Видео

Which is better, ESP32 version or Pi Pico 2 version?

S-ought-ering

Hello. Great Video. Eye Opener. Thanks. For the Battery Hack I have a suggestion : The USB uses the two data lines (TX, RX) but there are the two power lines +5 and GND. Make and "adapter" cable, male and female, bring out the the +5 and GND and connect them to the external Power Supply, and pass through the two data lines as they are. The phone will normally charge while running.

I only motorola or samsung use, made in china = future problem. Install TWRP, CustomRom (like CrDroid) and rooting, after install apk: firewall, vpn, - root phone is super vpn router and only linux phone better.. my movie from POLAND...ruclips.net/video/8WyJNxk-K30/видео.html

Forget about Raspberry Pi and look at this very simple IOT project. Really N*gga?

5:16 love the 70s cop show music. Who loves you baby?

Good use of Phone mobile as Raspberrypi

Can I ask for a 3D file of your car frame?

Nah... just buy esp32 and stop overthinking...

You cannot compare raspberry pi with phone, phone is just a toy to control pair of LEDs

I did another round of experiments this past summer, this time using the cathode as the signal input. I still used a high negative voltage bias on an external foil cap/grid, but otherwise the setup was similar to a grounded grid configuration. Again, I only used bulbs with a high enough vacuum to exhibit cathode-ray/bremsstrahlung effects. The results were more reliable but otherwise similar to a common cathode approach, with voltage gains between 1 and 2 easily achieved for audio band signals while passing several hundred microamps of emission current. The output waveform was often distorted at the highest gain, showing frequency multiplication or division, or even breaking into very high amplitude relaxation oscillations. The settings are critical, and if it falls out of operation, all three biases (plate V, grid V, filament I) may need to be "reset" by bringing them back down to zero before finding the new point of equilibrium. This sort of behavior is typical of early gassy tubes, and part of why external grid tubes were never a commercial success. I intend to try using one of these bulbs as a radio detector eventually, as it will undoubtedly work as well or better than a diode in a primitive AM receiver.

اذا شركه سامسونج شافت الفيديو راح تشنقك

I was introduced to the 555 in college in the early 80's. One teacher was obsessed with collecting 555 circuits. You made some great practical 555 circuits. The parts combination in the 555 was just perfect. I wish SOC's had a few 555's built in that allows the flip flop to be reset.

The battery supply part alone was worth the watch

Use a centrifugal fan blower module to blow directly on motor

Das klingt mir zu deutsch

nice subed thumbed

Nice video. I actually use old phones to watch movie in bed, but I also use them as my TV remotes, usually by casting content seamlessly across the network. With a vnc my phone becomes a wireless print server for my wireless printer. The list goes on...

A small correction. Capacity in either Wh or Ah is power multiplied by time or current multiplied by time. We say "Watt hour" or "Amp hour" not "Watts per hour" or "Amps per hour" (which implies division).

How can I buy circuit boards designed by others that were made by PCBWAY? I used a 555 timer to pulse a solid state relay, 150ms on, 1000ms off. I used it to test 120vac traffic signal wiring circuits, I could adjust the on and off durantion as needed.

Great project I starred and goig to use as a startup for mine. Expecially for the electronic part. Question: is not possible to decode directly the analog I / Q signal using GNURadio, with Audio input block?

I'm just beginner. I noticed your code has bit shifting and bitwise operation and I never understand how it works. Do you have some simple tutorial on how to use it? I understand only that it move bit left and right but never understand how it is used on the data.

I don't know why, but now I want some Schnitzel and beer at the Oktoberfest.

*I made a very powerful cell phone jammer using a 555 and it even does the new G6 by driving a crystal.*

you're smart

Thank you.

What type of stepper motor are you using?

What parameters does this stepper motor have?

I did not know that a 555 could be used as an audio amplifier. Very interesting! Is there any particular advantage to using this?

Simpliously Fantastic

gut gemacht...bravo!!! bravo!!! bravo!!!

Can I edit its OS for more deep access?

Mmmm, ok, im not ready for this, i better google what a 555 is, not the Korn song, if your 555, then im 666, terrible song

Is this video for some forest people ? or just indian "inventor" ? 💩

Nice 555 applications. When I was a student I built an astable oscillator with 1 diode instead of a resistor.

I just bought a nano 9k and this is an amazing video! Nice editing. Thank you for teaching me I really want to master fpga

All my old phones have a purpose. My old destroyed S8 acts as my power efficient Desktop (I overclocked it too), then my old Galaxy S5 acts as dashcam in my car. I got more ofc.

i am looking for a remote control.🙃

The 555 is a very useful IC.. I used it a lot when I was an EE undergrad and later. It's good for simple projects. However people move on and the 555 gets left in the dust. A couple of times I have met people who use the 555 for everything they do. I guess if the 555 is not suitable for a project, they don't do it. Not good to fixate on one way of doing things.

They make a real good power mosfet gate drivers too.

As an amplifier, it seems to sound quite good. The speaker would sound much louder inside a small enclosure.

The 555 must be the most successful IC, and one of the oldest, together with the 741.😊😀

WD40 in DIP-8

What those yellow spots on the wire of the schematic is for? I never saw such an ugly drawing!

How can I get more GPIO pins or how can I control more like motors, servos, or any other modules

Can you share the apk file somehow

Phones running the mainline linux kernel with a distro like ubuntu/mobian replaced the raspi for me years ago. My oneplus 6 has 8 cores 8gb ram 128gb ufs storage no pi can compete against that

Install mainline to it and use the vibration motors gpio to a gpio extender ao you have native pins and controll over the hw from the phone

I was thinking about this in a slightly different way. I would think that it is possible to use an old phone as a graphics card or other add in board via PCI and increase the utility of the host computer and the phone and it's parts not used inside. A separate screen output? A security camera or something else? A OBD 1 or maybe even 2 replacement ECM for a car? And things that I haven't thought about, I'm sure.