I bought the same Moser cover and in a few months the hardware was rusty. I know you won’t have this car by then (I saw your listing) but for the future owner, swap that hardware out if it is not stainless. Great video, as always.
Great Vid, gotta Moser Rear End with 4.10s in the Comp T/A and I love it with the T56! Great Vid. I did end up ditching the full spool for a Detroit Trutrack, though.
I installed a Detroit tru Trac carrier on my 94 project trans am I'm building.. it's a nice piece.. I installed Richmond 3:73s with Moser 28 spine cclip axles and timken bearings and seals internally...
@keilylmm6377 I went with the 33spline axles and c-clip eliminator kit. I did the rear end in 07 and ditched the full spool in 2015. I liked the trutrack so much. I installed one in my 2000 silverado Project truck.
@@TWAMotorsports that magna flow looks clean underneath.. that's why I was asking... 👍.. sounds nice too.. I've seen them cat back system go for 700.. pretty cheap compared to Borla which I like....👍
@@TWAMotorsports have a nice weekend.. I'll be tinkering around with my 94 TA this weekend doing the gauge pillars gauge pods while still waiting for my intake manifold to be completed by my engine builder at golen race engines.. I'm doing 2 gauge pods oil psi and water temperature on the ttop pillar inside.. 👍
Ok a few months ago I commented I'd like if you posted more vids on the red Trans Am and you said videos on the trucks get more views. However here we are now and your posting videos on this Camaro and also the Trans Am parts car,but rarely anything on the red trans am,what gives? it shouldn't take this long for parts.
Travis it’s your garage… do what makes you happy and don’t do things just to get views.. I understand taking breaks from certain projects.. take care bud
Great job, Travis. Love your attention to detail.
Thank you
I bought the same Moser cover and in a few months the hardware was rusty. I know you won’t have this car by then (I saw your listing) but for the future owner, swap that hardware out if it is not stainless. Great video, as always.
I wondered that when I was installing it.
I just did this exact job not bad. Transmission jack works great for a rear end job
That would be nice to have
GM recommends 80\90 gear oil for those rear ends
Good videos btw!
Thank you
Great Vid, gotta Moser Rear End with 4.10s in the Comp T/A and I love it with the T56! Great Vid. I did end up ditching the full spool for a Detroit Trutrack, though.
I installed a Detroit tru Trac carrier on my 94 project trans am I'm building.. it's a nice piece.. I installed Richmond 3:73s with Moser 28 spine cclip axles and timken bearings and seals internally...
@keilylmm6377 I went with the 33spline axles and c-clip eliminator kit. I did the rear end in 07 and ditched the full spool in 2015. I liked the trutrack so much. I installed one in my 2000 silverado Project truck.
@@mcbridemotorsports5788 very nice 👍
Yeah this should be fun
Good stuff
Great content as always. However I’d like to see some shots of that Camaro going down the road, even as a ws6 owner 😂
Thank you. Maybe I can do that
awesome, thank u sir
Thank you
Travis I’m curious what coil packs did you put on the ws6 ? My engine is basically the same build do you recommend a certain one? Thanks
Stock. All I will ever use
Looking nice..👍 por 15 does the trick....is that a magna flow cat back exhaust on that SS?
Thank you. Yes it is the budget magnaflow
@@TWAMotorsports that magna flow looks clean underneath.. that's why I was asking... 👍.. sounds nice too.. I've seen them cat back system go for 700.. pretty cheap compared to Borla which I like....👍
@keilylmm6377 yes they are way cheaper. Things are crazy priced nowadays
@@TWAMotorsports have a nice weekend.. I'll be tinkering around with my 94 TA this weekend doing the gauge pillars gauge pods while still waiting for my intake manifold to be completed by my engine builder at golen race engines.. I'm doing 2 gauge pods oil psi and water temperature on the ttop pillar inside.. 👍
@keilylmm6377 thank you. You too
Are you also getting brakes for the front? And will those fit stock 02 z28?
Yes. Came in kit listed in video description. Yes they fit 02 z28
Nice calipers are those the stock ones?
Yes. Stock painted with paint listed in video description
Someone come buy this!!
Now
That rotten egg type of smell. 😂. Different ones definitely have a very strange odor that you never forget
It will smell up a whole shop. Lol
Why do you still have the sticker on your cap?🤔
What if I want to return it?
Ok a few months ago I commented I'd like if you posted more vids on the red Trans Am and you said videos on the trucks get more views. However here we are now and your posting videos on this Camaro and also the Trans Am parts car,but rarely anything on the red trans am,what gives? it shouldn't take this long for parts.
I'm sure he makes videos based on what you want to see. Just you.😅
I do what I can when I can.
@deanm72 can't please everyone
Travis it’s your garage… do what makes you happy and don’t do things just to get views.. I understand taking breaks from certain projects.. take care bud
Thank you. Kinda what I do