much rage it can achieved? Please try to upload video on real time environment test ur sharing valuable information on every video thank you
No one can give you a number for range. a test in one place will be different on other place. environment will greatly affect the range. I am planning to test the range but it will not be valid everywhere.
Good Morning, I’m using some HTCC-AB01 like sender, I’m sending some value read from 5 sensors connected to their GPIO. I’m using also an HTCC-AB01 like receiver. I need to know how many HTCC-AB01 used like sender can be handle by one HTCC-AB01 used like receiver. Can you help me?
Simultaneously one will work but if there is a theming gape between sensing data from multiple devices , it should work with as many transmitter as you want.
for the range no one should give a figure. it could be 500m or 90km. if two of this module are on top of two mountains, you can communicate with over 90km. but as the obstacles come, it will be reduces to few 100 meters.
Hi, can you please explain if can control the relay modules you suggested, with the HelTec Cube Cell AB02, with the code you have for controlling the LEDs wirelessly? How many GPIO available do I need for each relay? can I use the same GPIO pin number for the switch on the CubeCell transmitter & the relay on CubeCell receiver? or do i need two GPIO pins for each relay between transmitter and receiver? about six of the relays (for lighting) are in six different places, the other about 7 are in one place. Thanks, happy to give donation for working code for this. Also hoping to have repeater cube cell units to increase range/go around obstacles.
As other people tried to ask you, but no reply, so i try again: In the end of this video you said that LED-toggle buttons are a separate video and the link is in the description. Where?
I have video waiting to be published. right now you can't it without the gateway. you need to put some kind of identification of code between TX and RX so you know which receiver or RX receive it. Please subscribe. I appreciate it and helps my channel grow. Thank you
Hi, you are welcome. it is unlike anything you have seen. I will test it. but the test result depends on the area and building and obstacles. but it would be 10 to 100 times of WiFi and Bluetooths.
Hi, great video my friend! I have a question for you. How can I read battery level from Cubecell. Do you have any code for that purpose? Greetings from Paraguay
7v to 4.2v interesting🤔 Robojax I can cluster these as a scaleable(2 cell - 21 cell) Wireless(Mesh) Bms(Battery Management System). Tap in via the balance cable and log "Individual" cell voltages "Collectively" while using the GPIO pins to toggle OCP OVP LVP relays or mosfets rather. All-in-one package. I would base is off the DC/DC ISDT Air 6s bluetooth charger although instead of 2.4Ghz BLE it would have AI + LoRa range and speed and much more. Imagine a Mesh BMS with built-in charging and full protection wake over LAN remote access via dual band & LTE fail over. 1mv active balancing smart storage discharging based on an inactivity or schedule options and features are only limited to your imagination and programming skills. Thanks Robojax
By the way, I often see Lora module connected to raspberry pi in papers, obviously Linux system. How to find this kind of module? I am very confused that most modules are connected to the notebook with WINDOWS operation system.
students and most people use them on windows. I would have make video if I knew if there were enough interest. But no one watches this. the resources link is in the description of this video. you can see where to get it from.
Hi sir.... Your explanation about cubecell was awesome..i got more information about cubecell from this video... I need one help... I interface temperature sensor dth22 with cubecell HTCC ab01 ...i got output...but I need code to transfer the temperature information from one cubecell HTCC ab01 to another cubecell htcc ab01...please help. Thanks in advance...
nrf24L01 has 1mW power and CubeCell can go to 22dBm which 158mW so this is way way powerful. nrf24L01 is operating at 2.4GHz (2400MHz) and as the operating frequency is reduced, the range increased. CubeCell has 433 to 915MHz.
Hi, Do you have code available for the HelTec CubeCell AB02A that can wirelessly control relays by the GPIO pins? (As you said in your comments section that you have the code for LED controlled wirelessly by Cube Cell for USD$50) Please can I also ask if when controlling Relays, is it possible to use the same GPIO pin number for switch in (on Transmitter) & also Relay out (on different, receiver unit) (I am controlling about 13 + relays) Please also, for code making in AU915 - 928 (not US915)
Hi, you can't control a relay directly but you can control a relay module which has relay driver like a transistor. I have tones of videos on using relay up to 16 channel.
@@robojax Hi, can you please explain if can control the relay modules you suggested, with the HelTec Cube Cell AB02, with the code you have for controlling the LEDs wirelessly? How many GPIO available do I need for each relay? can I use the same GPIO pin number for the switch on the CubeCell transmitter & the relay on CubeCell receiver? or do i need two GPIO pins for each relay between transmitter and receiver? about six of the relays (for lighting) are in six different places, the other about 7 are in one place. Thanks, happy to give donation for working code for this. Also hoping to have repeater cube cell units to increase range/go around obstacles.
Hi, that code needed lots of work. I am not sure when I am going to make video on that. All my codes and videos are free. but if you make donation bit.ly/donate-robojax of USD$50, I will send it to your email. but this is not selling the project or support or anything as the project worth way more.
Arduino UN/Mga are Microcontroller. This module is itself a microcontroller and you can program input and output of it like Arduino UNO. just see which option is available. I've explained it.
Hola, parece que no has visto el video. He demostrado cómo encender / apagar el LED con dos de ellos. cuando no mires completamente, seguro que te confundirás.
Walaikum salaam, I have not tested it but it would be in km if not 500m. it depends on the surrounding. The output power is very high with comparing it to nrf24L01. like 158 times more.
I greatly appreciate this video. It covers all the essential information that I felt the Heltec Docs fail to properly convey.
Glad you enjoyed it!
Cleared up many questions. Thanks!
exelente video sobre esta placa, ya que no se encuentra mucha informacion de ella en linea, a la espera de mas videos sobre ella. Saludos desde Argentina
Me alegro que lo haya encontrado útil. vienen más videos sobre este tema.
Nice video ! Clear and precise. Thanks a lot.
Glad it was helpful!
Great Video
This video was very helpful, thank you!
You're so welcome!
Very nice video
Thanks
Excelente video!, sería muy interesante ver la segunda parte.
Saludos
Gracias. Me alegro de que te haya gustado. Una vez que tenga tiempo, vendrán más videos de esta serie.
Muchas gracias, Robojax.
Me ha ayudado a empezar con el proyecto.
Salud !
Excellent 🙌
VERY NICE!
Very!
Good
So nice
Great video! Can you do the HTCC-AB02S next, please? Thanks for the great explanations!
Yo uare welcome. I will see if I get. I don't have it on hand.
excelent video !!! a example with lorawan pleasee
very interesting project. I will keep it in mind.
Thanks for the review, is it possible to program it without using the arduino framework?
Yes you can if you read the documentation and wire your own code in language you like
But is there any framework or HAL available and open source, like for ARM? PSOC is more kind of a picky microcontroller...
thank you
You are welcome. The best thank you for me is to subscribe to my channel. Your subscription is stamp of approval and my videos will be suggested to more people and this will help me. I appreciate it. thanks❤️
Have you test maximum range? How much rage it can achieved? Please try to upload video on real time environment test
ur sharing valuable information on every video thank you
No one can give you a number for range. a test in one place will be different on other place. environment will greatly affect the range. I am planning to test the range but it will not be valid everywhere.
Good Morning,
I’m using some HTCC-AB01 like sender, I’m sending some value read from 5 sensors connected to their GPIO. I’m using also an HTCC-AB01 like receiver.
I need to know how many HTCC-AB01 used like sender can be handle by one HTCC-AB01 used like receiver.
Can you help me?
Simultaneously one will work but if there is a theming gape between sensing data from multiple devices , it should work with as many transmitter as you want.
thanks for sharing... what's the range and power consumption in real environment with some obstacles like trees and buildings
for the range no one should give a figure. it could be 500m or 90km. if two of this module are on top of two mountains, you can communicate with over 90km. but as the obstacles come, it will be reduces to few 100 meters.
Hi, can you please explain if can control the relay modules you suggested, with the HelTec Cube Cell AB02, with the code you have for controlling the LEDs wirelessly? How many GPIO available do I need for each relay? can I use the same GPIO pin number for the switch on the CubeCell transmitter & the relay on CubeCell receiver? or do i need two GPIO pins for each relay between transmitter and receiver? about six of the relays (for lighting) are in six different places, the other about 7 are in one place. Thanks, happy to give donation for working code for this. Also hoping to have repeater cube cell units to increase range/go around obstacles.
Não achei a continuação onde você explica como acionar o Led usando o cubecell via lora...
As other people tried to ask you, but no reply, so i try again:
In the end of this video you said that LED-toggle buttons are a separate video and the link is in the description.
Where?
Hi, because I did not see enough internet in this module , I did not make the video. Perhaps I should make it.
Has anyone managed to connect an ili9341 lcd display to one of these? Heltec say it is fully Arduino compatible which is rubbish.
Thanks for the very informative video.
May I also ask, how could I select which receiver to send the message to?
Thanks.
I have video waiting to be published. right now you can't it without the gateway. you need to put some kind of identification of code between TX and RX so you know which receiver or RX receive it. Please subscribe. I appreciate it and helps my channel grow. Thank you
Is it possible to use this dev board with meshtastic firmware?
Could it be Two Way Communication On LoRa? like Command Sent And receive it and Sent back
that is exactly it is made for. I believe I have demonstrated it. Please watch
Hi Great video can you tell me where I find the remote switch you demonstrated?
sorry what remote switch?
@@robojax its the switch you demonstrate at the end of the video, where you turn the LEDon and off, But i cant find any info for it?
Hi, Is the code posted for turning on and off the LED somewhere? I would also like to add sleep mode until the button is pushed. Thanks
Hi, Interesting feature to be used. I will consider that in the next video I am going to make on this board.
@@robojax Okay thanks, In the meantime before you make the video showing the remote control of the LED is there a way you could post your code?
Hi,thanks for this video.Did you have the opportunity to test the range of this 2 devices?
Hi, you are welcome. it is unlike anything you have seen. I will test it. but the test result depends on the area and building and obstacles. but it would be 10 to 100 times of WiFi and Bluetooths.
Hi, great video my friend! I have a question for you. How can I read battery level from Cubecell. Do you have any code for that purpose? Greetings from Paraguay
Hi, I hade the code but I lost them. Now it would be hard to make the project again and write the code. sorry.
Here is the video and see if you can get something from the video ruclips.net/video/rSPN-8ZK0AM/видео.html
which code? the module has resource page from Heltic.
Can we used like telemetry for drone
this is just a module to send and receive data. yes you can use one as RX (receiver) and another one as TX (transmitter) to send and receive data.
7v to 4.2v interesting🤔 Robojax I can cluster these as a scaleable(2 cell - 21 cell) Wireless(Mesh) Bms(Battery Management System). Tap in via the balance cable and log "Individual" cell voltages "Collectively" while using the GPIO pins to toggle OCP OVP LVP relays or mosfets rather. All-in-one package. I would base is off the DC/DC ISDT Air 6s bluetooth charger although instead of 2.4Ghz BLE it would have AI + LoRa range and speed and much more. Imagine a Mesh BMS with built-in charging and full protection wake over LAN remote access via dual band & LTE fail over. 1mv active balancing smart storage discharging based on an inactivity or schedule options and features are only limited to your imagination and programming skills. Thanks Robojax
I would name it RJW-MBMS - ROBOJAX WOOTEN MESH BATTERY MANAGEMENT SYSTEM.
Sounds very interesting. Thanks. Please update us when done. Good luck.
By the way, I often see Lora module connected to raspberry pi in papers, obviously Linux system. How to find this kind of module? I am very confused that most modules are connected to the notebook with WINDOWS operation system.
students and most people use them on windows. I would have make video if I knew if there were enough interest. But no one watches this. the resources link is in the description of this video. you can see where to get it from.
i haveMT-M02 gateway, I already setup my cube cell, I need to know how I can give a command to the cube cell from HT-M02 gateway....?
The video on the gateway is coming soon.
Hi sir.... Your explanation about cubecell was awesome..i got more information about cubecell from this video... I need one help... I interface temperature sensor dth22 with cubecell HTCC ab01 ...i got output...but I need code to transfer the temperature information from one cubecell HTCC ab01 to another cubecell htcc ab01...please help. Thanks in advance...
great video how cann we send Data to a server with a Cubecell board ?
it needs cloud service. I will make video on how to use Could service.
@@robojax I'm looking forward to it! For example, connect it to TTN or chirpstack.
what is the range, without effective range, its as good as a nrf24L01
nrf24L01 has 1mW power and CubeCell can go to 22dBm which 158mW so this is way way powerful. nrf24L01 is operating at 2.4GHz (2400MHz) and as the operating frequency is reduced, the range increased. CubeCell has 433 to 915MHz.
Hi, Do you have code available for the HelTec CubeCell AB02A that can wirelessly control relays by the GPIO pins? (As you said in your comments section that you have the code for LED controlled wirelessly by Cube Cell for USD$50) Please can I also ask if when controlling Relays, is it possible to use the same GPIO pin number for switch in (on Transmitter) & also Relay out (on different, receiver unit) (I am controlling about 13 + relays) Please also, for code making in AU915 - 928 (not US915)
Sorry, meant to say HelTec AB02, Thanks really like your youtube explanations
Hi, you can't control a relay directly but you can control a relay module which has relay driver like a transistor. I have tones of videos on using relay up to 16 channel.
@@robojax Hi, can you please explain if can control the relay modules you suggested, with the HelTec Cube Cell AB02, with the code you have for controlling the LEDs wirelessly? How many GPIO available do I need for each relay? can I use the same GPIO pin number for the switch on the CubeCell transmitter & the relay on CubeCell receiver? or do i need two GPIO pins for each relay between transmitter and receiver? about six of the relays (for lighting) are in six different places, the other about 7 are in one place. Thanks, happy to give donation for working code for this. Also hoping to have repeater cube cell units to increase range/go around obstacles.
Hi, can you share the code for LED control please?
Hi, that code needed lots of work. I am not sure when I am going to make video on that. All my codes and videos are free. but if you make donation bit.ly/donate-robojax of USD$50, I will send it to your email. but this is not selling the project or support or anything as the project worth way more.
can I use it on an arduino board? like Uno or Mega?
Arduino UN/Mga are Microcontroller. This module is itself a microcontroller and you can program input and output of it like Arduino UNO. just see which option is available. I've explained it.
hola, como seria el codigo para mandar a encender un led desde una cubecell a otra ?
tengo 2 tarjetas cubecell estoy confundido con el envio de datos
Hola, parece que no has visto el video. He demostrado cómo encender / apagar el LED con dos de ellos. cuando no mires completamente, seguro que te confundirás.
Assalam alaikum Sir,
What would be the range ??
Walaikum salaam, I have not tested it but it would be in km if not 500m. it depends on the surrounding. The output power is very high with comparing it to nrf24L01. like 158 times more.