I see you are trying different types of rotor...this one seems like great efficiency... I did same turbines ..i did about 60 types...and the best result was one with 2 discs and only 12 blades 35 cm.diameter.blades are long so they overlap each other about 3 cm.and they go down only 3 sm from outside radius to inside...wow you will be amazed how efficient that will be... basically steam enters turbine uses Ventury principle and grabs 6 times volume inside turbine and then all that exits through all 12 exits...again diameter was 35 cm. 3 cm thick..3 cm overlap and 3 cm incline from inside diameter to outside diameter.... Try Cheers from Ukraine
This is a real inspiration, it didn't take any super high tech to create something like this! Can you say how much power in KW you are able to get out of this?
Balancing will be easier if the blades are trimmed so they all weigh the same. Then your concern will be getting the welds as close as possible to identical. The discharge should be directed to a condenser and recycled since it's basically distilled feed water. As for pulling a vacuum, you'll need labyrinth seals on the traveling edges, but the performance gain will be obvious. It was nice to see you actually using steam instead of compressed air as so many online seem to do.
Yes, you are right, the balance of the system is extremely important, and the use of steam serves a specific purpose, and that is the construction of a unique home power plant. Thank you for your nice comment
@@fixedfocussolar No problem, steam is a serious force and a turbine is the best way I have seen to get every calorie. But the overhead is high and your water processing has to occur on the fly. Since you are discharging from the center you could run the discharge steam/condensate through another heating loop and then into a low-pressure turbine. With your form factor it would probably work better like stairs, HP on top and LP below and then feeding into a condenser. I'm speculating because I don't know what pressure or temperature your steam is arriving. Another advantage to your design is that you can add additional steam nozzles and feed them as the load increases. It would also be a way to throttle around speeds where the dynamics/balance transitions. Steam is a cruel mistress though. So keep the joints tight and lag/wrap everything when you've finished tuning.
Make a whole power generation system with those parabolic mirror to make steam connected to this turbine to generate electricity. It will be good for residential usage .
@@fixedfocussolar Нет -это рац. предложение ,улучшить - усовершенствовать устройство На Турбину установить Супер Маховик Работы советского физика Гулия Или два Маховика в Противо Ходе Это умножит скорость эл. генератора Сам Маховик мех. Аккумулятор ,а его инерция - смягчит рывки и вибрации ...
Sir someone has hacked my son Muhammad Awais channel " Awais talent"for various science models a few days ago.sir what should be done to restore the channel.
Great informative video about steam turbine building.
Thanks dear. Keep up the good work.
Thanks a lot
I see you are trying different types of rotor...this one seems like great efficiency...
I did same turbines ..i did about 60 types...and the best result was one with 2 discs and only 12 blades 35 cm.diameter.blades are long so they overlap each other about 3 cm.and they go down only 3 sm from outside radius to inside...wow you will be amazed how efficient that will be... basically steam enters turbine uses Ventury principle and grabs 6 times volume inside turbine and then all that exits through all 12 exits...again diameter was 35 cm. 3 cm thick..3 cm overlap and 3 cm incline from inside diameter to outside diameter.... Try
Cheers from Ukraine
Thank you for your guidance
This is a real inspiration, it didn't take any super high tech to create something like this!
Can you say how much power in KW you are able to get out of this?
Balancing will be easier if the blades are trimmed so they all weigh the same. Then your concern will be getting the welds as close as possible to identical. The discharge should be directed to a condenser and recycled since it's basically distilled feed water. As for pulling a vacuum, you'll need labyrinth seals on the traveling edges, but the performance gain will be obvious. It was nice to see you actually using steam instead of compressed air as so many online seem to do.
Yes, you are right, the balance of the system is extremely important, and the use of steam serves a specific purpose, and that is the construction of a unique home power plant.
Thank you for your nice comment
@@fixedfocussolar No problem, steam is a serious force and a turbine is the best way I have seen to get every calorie. But the overhead is high and your water processing has to occur on the fly. Since you are discharging from the center you could run the discharge steam/condensate through another heating loop and then into a low-pressure turbine. With your form factor it would probably work better like stairs, HP on top and LP below and then feeding into a condenser. I'm speculating because I don't know what pressure or temperature your steam is arriving. Another advantage to your design is that you can add additional steam nozzles and feed them as the load increases. It would also be a way to throttle around speeds where the dynamics/balance transitions. Steam is a cruel mistress though. So keep the joints tight and lag/wrap everything when you've finished tuning.
Good idea
Thank you dear friend
Like a larvel turbine 👍
De Laval
Almost but with one rotor
👍 👍
Excelente, cuando puedas nos regalas un vídeo, pero con una turbina pelton. Felicitaciones
gracias querido amigo
Good information
Thanks
Make a whole power generation system with those parabolic mirror to make steam connected to this turbine to generate electricity. It will be good for residential usage .
Dear friend, I don't know why RUclips doesn't show it, watch the video below
ruclips.net/video/30bUUWKHrII/видео.html
@@fixedfocussolar - Thankyou
Thank you!
Welcome!
Thanks I'm gonna build mine sooner
Thank you and good luck
Супер Маховик - Аккумулятор и Амортизация
привет
Почему вы думаете, что это был Супер Маховик?
И структура турбины другая.
@@fixedfocussolar Нет -это рац. предложение ,улучшить - усовершенствовать устройство
На Турбину установить Супер Маховик
Работы советского физика Гулия
Или два Маховика в Противо Ходе
Это умножит скорость эл. генератора
Сам Маховик мех. Аккумулятор ,а его инерция - смягчит рывки и вибрации ...
nice. introduce a condenser to recirculate the water and you have perfect system. the rpm you got is so good man
thanks for your attention
عالی
ممنونم دوست عزیز
I recommend a tesla turbine maybe this is interesting enhanchement for you
thank you
But unfortunately Tesla turbine is not suitable for steam
And if it was suitable, the steam power plants would use the Tesla turbine
Where is steam out pipe?
Large hole in the center of the turbine
How much electricity can be generated from this?
It depends on the manufacturing accuracy and the amount of steam injected into the turbine
For example, from 200 watts to 2000 watts
@@fixedfocussolar - I mean how much volts for 44693 rpm as he shows in the video. I don't the torque value here
Hello! What the power in kwt this turbine?
The power of this turbine is high and it can even reach 10 kilowatts, and it depends on the amount of steam and pressure applied.
@@fixedfocussolar Thank you for the answer! I will follow the updates on your channel! Subscribed!
Sir someone has hacked my son Muhammad Awais channel " Awais talent"for various science models a few days ago.sir what should be done to restore the channel.
I don't think anyone can hack someone else's channel on RUclips if the deleted channel is deleted by RUclips itself.