Видео

It’s weird how everyone calls the throttle pedal a gas pedal when the throttle opens up for air not fuel lol

those msd wires still holding up? im looking into getting the headers and the entended o2s, wires and the sparkplugs and sleeves.

Tuning??

Did you tune out the rear o2 sensors?

Pedal commander. Is a cheap pos made in turkey . Watch banks videos on the Comparison of pedal commander to thier pedal monster . Big difference between the two and pedal commander falls short of saftey and reliability , biggest saftey hazard with pedal commander is if it fails it kills your pedal completely. DO NOT BUY A PEDAL COMMANDER

Are you in Charleston by chance? I almost bought a truck identical to that, lol. Also, if you are in charleston, what exhaust shop did you go to?

Does the speed engineering headers and y pipe have 3 or 4 o2 sensor ports?

Just did that ground, and it took 5 mins. You have to have a ratchet wrench with the head that flexes.

How much did the whole setup run you? Could you give me a list of everything you purchased, I want to do this to my truck lol. What did you use for your exhaust setup?

Will the OE upgrade rough country control arms fit a 3/2 level kit ?

Love it dude

Sounds beast!!!🤣🤣

I've heard if you wipe down the headers with transmission fluid before installing them they won't rust . I have a supercharged 6.2 chevy Reaper truck I'm thinking about installing long tubes . Great video !

Did you get 10’’ or 12’’ spark plug wires ??

How the drone in town and highway

why does your truck say fuel economy last 31 miles? my 15 sierra says 25, 50, and 400 . i thought 31 was odd

did you just buy the headers and it came with the y pipe kit or did you have to buy the y pipe kit too

What headlights? I just bought my first car, 2016 ford f150 5.0 sport fx4 and I love your wheels, exhaust, headlights!!

Update on amp ?

Get dirt king cams and you don’t have to worry about alignment

After 30,000 I think the ball joints are shot.

is the extra pipe you installed a 45 degree or a 90 degree??

One question not related to this but to a video you made that I watched to install my fog lights I was wondering how you can re aim the fog lights ?? Mine are pointing down and don’t know how to make them point more up

The exhaust bolts break off as they weaken due to constant heat cycles of the engine and from side to side motion of the exhaust. When the exhaust sways side to side the bolts are pried up from the block. They will stretch about 1-1.5mm, and after that the head just pops off. Sometimes it seems like the heads broke off when you go to remove them, but in reality they are already broken. Depending on which way the exhaust swings, the bolts at the front or rear of the block will stretch first. Replace them every 3-4 years, as it is not a matter of if, but when. Every time you drive your car the bolts get a little bit weaker. It didn't help that in 2014 the factory flex pipe was removed.

I'm looking for a new setup for my F150 and I think this convinced me. Great looking truck. I may have missed it in the video, but what tire dimensions did you end up going with? Keep up the great content.

I had he'll of a time with my GMC 1500 Sierra. Could not get the top bushing in place.

Check engine light on, reason for that?

Looks great! A whole new look. What offset did you run? They poke but not too much.

What was the mileage ?

Sounds amazing doesn’t even need headers

What is the link to the stension sensors conector i have chevy silverado 2014 bro

Perfect Thanks!

Don't buy the Dorman! Its not a full kit. That is why he had to remove parts and install on the new manifold. The correct part # FL3Z9424J DORMAN isn't a full kit!! Buy the ford part #

This guy has to stay up north

So you’ve deleted all 3 cats now?

Stupid question but I'm buying some methods this Sunday off of Facebook and don't see a bolt pattern for center caps, does that mean I can only get the ones plastic flush ones?

What is the offset on the wheels?

Did that ceramic kit come like that or you bought everything the stuff separately? I’m looking at getting these same exact tips

I just got mine today glad i pulled the trigger on this product great video my friend.

is that an Odelphi headlamp? I have one and love it. I've had several cars with sunroofs and seldom use them, but I've learned that most of the time they break from not using them. The motors seize up and the plastic parts seize and become brittle.

Go ahead and change that ac belt brother(maybe)

What’s your wheel and tire set up?

What’s the wheel set up bro ?

Those welds are awful

I have the same setup on my 14 Silverado Borla Atak Dual Exhaust. Shes loud as fuck. Id definetly invest in getting it tuned. Mine was running super lean because of the Long tube headers. After the tune. It definitely woke the truck up even more.

Did this give a check engine light? Or error codes on sensor

Whats the wheel and tire set up? Method race wheels? Curious bc they stick out of the fenders perfectly not to much is what im looking to do with my truck

6:45 mark. Why do you show an hour trying to get the trim off and 10 seconds showing how to cut and fit 😢

Does this for sure fit my 99 gmc?

whatever you think of your own method or result.. it still saves us newbies from guesswork and learning by experience. I think you did well!