Installing a light bar on the quad,
HTML-код
- Опубликовано: 13 сен 2024
- In this video I’m going to install a light on the Yamaha yfz 450, but the installation could be similar with any quad. if you enjoyed the video give it a thumbs up.
Follow me on my Instagram.
/ custom_autobuilds
The quad looks sick
Thanks ✌️
Do you remember what color wire was the high beam ? Thanks
green
Man I miss my YFZ…. Looks great man
Has that Ebay light lasted? Do you like the quality of led light? No issues with stator? Thanks 🙏
Yeah so far so good, when I buy I don’t go for the cheapest one, and I check to make sure there is good reviews
So I just get the red and black wire and twist it with the ones I have on my yfz or raptor head lights or..?
I need help wiring it up bro !!! Please help me also bought a ridgid bracket
What is the name of the led bar? How long is it?
Where you still able to turn left and right hood after you cut the bracket on the sides?
Yes it fixed the clearance issue
How much lumens is the light bar is it bright at night
I have yfz450 also.
Same
Nice bike
No quema cuh
How did you connect it to your head lights?
I am trying to do exactly what you are. Did you have any problems with it pulling too much power from the battery and if you could tell me which color white you hooked up to what
I meant wire but also did you wire the light only to one of the stock lights
where did u get the bracket?
What size is that light bar? U have a link?
What size is the light bar ?
Merci mec👍
What’s size light bar?
Could you make a video on how to connect it to your headlights? Or give me a step by step in the comments😀 I just need help with the wiring red and black from the light bar to what color on the head lights and how do I do it?
Power (red) to green (high beam) , black to Ground on bike someplace or ground to ground wire for headlight.
fourrrfittyyyyyy
Do you need fuze or not ?
I never put fuze on LED lights
when installing a "Bare Bones" i.e.. installing your own wires and on/off toggle switch, its recommended to use a fuse and a relay switch. When splicing into your existing wire harness, typically a fuse and relay is already part of your lighting system (from the factory) so tapping into the existing "High Beam" hot wire should be fine. Just know, adding a fuse is adding protection... So ultimately IMO a fuse is a good is idea.
Where did you Get that light bar from ??
eBay
@@customautobuilds712 whats it called
Can you put the link to that led bar
regular 10 inch led bar can't tell you anything specific
How do I connect the light bar to the headlights? Please pleas let me now asap
Wire bar to headlight wire
@@customautobuilds712 but how bro the red cable from the light bar to what wire and the black wire from the light bar to what wire on the headlight?
@@customautobuilds712 and how do I connect the wires from the light bar to the wires from the headlight
Try positive red to red black to black all it is is running a currentthrough the light
I tried putting the wires backwards and the light still works so doesn’t matter but if they’re color matched then match them by color
where did you get that bracket?
Greg Hayes I pulled it out from my old quad, I bought that quad with a bracket
Looks like a rigid industries bracket
How did you connect it? I have red and black on led bar and yellow, blue and black on my quad beam.
Need to know too
@@JoseAngel-xb5ww I think I connect it to the black and yellow and the led bar is activated when I turn to high beam. I'll make sure in few hours and get back to you.
the RED/BLACK on the LED Bar is... : Red = "Positive/Hot" and BLACK = "Negative/Ground". The Yellow/Blue/Black is most likely Yellow = "Low Beam" - Blue = "High Beam" and Black = "negative/Ground". ***refer to a wire diagram for you specific bike*** But if this is the case.. Black to Black and Red to Blue (Blue Or Yellow... depending which one is the High Beam Hot wire").
@@mrmgjohnson and how would I do this just twist them together?
@@mrmgjohnson could you give me a step by step if you don’t mind 😀👍🏼 would appreciate it