My DIY Catamaran Engine Set-Up Is Complete!
HTML-код
- Опубликовано: 20 июн 2024
- plenty of 'summer solutions' in this episode. but I do get my engines ready for use!
Best quality cable seals here: www.svb24.com/en/brands/scans...
My Instagram: @boat.fella
Facebook: / wildlingssai. .
Business Enquiries: thewildlingsofficial@gmail.com
Thank you SO much to the incredibly generous people who use the links below
PayPal: www.paypal.me/wildlingssailing
Ko-fi: www.ko-fi.com/wildlingssailing
Patreon: / wildlingsailing
Amazon Wishlist: www.amazon.nl/hz/wishlist/ls/...
The music I'm actually listening to: open.spotify.com/playlist/22s... 
Хобби
![We Hid the Windlass Locker under the Deck. [EP130]](http://i.ytimg.com/vi/yW0Q-ZGdyxw/mqdefault.jpg)
![Megan Thee Stallion - Otaku Hot Girl [Official Audio]](http://i.ytimg.com/vi/USxIYOaIpig/mqdefault.jpg)
Soldering wires together should never be done. It's for electronics, not for heavy current. Guess what happens when the wire is overheated? A crimped butt splice and heat shrink over is the only way, but it's best to replace the entire length with proper marine tinned wire, no splices. The black on the copper is oxidation and should be cut away. The oxidation is evidence of what a marine environment does to copper wire and the reason to use a tinned conductor. I know saving money is essential, but so is a running engine. Keep going, you're an inspiration for everyone.
yeep that is how i learned aswell ... too much heat can melt into a mess
Look into big battery cable crimpers and big butt joint connector and waterproof heat shrink like mentioned above. Solder joints will break over time and shouldn't be used in motor in vehicles.
Can you please say the word dingy ,at least once in your videos. For some reason I luv how you say it.
@@laurieherrick3654 + 1 on that! Or even more so: Make your mum say it when she´s on!
I would like to seriously recomend, you tab your bulkhead repair in with glassfiber mats and epoxy. Waves will send shockwaves through your hulls and I would think it is better to over engineer things. For the rest great job!
Yes
second this
Absolutely! This critical joint should have been scarfed, but taping both sides with biax would be better than nothing.
I totally agree. Such a bulkhead is load bearing and that repair needs to be BEEFY.
Third this !
I have to say " I have never seen anyone trying to clean the ends of old wire. Usually they just cut off the bad end!
Old tech here; When you are forced to clean copper wire to join, you can use H2SO4, Sulfuric acid in a dilute form. I usually just get a little acid out of a Lead Acid battey.
@@ebaab9913 can you use vinegar?
@@izzzzzz6 yep
In fact, the wires are not dirty. They are oxidized, and solder won't work without a very good acid rosin flux. You should have cut the end of the cables and started new or look for mechanical solder slices. Tyco or Raycheon should have exactly what you need. Remember, bad electrical connections are potential fire hazards
Acid rosin flux is another alternative, and vinegar does work, but not as well as dilute Sulfuric acid. The copper become shiny brite after treatment. I am an expert at soldering but would not have soldered that joint. I would have crimped it. I find that any movement in soldered joints can cause the fine wires to break off. I am in the electronic service industry.
Mark, I am afraid the comments indicating the bulkhead will pull away from the splice are correct. On the inboard side add a vertical tab say 150 mm that extends well past the part you added back in. You should go as far past the new material as you can. I would match the curve at the bottom so it will look like it was meant to be there. A good connection on the faying surfaces at the existing bulkhead will prevent the bulkhead buckling from pressure, and more likely, pulling apart when the part is in tension, which absolutely will happen. It won't even take a heavy sea at all to break apart. I am a former structural designer for a professional engineer, and I my experience tells me this needs to be addressed before leaving the dock. I hate it because your repair looked so nice, but you can reinforce your repair and it will look meant to be that way.
Great job so far. When you got the swamp creature, I thought she was actually in better shape than she was, but you had the vision to see it for what it could be, and you are turning her into a real boat. You have the gumption to back up and redo, and that is such an admirable attitude. I have so enjoyed watching your journey.
I pray he sees this comment and improves that bulkhead
Can he use puzzle joint in this place.
He ignores most good advice and likes comments that aren’t.
As an electrician I am a little concerned about your current wiring skills. Please use fuses next to the battery on the positive wires. And spend some money on some proper crimp terminals and connectors together with a proper crimping pliers. Seeing 15V coming from the outboard, this will fry you battery. So yes you might need a voltage regulator.
Don’t solder cables in a marine environment. The solder breaks down and causes loss connections . Only crimp and cover with heat shrink. I would recommend you redo these in the near future.
Agree
And there is a second problem: In order to solder such thick copper cables decently, you need to bring in so much heat that the insulation material will get burnt. This happens because copper conducts heat very well- you will literally heat up at least 10 or 15 cm of that cable in both directions in the process of soldering this connection. That's why most people prefer to crimp such diameters. But for that, you would need a better crimping device than what you used in this video.
Hotshrink should take care of that. And if you use a butane, it should heat up fast enough that it won't eff the insulation as much.
Agreeed Never Solder heavy wire like that. There is a dozen ways to join 1/0 for under $10 safely to last.
Ps. Your Engine is Not Overcharging. It is supposed to charge that voltage. 13-15v is normal and it will not hurt that battery or little alternator on the engine.
Recommendation for cables. Use tinned cable, helps prevent corrosion. Join cables with a crimped ferrule not solder and cover with heat shrink that has glue inside. The glued heat shrink will give a watertight seal.
Hey Mark, my second comment this week! The black stuff inside your engine cable means that water has got in there some time in the past. Unless you use tinned cable(and outboard manufacturers don't) water can wick its way all along the wire until it gets to a low point and then it slowly rots away the wire on the inside where you can't see it. My boat is now 30 years old and since i discovered this i have changed all my exterior wires to tinned and am slowly doing the inside ones.
Tinned is the only way to go on a boat!
How flexible is the tinned wire?
If you use a good marine tinned wire like ocean flex it's very flexible
You can dip the end in acetone. To clean before soldering and sealing.
Mine as well
Your occasional friends that show up for treats just make the videos dam near perfect.
Mark, first off great video as always. I’m an Avionics engineer in the RAF, so wiring and electronics are my profession. First off, the black cable ends need cutting back until clean cable is found. Second, I would crimp cables in an external environment, there are plenty of hermetically sealed crimps out there to choose from. Third, I didn’t notice in the video but where is your circuit protection (fuse / circuit breaker) and battery isolation switch to kill power in an emergency.You may have done it but not showed on the video.
As you wire more and more systems in to the boat you might be better going to a bus bar system now rather than later with individual circuit switching. I’m sure you aware of this though.
Hi Mark, i love your channel and i have a couple of suggestions for you. Number one is your mattress. Big chandlers sell a couple of different types of stuff which you put under the mattress to stop the moisture damaging it. You will still get water under that but if you regularly dry it out you wont ruin the mattress and it wont feel damp(and you won't get mould!) Also, i would either glue ply over the join in your bulkhead or what i would do, glass both sides with something like 2 layers of 450grm cloth and epoxy. Butt joints are not going to be strong enough. The good news is, you have done a good job so far, just needs finishing and fairing. Do it now, a gale at sea is no time to be worrying about it 😊
Yeah I agree glass matt past the joint 300mm both sides great job otherwise love the videos
yep, that would finish the job. that join needs to be a bit beefier.
You cut the bulkhead, now you need to fibreglass the patch to make the bulkhead strong again, do not compromise!
Copper is a very good thermal conductor & there is a lot of copper there, so that soldering iron was never going to cut it. I don't know which tutorials you've been watching but marine cables should always be crimped & on top of that its best to run the full length. To properly crimp any gauge you need the correct terminals and crimping tool. It's all standardized stuff. Any half assed job you do now, will likely bite you in the worst possible moment.
Your epoxy work looks better than many professionals I have seen. That is really really nice!
1. Bulkhead has also pull forces not only push. So you really need also fiberglass.
2. When soldering don’t rotate the threads just push them together.
3. Allways use electric tape first around the solder and then heat shrink. The wires will come through the shrink and create possible short circuit.
Scarf don't but joint use spoon for coving, tin your slder tip
dont solder in marine enviroments itll crack and u wont know whats wrong
Use some strands of wire to hold the spliced join together also.
Mark will know every square inch of this boat. HUGE advantage for a sailor heading out to the open sea!
When it starts breaking up, he’ll know exactly where he should not have taken shortcuts- ie; bulkhead.
In duck speak she’s actually saying “you’re family now.” 😂
You never 'clean' old wire. Clip it off about 5mm to 1 cm into the insulation, then strip the insulation off the unexposed wire. The reason you do this is because the exposed section will not conduct as well, especially in a marine environment. And by the way, this episode's soundtrack really works!
Yeah im on the fence about some of the other practices. Full lenghts no splicing etc. Cleaning the wires was a fopa to me. Just seems like bad practice to me.
The negative oxidation can extend quite a way up the wire. If it’s not going to be replaced I’d just clean and crimp it.
you can clean and then tin the wires. a bit of acetone will usually work. so long as you clean it well the flux and heat should finish for a nice secure soldered connection. heating the wire is vital. i will heat for a while then dap solder onto the iron to get it flowing, but once it starts, keep feeding solder onto the joint, not the iron. and heat shrink after.
@@sarahmanalapan8443I was trying to work out what “fopa” was an acronym for then realised maybe it was shorthand for “faux pas” - am I right? 🤔
That wire cancer probably goes 100mm up the cable.
Great video, including music 🎵.
Suggestions
1) purchase two marine batteries, one for each outboard - they can be wired each directly to a motor with no further regulation required. You then have two starter batteries which gives you redundancy. Wire your charging for the house battery off the starter batteries through an appropriate regulator that also isolates the house battery. You now have three batteries that each could double for starter or house in a pinch.
2) to guarantee bulkhead strength, epoxy a doubler on the back side across the patch and onto original bulkhead material - this should be easier and stronger than multiple layers of glass work.
3) find proper pretinned cable for your engine electrical connections as well as any future house wiring. Like your experience purchasing the used motors, you will not regret doing it right the first time. No splices unless absolutely needed. Only proper waterproof crimp connections. Your future self will thank you.
Mark from day 1 when I started watching you you have come a long way your doing great. Keep learning
Here in the US, they sell what we call "crackhead lighters" at most urban gas stations/tobacco shops, that can be used as a small torch to solder with.
Probably others have commented before, it’s been really cool watching your progression from a relative novice to well on your way to becoming a craftsman, of many trades….just a few….carpentry, fiberglass, coatings application, (sanding… maybe not a skill but shows perseverance), engine mechanics, metal fabrication, now electrical, soon rigging-project manager, materials sourcing, film production, editing. Dang. Good luck getting her sailing this summer! And Thanks!
That flat bladed vibrator (MultiTool?) you are using is one I have never (personally) experienced. I must be less than several decades old... I remember when the 'saws-all' was new. Hell, I remember when the 'SkillSaw' (not Circular Saw) was new...
I watch and I try to think that I could do something - nay ANYTHING - better than you and then I have to just settle back in admiration. How proud your parents must feel.
Thank you, kind sir. You are truly an inspiration.
Just a reminder.
The ocean is the most powerful thing!
It can crush and break things with incredible force.
Please do not expect some janky ropes and such to keep those motors in order.
First they will be pushing on your boat. Quite a bit of force.
And with the ocean in play and any kind of large waves wind and storms…
Please be sure to build your motor stuff solid and strong so the ocean will not simply crack it like a twig.
And figure out how you will deal with any motor emergencies while under way in heavy weather.
It looks so calm and nice water most times
I would hate to see you lulled into a false sense of security.
Make everything strong and try to do things they way they work best for you in the safest way your able.
Otherwise, fantastic videos great work
You go!!!
God bless you
Mark. If the wire is fixed in place. Get some copper pipe tube and different sizes. You can make lugs. Strip your wire a bit longer. Crimp in the copper tube, then use a butane gas torch and then insulate with multiple heatshrink. You're sailing the world, you do not want to be looking for an electrical fault. It takes 4 times longer to find and repair. In a high sea you do not want to be doing.
Yes, soldering is a better connection, when you know what you're doing, you don't. Highly corrosive environment will quickly evaluate your work.
😁😁😁 Those talking ducks are so funny and cute. Great idea. 👍👌👏 First time I heard about Weetabix was in one of those fantastic Wallace and Gromit cartoons many years ago.
Thank you for posting your work. There are many good ideas in the comments, but one I believe you should do is the wiring. Please use crimp butt connectors with heat shrink. ABYC is a course that I am currently taking for electrical. Solder may crack with the movement of the boat. Also on your batteries always use nuts never use butterfly (wing) nuts. They can come loose very easily. Also place a cutoff switch(on/off) between the batteries and your motors and don’t forget the fuse. One of the most reasons boats catch fire is because of electrical. See if you can get a copy of Nigel Calder book Boatowners Mechanical and Electrical Manual. Keep up the good work. I enjoy watching your progress.
The music you play is always fine and the level relative to when you're narrating is perfect, unlike so many YT channels where the music is WAY too loud.
You are a breath of fresh air to those that are struggling with boat repairs. I have spent 6 1/2 hours trying to get my horn hooked up on my current boat. I told my partner that it should be about 20 minutes. I'm learning along with you.
Mark, it's a pleasure to witness as your woodworking tool skills keep improving, well done! My favorite part was the coot (and her chick) who know that you have not only good food on board, but also a kind heart to share it (and also storytelling skills to make this episode so much more damn charming). :) Lee
Hi Mark, I'm really enjoying following your progress and the way you communicate, thank you 👍
A bit of input from me on your batteries, if they're deep cycle 12v lead acid batteries, each 12v battery can float happliy, continuously on 13.6v
"This voltage will maintain the full charge condition in the battery without boiling your electrolyte or overcharging the battery"
If you're maintaining over this voltage, I suggest you regulate the input voltage.
Another tip is a thin smear of petroleum jelly (from supermarket) on any exposed metal of the battery terminals and clamps. This will help control corrosion.
Cheers,
Dave
Your getting there Mark, little by little bit by bit. You may think! it's all boring to you due to the fact you think you haven't made much progress nevertheless I enjoy watching whatever progress you make. so don't be so hard on yourself, at least you got a video put out, so that we could have something to watch. LOL
I don't know a thing about boats but, I love watching you and am learning so much. I was wondering about using fiberglass tape for that work you just did. Now about your music. I only wish that all RUclips sites had the music you have. Hands down you have the BEST selection of music than anyone else. I look forward to listen to it every week. I only wish I knew who all the music was. Great job on the boat.🎉
The advantage of knowing your boat so well, will be the advantage on the high seas, then you'll have the gear to fix it on the fly! Can't wait to see you sail!
I have been following you from the start of the build and I think your dedication to this is amazing! I feel that I have to comment on the repair you have made to the bulkhead. Please let me say from the start that I'm not a qualified engineer, but I have made a lot of things and it seems to me that the depth of that bulkhead says something about the forces it was designed to withstand and as such it's quite deep. I'm presuming that from an interior design perspective there would be no reason to protrude into the internal space for any other reason than to resist loads on the hull. Given that water has a density of 1 ton per cubic meter and given the size of the hull, I would also presume that the forces acting upon the hull could be quite large. Your repair looks really nice and I don't want to be critical in any way, I just feel duty bound to say this as the failure along one of the glue joints in the repair while under heavy seas could lead to the stresses induced to be put into the hull. This would obviously be very serious. I would think a fairly cheap and easy solution would be to glue and screw a strip of aluminium half round section along the front of the bullhead, thus transmitting any loads through this rather than the glue joints. I hope I have come across as trying to help rather than being critical as helping is my only intention. Thanks for the great videos!
You are being very modest here. This "repair" is potentially fatal. I would glass both sides with 2 layers of 450 g.m.2 biax overlapping both sides 12* the thickness of the bulkhead. Ideally it should be calculated properly but these butt joints will not hold. I've seen plenty of snapped epoxy joints that were not scarfed 8:1 or otherwise sistered in or sandwiched. Mark, beware!
Dude you are the Captain so you decide Everything.. What's happening on the Mahi and Everybody has to listen to the Captain.. Aye aye Skipper we love your hard work...
Your boat is coming along so well, it's very impressive!
Using the battery you run the boat off as a starting battery could bite you in the arse. Better to give your engines small, cheap motorbike batteries with a voltage regulated relay to allow the engines to charge the boat battery when the engine batteries are charged from starting.
As an Old Jazz drummer…your choice of music is always the best! Cheers
I kept thinking of the Fast Show - Jazz Club with Louis Balfour...
Absolutely love the musical background ❤❤❤
I assume you are in contact with Hanekke and she will let you know if your Mahi is getting proper treatment.
The dirty tarnished black cable might be in better condition if you snip the end off and trim back the plastic sheath. It all depends how much corrosion has taken place.
It;s encouraging to know people and companies are helping. You're doing gr8.
After a rainy day working in Cornwall good to see you had put a video on enjoyed that thanks
Jazz and Bebop is your thing! Don't go changing. Love this channel and your style of narration
While you may not have saved any money with the used outboards you gained and enormous amount of experience and that is invaluable! You know them inside an out and when you have an issue far from anywhere and everywhere YOU will be able to competently and confidently solve it and get going! Not to mention the quality time with Dad- that is also invaluable!
I really like the honesty in your videos. You’re quite happy to share your cock ups with everyone. You’ve been on a massive learning curve and there are always people willing to give you advice (some good some bordering on the nasty). Stay true to yourself and your dreams will come true soon enough. Hats off to your parents. Andy on the wonderful Island of Alderney. Come visit us when you can.
You're doing a solid job, keep on keeping on.
Hammock is the only way to go for me. Once you hang on a rocking ocean, you'll get hooked 🤙
Really glad to hear you say you will be getting a single cable from your engines to your battery. Talk to the people that you got that indoor battery system from. They can help you in setting up different battery banks for the uses that you will need. Other people have said this, and I’ve been holding my breath/response. Epoxy is not strong by itself. You are using it like glue. Epoxy needs fiberglass to get its strength. There are multiple kinds of fiberglass that work for all types of different situations. Do the research online to figure out what is the best fiberglass for your individual uses. I know you’re in a hurry to get sailing. In the long run, it will be cheaper to only do things once rather than have to fix things you’ve already spent time on.
Connect the alternator to a charging system and tie it back to your boat power. Then trickle charge your starter off the boat power. if it has enough cold crank amps it should start both motors.
forget about soldering on a boat. check the max current and get a decent connector for that with a waterproof silicon box.
I recommend using shrink wrap tubing to seal all the connections and splices. I used to use that to repair the wiring on bug truck trailer lights exposed to four season weather and road salt.
We'll have to start calling you Dr. Dolittle....loved it.
Great to see the good progress Mark. Getting ever closer to sailing!
Shame about the music. Normally it is so bad I have to turn it down. This week it was worse. Had to turn the sound off completely.
Lots of 12v portable refrigeration products on the market these days. One of those would be easily handled by your power supply. Presto all the ice you want and keep the groceries cold.
Things are starting to come together you have amazing mum & day keep it up great job
I think I'm saying this every week, but none the less, it is so good to see you are going the extra mile to make things right, even if it means you have to do it twice....by now you have also gotten to the place where you know if something doesn't work well, you can always cut out the offending work and do it again...keep up the good work Mark...cheers
You’re doing a great job Mark
Mark, You need to flux the crap out of those wires and the solder will sweat into all the nooks and crannies.
22:12 - yes, a DC to DC charger that detects that the engine is running - per engine. Something like a couple of Victron Energy Orion-Tr Smart Isolated DC-DC Chargers would do the job. Not cheap, but neither are buggered batteries when you need them most.
Lots of great progress.
As for the soldering. Sorry, but that wasn’t good penetration. You should actually see the solder being pulled into the connection.
The first shield you were using was for heat shrink.
When making the butt connection, don’t splay the wire like that, just wiggle the connection together. It’s a tighter connection and a cleaner look. If you have a flux, just push each end into the container before pushing them together. Also, what I like to do, I take a waste 150mm section of wire and strip it down. I then take a single start and off the wire, and tightly wrap it around the section to be soldered.
Since you have a gas soldering gun, I would use a bare flame to heat up large connections like that. I would then apply the solder from the side away from the flame. You want the copper to be melting the solder, and not the flame. A smaller gauge wire would be so much easier.
I was a communications tech, and in close to 10 years of work and thousands of connections, I never had a single failure using that technique.
If you’d like, I could make you a tutorial video, and email it to you.
What you did will work, but it could be much better. I’m not trying to just be critical, I’d like to see you learning a better way.
When you been been hanging for a wildings fix!
Amazing work over the year -- it's been fun to watch -- and, as always, love the jazz and your cutaways to local wildlife❣
Try using a file or sandpaper to clean the muck from the tip of the soldering iron. Works like new afterwards.
Mark, wow those engines are humming! Great job on splicing in the decayed frame, should be solid. Love your channel, so informative and full of valued information. Best with feeding the ducks!
take the tip off the solder iron and clean the tip and screw that hold it. then heat it up and melt solder onto the tip and quickly wipe with a rag. that's how you get the iron to work like it should
Mark in my opinion you should get a proper marine electrian to wire everything up
Thanks for your efforts, Mark. We deffo appreciate the 4k content!
Your epoxy skills have improved tremendously. 👍
Determination grit and skill in abundance in this fascinating sea saga of resurrecting a yacht.The whole family came together in this tremendous effort.Well done.
Rather than joining the cables, I think I'd have bought new lengths the correct size.
It may have been cheaper than buying multiple soldering irons. There is a reason why on boats and even aircraft, preferred method of connection is ALWAYS crimping.
Another hint, thru hull fixtures for cables are very seldom water proof. If ever.
I would think your alternator would have a regulator to avoid over charging.
He needs bakers soldering fluid to make it better
Cheaper is seldom the least expensive. I think you mentioned that in the beginning of the video referring to your outboards.
If that black is all the way into the cable it needs cutting back or replacing.
Get rid of any termite wood they will spread
I am doing nightshifts on the weekends and I am always looking forward for your videos. ❤
On the patch in the bulkhead at the chain plate, if you run a piece of wood on the edge like a small T, it will be much stronger and less chance of cutting you when you bump into it.
Love the Jazz, keep on keeping on.
Hi Mark. You're becoming a great hand at the Carpentry, nice job bro. I know nothing about electrics but I wish you well mate. She is coming along brilliantly. I can't believe that it's been a year since you first saw this boat, and you were stuck in that crappy pond, lol. What a difference a year makes. Keep it up, Mark, we are all egging you on over here in Ireland. 💯👏👏👌🇮🇪
It’s nice to notice how you continously make progress with your boat and with your competence! However, there are always pitfalls. RUclips is an awesome source of knowledge, but also can be wildly wrong. About joining the cables with solder: That’s NOT a good method. Loads of people think it is. They are dead wrong.
Copper is a great conductor. Tin is an OK conductor. If the current flowing through the cables is anywhere approaching the capacity of the cables, the tin will have way more resistance than the cables and it will get hot. Hot tin melts. The cables are no more connected…
Even if this problem doesn’t happen, the solder will stiffen the cables, creating a weak point for fatigue. Your situation isn’t vulnerable for that, since the solder is in a loose hanging piece, not off a fixed point, but useful to be aware of. The right way to connect or terminate cables on a boat, or any other installation with movement, is crimping, press fittings. If you use the right terminals and a good crimping tool, the metal gets compressed enough to cold melt it.
That’s copper “melted” onto copper. Full on contact. Minimal extra heat. If it’s heated, it’ll stay compressed. Not loose contact. Some like to use solder to seal the press fitting from moisture. I think it’s ok, as long as the solder is added AFTER the fitting has been compressed, but I think a heat shrink sleeve with glue inside is better. You have a small and simple electrical system, so your soldered cable connection will probably last a long time, but the right solutions are still better. Deleting problems before they happen is always preferable.
By the way, I also live on a catamaran, in Amsterdam…
When soldering like said previously, generous flux, Feed solder on opposite side from heat and the solder will run to where heat is applied, pull heat away when solder flowing close to where you want to end, clean off flux with some dishsoap/dawn and water, wipe dry and. It will shine. The flux not cleaned off turns/oxidizes green fast.. maybe not so fast if air tight though.
Your doing good for so close to D-day!
For splicing wires, you have to check out MIT’s guide. It’s the gold standard. ⭐️
You can get waterproof junction boxes with heavy duty posts so you solder rings on the cables and crank them down tight.
"featuring Clam, on bass......nice"
Look out for those blue plastic mushroom crates that supermarkets/takeaways use. They make a great air space under a mattress to eliminate the condensation problem.
a small torch can be used to heat the wires when they are that large just be careful not to over heat :) and a copper barrel can also be used with the solder for the connection You are doing great Keep it up !
The music in your videos reminds me of Christian Williams and his sailing videos.
And yes, you're cooking those batteries at 15.5V
I enjoy watching you learn new things. Your names for some things are funny. Your doing a great job!
(IMO) The beebop fits your editing style better than the surf rock. The faster style adds to the hurried pace of a sped up clip of you working. However, I'd still watch your vids no matter which genre of music you use as backing. Hope your PC woes are all over!
You need a split character controller, your battery can boil if over charged ❤
Dude, your killing it. I love the “ summer solutions”. I think your right about the bulkhead repair. I would be very surprised to see a fail there. Cheers
Mark that's a great little gas soderer you have, I have the same one. Use it like a heat gun/hair dryer (without an attatchment) on the shrink hoses, holding it just close enough, and not the side of it's shaft. You also won't need to use your lighter and risk burning your finger/thumb any more. See you in the nxt1.
Some good comments to read there Mark what a great way to learn, the thing is mate your not the only one learning here, we do to and really appreciate the advice from people all over the world the knowledge is definitely universal cheers mate
It's looking up brother can't wait to see your first sail out to sea ⛵🌊⛵🌊
Looks great, Ben. You're doing a fine job. I am really enjoying the music. Also, when soldering, don't be stingy with the flux.
Great progress on the boat ! She's looking very nice. 💖👍
I understand that Banks in Hoofddorp , Netherlands are closing down. Keep your ears open to info so your not caught unexpectedly without funds. Things are getting touchy world-wide. Take care. 🤗⛵🐬🐟🌎💖🇺🇲S/V Cork ~
Texas.
Your doing great!! Early on when you were shopping I prayed you would get this boat, knew it would be a great journey for you.
You keep researching the tasks you wish to achieve, doing the next right things looking out for your future self paying it forward. You will know everything there's to know about your boat when you are done👍😌🌠all blessings your way.
Yes, back to filming 👍 Great update 2x👍
You are one of my 2 favorite sailing channels. That said, if you got a nickel every time I said "Gawd I hate smooth jazz.", while I watched this, you could be running 2 brand new Honda 9.9 4 strokes with extended warranties. Every other kind of music, almost, even obnoxious jazz, (like tape 5) I don't mind, at all (love those guys, actually). However, it would take much worse things than elevator music to keep me from watching, liking, and sometimes commenting encouraging things on your videos. Keep up the good work. You are a credit to your generation. Just, smooth jazz makes me feel violent, that's all.
The aqua paint job on the hulls is beautiful. Paint the yellow white and she will look lovely. Keep up the good work mark
That wood work turned out great. When you route the cable on the outside try to have them track lower than the gland, that way water will track away from them :)
Well done you even your dad must of come across things in the beginning that didn’t go completely correct but you master them just like him well done your effort is great mark never beat your self up because your learning the knowledge as you go along I think anyone looking knows that and I’d say all proud of you a good hard worker well done I’d say keep it up it’s so interesting ❤
What you used to solder the large wires together can also be used to heat the shrink tube. I think you will like the results.
Great music! Thanks for keeping us in the loop. Love seeing your progress.
As others have said youll need to use glass matting to strengthen that bulkhead. It wont hold up in open seas