Видео

i got one today and it looks like yours / great stuff

Where's the oil pump. Even with the spark plug out I can barely turn the fly wheel. It's sound like metal in metal. Suspect oil getting inside to lube.

i'd be interested in your rationale for 1: re-using the original smaller outside diameter top-end washer instead of the newly supplied larger one and 2: how do you decide between replacing the entire three-legged mandrel assembly vs just dropping the spindle shaft assembly out and replacing just that? i've been unable to remove the lower bearing off the shaft so i've had to replace the entire spindle when i only had the the bearings starting to go - everything else was still in working order. any thoughts much appreciated. i like to know why we do things in mechanical repairs not just how we do them. probably a placebo effect - but i think my repairs are better that way.

What oil would you recommend for that type of motor? I have a 2010 lawn tractor and I used 5w30 synthetic and it's burning oil, I was wondering if I should use thicker oil. Thanks.

What is the fuel mixture for this model of blower?

That’s a very scary voice😳 yikes

How rare is this mower with Honda engine. 10:01 6-13-24

Between the air box and carb is a gasket that will prime as long as the primer hole is sealed. It can be leaking or even missing elsewhere but it has to be sealed at the primer orifice for the primer to work. Obviously you don’t want unfiltered air but even if there was unfiltered air it will still run. Take the air box off and it still runs!

Hello, do you have elektrical schematic please?

Thank you!

Great video for a guy like me who loves to cut his grass but has problems with stuff like this I appreciate you really breaking it down and make it easy to understand

nice video please talk louder..no reason to whisper

Thanks from Kelowna ,,,,great close up .. Runs great again

How long does it take to dry??

Greetings, Do you know what size belt was used for this mower deck? Thank you for any input!

This is how to get a wheel off... not a tire.

Anyone now which oil and how much oil I need to put in it?

You solved the mystery to my limited understanding THANK YOU

Hi, do you have the parts number for the 2 springs on the carburetor.

Should of shown the LT 2000 video AS ADVERTISED/CRAFTSMAN NOT MTD

This was a huge help thank you!

👍

If my compression release is not broken, will worn lobes on cam cause me to have to adjust the valves every time before mowing.

Very helpful video! I am about to change both tires tomorrow on the same mower.

Hi , best practice to clean spindle shaft of debris , I find brake cleaner pretty good , and light application of grease to shaft and inside bush , before assembly , a block of wood on face of bearing when refitting will prevent it becoming damaged/ deformed

1:07 how did you do that? There is no gap on mine. Can't figure how to untighten it.

Honda engines are great. Is that 16.5 hp Honda a GXV-530? And does anyone have a part number for an air filter on it? Thank you !

Thanks ,, I was wondering how that spring went. Appreciated.

One thing I learned with bigs in crappin never buy one Even when they're brand new they're junk in a box

My mower runs again after using this video to clean the carburetor. Thanks so much for sharing!

How long is the repair and how much does it cost

1. Not a bearing. It's a bushing. 2. You should always wipe off the grease zirt before greasing. That way, you don't push dirt in and contaminate the grease. Nice video otherwise.

You wouldn't know where I can get replacement tines for that tiller do you

Are you aware of the wind noise?

I lost my manual for my push mower and now I am having a hard time getting na adapter for my mower blade it is a craftsman push mower 6 years old every where I go it’s too small what can I do now

Huh? I can't hear you. =(

Hey, today this video helped me. Thank you 🙏🏻

Dude, stop it with the RTV. Next guy will be looking to choke you out LOL. That crap is such a mess to remove and clean up. Use a simple an cheap paper gasket. This ain't the space program fellas.

Thank you!

I’m about to do this, probably in the morning. It runs on full choke only.

You must not have seen the militaries primitive pete video.

Why are you whispering? Speak up Man !

How much did you quote them?

This is the same exact motor I have in my cub cadet ltx1040. Does this have an oil filter on it?? I've been researching hing for hours and I can't find anything on this motor

What is the part number and where to get it ? Great video, I hope I can find the right part

More of a day of trimming with that piece of junk on a small yard. Not to bad with the chainsaw attachment

let it run for 5 seconds lol those aftermarket chinese carb of craps are junk city!

Does that use compression release like most do nowadays?

Brilliant demo, saved me a lot of bother thanks for sharing this.

voice too quiet, blower too loud